child seat Lexus GX470 2003 How To Use This Manual / LEXUS 2003 GX470 (OM60979U) Owner's Guide

COMFORT ADJUSTMENT
163
(C) Booster seat installation
A booster seat is used in forward−
facing position only.
 Move seat fully back
CAUTION
 A forwardfacing child restraint system should be
allowed to be installed on the front passenger seat
only when it is unavoidable. Always move the seat as
far back as possible, because the force of the
deploying front passenger airbag could cause death
or serious injury to the child.
 Do not allow the child to lean over the front door or
around the front door even if the child is seated in a
child restraint system. It is dangerous if the side
airbag and curtain shield airbag inflate, because the
impact could cause death or serious injury to the
child.

COMFORT ADJUSTMENT
164
 Align both third seatbacks at the same angle
 When installing a child restraint system in the third
center position, align both seatbacks at the same
angle. Otherwise, the child restraint system cannot
be securely restrained and this may cause death or
serious injuries in a collision.
1. Sit the child on a booster seat. Run the lap and shoulder
belt through or around the booster seat and across the child
following the instructions provided by its manufacturer and
insert the tab into the buckle.
Make sure the shoulder belt is correctly across the child’s
shoulder and that the lap belt is positioned as low as possible
on child’s hips. See “Seat belts” on page 123 for details.
CAUTION
 Always make sure the shoulder belt is positioned
across the center of child’ s shoulder. The belt should
be kept away from child’s neck, but not falling off
child’s shoulder. Failure to do so could reduce the
amount of protection in an accident and cause
serious injuries in a collision.

COMFORT ADJUSTMENT
165
Both highpositioned lap belts and loosefitting
belts could cause serious injuries due to sliding
under the lap belt during a collision or other
unintended result. Keep the lap belt positioned as
low on child’s hip as possible.
 For child’s safety, do not place the shoulder belt
under child’s arm.
 After inserting the tab, make sure the tab and buckle
are locked and that the lap and shoulder portions of
the belt are not twisted.
 Do not insert coins, clips, etc. in the buckle as this
may prevent your child from properly latching the tab
and buckle.
 If the seat belt does not function normally,
immediately contact your Lexus dealer. Do not use
the child restraint system until the seat belt is fixed.
It cannot protect your child from injury.
2. To remove the child restraint system, press the
buckle −release button and allow the belt to retract.

COMFORT ADJUSTMENT
166
Using a top strap
Follow the procedure below for a child restraint system
that requires the use of a top strap.
 1 Anchor brackets 2 Symbol mark
Use the anchor brackets on the back of the second seatback
to attach the top strap.
Anchor brackets are installed for each second seating
positions.
This symbol mark indicates the location of user ready anchor
brackets.

COMFORT ADJUSTMENT
167
1. Remove the head restraint.
2. Open the cover of the anchor bracket.
3. Fix the child restraint system with the seat belt.
4. Latch the hook onto the anchor bracket and tighten the
top strap.
For instructions to install the child restraint system, see “Child
restraint system” on page 151.
CAUTION
 Make sure the top strap is securely latched, and
check that the child restraint system is securely by
pushing and pulling it in different directions.
 Follow all the installation instructions provided by its
manufacturer.

COMFORT ADJUSTMENT
168
5. Replace the head restraint.
Be sure to close the cover when the anchor bracket is not in
use.
Installation with child restraint lower
anchorages
The lower anchorages for the child restraint system
interfaced with the FMVSS225 specification are installed
in the second seat.
The anchorages are installed in the seat cushion of the right
side seating position and between the center and left side
seating position.
Child restraint system interfaced with the FMVSS225
specification can be fixed with these anchorages. In this case,
it is not necessary to fix the child restraint system with a seat
belt on the vehicle.

COMFORT ADJUSTMENT
169
CHILD RESTRAINT SYSTEM INSTALLATION
1. Take off the cover on the seat cushion.
2. Widen the slits of the seat cushion a little and confirm
the position of the lower anchorages near the tag on the
seatback.
16PY108

Type A

COMFORT ADJUSTMENT
170
16PY109
 Type B Type A
3. Latch the hooks of lower straps onto the anchorages
and tighten the lower straps.
Type B
3. Latch the buckles onto the anchorages.
If your child restraint system has a top strap, it should be
anchored.
(For the installation of the top strap, see “Using a top
strap” on page 166.)
For the installation details, refer to the instruction manual
equipped with each product.
CAUTION
 When using the lower anchorages for the child
restraint system, be sure that there are no irregular
objects around the anchorages or that the seat belt is
not caught.
 Push and pull the child restraint system in different
directions to be sure it is secure. Follow all the
installation instructions provided by its
manufacturer.
 Do not install a child restraint system on the second
seat if it interferes with the lock mechanism of the
front seats. This can cause death or serious injury to
the child and front passenger in case of sudden
braking or a collision.

COMFORT ADJUSTMENT
171
When using the left side lower anchorages for the
child restraint system, do not sit in the center seat.
The performance of the center seat belt cannot be
brought out sufficiently because the belt may be
highpositioned or the seat belt may be loosefitting,
posing the risk of serious injury in the case of
collision.
DRIVING POSITION MEMORY
SYSTEM
A microcomputer will memorize the position of the driver’s
seat, and the positions of the tilt and telescopic steering, and
outside rear view mirrors. Two dif ferent driving position profiles
can be entered into the computer’s memory.
Recording the driving position in the computer’s memory can
only be done when the ignition key is in the “ON” position and
the selector lever is in the “P” position.
Setting the driving position
1. Adjust the driver’s seat, tilt and telescopic steering and
outside rear view mirrors to the desired position.
2. While pushing the “SET” button, push button “1” or “2”
until the signal beeps.