display LEXUS IS250 2016 User Guide

134
2-1. Driving procedures
Changing shift ranges in S mode
To enter S mode, shift the shift lever to the S position. The shift range can
then be selected by operating the “-” and “+” shift paddle switches or the
shift lever. Changing the shift range allows restriction of the upper limit of
the gears to be used, preventing unnecessary upshifting and enabling the
level of engine braking force to be selected.
Higher shift range
Lower shift range
The selected shift range, from 1 to
6, will be displayed in the meter
cluster.
The initial shift range in S mode is automatically set to 5 or 4 according to
vehicle speed. However, the initial shift range may be set to 3 or 2 if the
AI-SHIFT has operated while the shift lever was in the D position.
(→P. 1 3 6 )
nShift ranges and their functions
→P. 13 3

135
2-1. Driving procedures
2

When driving
nWhen the “-” shift paddle switch is operated in the D position
When the “-” shift paddle switch is operated in the D position, a shift range will be
automatically selected. The highest gear of the first shift range will be one gear
lower than the gear in use during normal D position driving.
nAutomatic deactivated of shift range selection in the D position
Shift range selection in the D position will be deactivated in the following situations:
lWhen the vehicle comes to a stop
lWhen range 6 is selected and the accelerator pedal is depressed
lIf the accelerator pedal is depressed for more than a certain period of time
nGear position display when driving
The current gear is displayed on the multi-information display. (→P. 1 5 4 )
nDownshifting restrictions warning buzzer
To help ensure safety and driving performance, downshifting operation may some-
times be restricted. In some circumstances, downshifting may not be possible even
when the shift lever or shift paddle switch is operated. (The warning buzzer will
sound twice.)
nWhen driving with the cruise control system or dynamic radar cruise control sys-
tem
Engine braking will not occur during shift range selection in the D position or S
mode, even when downshifting to range 5 or 4. (→P. 166, 170)
nSnow mode automatic deactivation
Snow mode is automatically deactivated if the “ENGINE START STOP” switch is
turned off after driving in snow mode.
nIf the shift lever cannot be shifted from P
→P. 41 5

142
2-2. Instrument cluster
Gauges and meters
The units used on the speedometer and the tachometer gauge display may
differ depending on the model/type.
The following gauges, meters and display illuminate when the
“ENGINE START STOP” switch is in IGNITION ON mode.
Speedometer
Displays the vehicle speed.
Multi-information display
→P. 1 5 1
Tachometer
Displays the engine speed in revolutions per minute.
Tacho indicator
When the set engine speed is reached, this ring-shaped indicators comes
on in yellow. The indicator comes on in red when the engine speed
reaches a dangerous range.
Engine coolant temperature gauge
Displays the engine coolant temperature.

143
2-2. Instrument cluster
2

When driving
Instrument panel light control
The brightness of the instrument panel lights can be adjusted.
Darker
Brighter
Odometer and trip meter
Odometer:Displays the total distance the vehicle has been driven.
Trip meter: Displays the distance the vehicle has been driven since
the meter was last reset. Trip meters “A” and “B” can be
used to record and display different distances indepen-
dently.
Speed indicator
When the set speed is reached while driving, this ring-shaped indicator
comes on in yellow. The indicator comes on in red when the vehicle speed
reaches the dangerous range.
Fuel gauge
Displays the quantity of fuel remaining in the tank.
Odometer/trip meter and trip meter reset button
Switches between odometer and trip meter displays. Pushing and holding
the button will reset the trip meter when the trip meter is being displayed.

144
2-2. Instrument cluster
Speed and tacho indicators
nTurning the indicator on/off
Bring up the satellite switch mode
on the multi-information display.
Press <, > or the “ON/OFF” but-
ton.
Select the item whose setting is to
be changed.
Press < or > to display the item
whose setting is to be changed.
Change the settings.
Press “ON/OFF” button to change
the settings.
STEP1
STEP2
STEP3

146
2-2. Instrument cluster
Push < or > within 6 seconds of the speedometer or tachometer needle
moving to change the setting of the desired speed, then turn the indicator
mode to “ON” by pushing the “ON/OFF” button.
Pushing and holding the button changes values at a faster rate.
If the satellite switch is not operated for some time, the multi-information dis-
play returns to its previously displayed content.
The yellow indicator is displayed to indicate that the desired speed has
been set.
STEP2
nSpeed indicator display conditions and vehicle speed setting range
Vehicle speed setting range: Approximately 30 to 100 mph
(approximately 50 to 160 km/h)
When the maximum speed is selected, the speed indicator comes on only in red.
nTacho indicator display conditions and engine speed setting range
Engine rpm setting range: Approximately 2000 to 6500 rpm (r/min)
When the maximum rpm is selected, the tacho indicator comes on only in red.

148
2-2. Instrument cluster
Indicators and warning lights
The indicator and warning lights on the instrument cluster and center
panel inform the driver of the status of the vehicle’s various systems.
Instrument cluster
The units used on the speedometer and the tachometer gauge display may
differ depending on the model/type.
Center panel

151
2-2. Instrument cluster
2

When driving
Multi-information display
The multi-information display presents the driver with a variety of driving-
related data, including the current outside air temperature.
lTrip information (→P. 152)
Displays driving range, fuel con-
sumption and other cruising
related information.
lSatellite switch mode display
(→P. 260)
This switch is used to configure
various function settings.
lIntuitive parking assist dis-
play (if equipped) (→P. 180)
Automatically displayed when
using intuitive parking assist.
lDynamic radar cruise con-
trol display (if equipped)
(→P. 170)
Automatically displayed when
using dynamic radar cruise con-
trol.
lWarning messages
(→P. 392)
Automatically displayed when a
malfunction occurs in one of the
vehicle’s systems.

152
2-2. Instrument cluster
Trip information
Without navigation system
Display items can be switched by
pushing the “DISP” switch.
With navigation system
nOutside temperature
Displays the outside air temperature.
The temperature range that can be displayed is from
-40°F (40°C) to 122°F (50°C).
When the temperature drops to 37°F (3°C), the dig-
its of the display will flash for 10 seconds.

153
2-2. Instrument cluster
2

When driving
nDriving range
nAverage fuel consumption
nAverage fuel consumption after refueling
nCurrent fuel consumption
nAverage vehicle speed
Displays the estimated maximum distance that can
be driven with the quantity of fuel remaining.