sensor Lexus GX470 2006 Starting and Driving / LEXUS 2006 GX470 (OM60B99U) Owner's Guide

STARTING AND DRIVING
385
CAUTION
Do not overestimate the antilock brake system:
Although the antilock brake system assists in
providing vehicle control, it is still important to drive
with all due care and maintain a moderate speed and
safe distance from the vehicle in front of you, because
there are limits to the vehicle stability and effectiveness
of steering wheel operation even with the antilock
brake system on.
If tire grip performance exceeds its capability, or if
hydroplaning occurs during high speed driving in the
rain, the antilock brake system does not provide
vehicle control.
Antilock brake system is not designed to shorten the
stopping distance: Always drive at a moderate speed
and maintain a safe distance from the vehicle in front of
you. Compared with vehicles without an antilock
brake system, your vehicle may require a longer
stopping distance in the following cases:
 Driving on rough, gravel or snowcovered roads.
 Driving with tire chains installed.
Driving over the steps such as the joints on the road.
 Driving on roads where the road surface is pitted or
has other differences in surface height.
Install all 4 tires of specified size at appropriate
pressure: The antilock brake system detects vehicle
speeds using the speed sensors for respective wheels’
turning speeds. The use of tires other than specified
may fail to detect the accurate turning speed resulting
in a longer stopping distance.

STARTING AND DRIVING
389
NOTICE
Do not use liquid sealants for a flat tire as air pressure
sensors will be damaged.
 When the tires must be repaired or replaced, have
them repaired or replaced by the nearest Lexus
dealer or authorized tire dealer. The tire pressure
sensors will be affected by the installation or removal
of tires.
 The tire pressure warning system is not to be used as
a substitute for regular inspections. Be sure to check
the air pressure in the tires on a regular basis.
 When the tires must be replaced, replace the
grommets for air pressure sensors as well.
If the warning light blinks:
The tire pressure warning system may be malfunctioning.
Contact your Lexus dealer.
System malfunction
The tire pressure warning system does not function
properly under certain circumstances. In the following
cases, the low tire pressure warning light may not come
on even if the tire inflation pressure is low, or it may come
on when the tire inflation pressure is actually normal.
Electric devices or facilities using similar radio wave
frequencies are nearby.
 A radio set to similar frequencies is in use.
 A lot of snow or ice covers the vehicle, in particular, around
the wheels or wheel housings.
 The tires are not equipped with an air pressure sensor.
 Tire chains are used.
 Non −genuine Lexus wheels are used.
 Although the tires are equipped with air pressure sensors,
the selector switch (see page 393.) is set to other tire setting.

STARTING AND DRIVING
390
CAUTION
The use of nongenuine wheels will cause the air
pressure sensors to transmit the electronic code in
different manner, resulting in the system failure.
 The use of different type of tires with genuine wheels
may also cause the malfunction of the system.
CAUTION
Each tire, including the spare (if provided), should be
checked monthly when cold and inflated to the inflation
pressure recommended by the vehicle manufacturer on
the vehicle placard or tire inflation pressure label (tire
and load information label). (If your vehicle has tires of
a different size than the size indicated on the vehicle
placard or tire inflation pressure label (tire and load
information label), you should determine the proper tire
inflation pressure for those tires.)

STARTING AND DRIVING
392For vehicles sold in Canada
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this de-
vice must accept any interference, including interference
that may cause undesired operation of the device.
Replacing tires and wheels
When replacing the wheels, be sure to install air pressure
sensors on the wheels.
There are 3 ways to set up the air pressure sensors:
(a) Remove the sensor
from the old wheel and install it to the
new wheel.
(b) Keep the same wheel with air pressure sensor and replace
only the tire.
(c) Use a new wheel and sensor.
You have to register an ID code for a new sensor. Up to 2 sets
of codes can be registered. As one ID for the originally installed
sensor is registered at “MAIN” of the selector switch, use the
“2nd” position to register an ID for the new sensor.
You do not need to re −register the ID code for any other
replacements. For the use of the originally installed tires, put
the selector switch at “MAIN” and for the use of tires set
purchased later, put the switch at “2nd”. For the sensor
selector switch, see page 393.

STARTING AND DRIVING
393
CAUTION
Have the tires, wheels or sensors replaced and ID
codes registered by a Lexus dealer. If you need
sensors, purchase from a Lexus dealer.
 The use of nongenuine wheels will cause the air
pressure sensors to transmit the electronic code in
different manner, resulting in the failure of the
system.
Selector switch
1Main position22nd position
The selector switch is located in the lower part of the
driver’s side instrument panel.
The ID code is given in the sensor. To activate the air
pressure wa rning system, it is necessary to register the ID
code of the sensor on the selector switch in the vehicle.

STARTING AND DRIVING
3942 sets of ID codes can be registered. The code of the tires
originally
installed on the vehicle is registered on the switch at
“MAIN”. Have a new tires set with new air pressure sensors
registered at “2nd” by Lexus dealer.
ID codes should be registered by Lexus dealer. Once
registered, change the setting position each time you purchase
tires and wheels. Re −registration is not required.
When purchasing new tires, consult your Lexus dealer.
CAUTION
When the tires whose ID code is registered at “MAIN”
are used, the system does not work properly with the
selector switch set at “2nd”. If the tires whose ID code
is registered at “2nd” are stored nearby, the system will
detect their tire pressure (and vice versa).
BRAKE PAD WEAR LIMIT INDICATORS
The brake pad wear limit indicators on your disc brakes
give a warning noise when the brake pads are worn to the
extent that replacement is required.
If you hear a squealing or scraping noise while driving, have the
brake pads checked and replaced by your Lexus dealer as
soon as possible. Expensive rotor damage can result if the
pads are not replaced when needed.

ELECTRICAL COMPONENTS
549
No.FUSEAMPERECIRCUIT
29ECUB10
Multiplex communication
system, vehicle stability control
system, wireless remote
control system, inside rear
view mirror, air conditioning
system, electronic modulated
suspension, driving position
memory system, power
windows, moon roof, rear view
monitor system
30ECUBNO.210Theft deterrent system
31ABS
MTR40
Anti −lock brake system,
vehicle stability control system,
active traction control system,
brake assist system
32AM230Starting system, all components
in “IGN”, “SRS”, “GAUGE” and
“ST2” fuses
33ABS
SOL30
Anti −lock brake system,
vehicle stability control system,
active traction control system,
brake assist system
No.FUSEAMPERECIRCUIT
34ALTS7.5Charging system
35MAYDAY7.5Lexus Link System
36HORN10Horns
37A/F
HEATER15A/F sensor
38TRNHAZ15Turn signal lights
39ETCS10Electronic throttle control system
40EFI20Multiport fuel injection
system/sequential multiport fuel
injection system
41D FR P/W20Power window
42DR/LCK25Power door lock
43TOWING30Towing converter
44RADIO NO.230Audio system, navigation
system
45A/PUMP50Multiport fuel injection
system/sequential multiport fuel
injection system
46IGN10
Multiport fuel injection
system/sequential multiport fuel
injection system, vehicle
stability control system

BODY
571
Carpets, Windows and Seat Belts
Begin by vacuuming thoroughly to remove as much dirt as
possible. Several types of foam cleaners are available; some
are in aerosol cans and others are powders or liquids which
you mix with water to produce a foam. To shampoo the
carpets, use a sponge or brush to apply the foam. Rub in
overlapping circles. Do not apply water — the best results are
obtained by keeping the carpet as dry as possible. Read the
shampoo instructions and follow them closely.
The seat belts may be cleaned with mild soap and water or
with lukewarm water.
Use a cloth or sponge. As you are cleaning, check the belts for
excessive wear, fraying or cuts.NOTICE
 Use a good foamtype shampoo to clean the carpets.
 Do not use dye or bleach on the belts — it may
weaken them.
 Do not use the belts until they become dry.
 The windows may be cleaned with any household
window cleaner.
 Do not apply detergent to or wet the automatic wiper
control sensor when cleaning the inside of the
windshield.
 When cleaning the inside of the quarter and rear
windows, be careful not to scratch or damage the
wire antennas, heater wires or connectors.