display lexus LC500 2018 Owners Manual

233
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
Example of acceleration
When there are no longer any preceding vehicles driving slower than the set
speed
The system accelerates until the set speed is reached. The system then returns to constant
speed cruising.
1 Press the cruise control main switch
to activate the cruise control.
Radar cruise control indicator will come on and a message will be displayed on the multi-information display.
Press the switch again to deactivate the cruise control.
If the cruise control main switch is pressed and held for 1.5 seconds or more, the sys-
tem turns on in constant speed control mode. ( P.236)
2Accelerate or decelerate, with
accelerator pedal operation, to the
desired vehicle speed (at or above
approximately 50 km/h [30 mph])
and press the -/SET switch to set
the speed.
Cruise control “SET” indicator will come
on.
The vehicle speed at the moment the
switch is released becomes the set speed.
If the switch is operated while the vehicle
speed is below approximately 50 km/h (30 mph) and a preceding vehicle is pres-ent, the set speed will be adjusted to
approximately 50 km/h (30 mph).
To change the set speed, press the
+/RES or -/SET switch until the
desired set speed is displayed.
1 Increases the speed
(Except when the vehicle has been
stopped by system control in vehi-
cle-to-vehicle distance control
mode)
2 Decreases the speed
Fine adjustment: Press the switch.
C
Setting the vehicle speed (vehi-
cle-to-vehicle distance control
mode)
Adjusting the set speed

235
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
DrivingAfter the vehicle ahead of you starts
off, press the +/RES switch.
Your vehicle will also resume follow-up
cruising if the accelerator pedal is
depressed after the vehicle ahead of
you starts off.
1 Pressing the cancel switch cancels
the speed control.
The speed control is also canceled when
the brake pedal is depressed.
(When the vehicle has been stopped by
system control, depressing the brake pedal
does not cancel the setting.)
2 Pressing the +/RES switch resumes
the cruise control and returns vehi-
cle speed to the set speed.
However, when a vehicle ahead is not
detected, cruise control does not resume
when the vehicle speed is approximately
40 km/h (25 mph) or less.
When your vehicle is too close to a
vehicle ahead, and sufficient automatic
deceleration via the cruise control is
not possible, the display will flash and
the buzzer will sound to alert the driver.
An example of this would be if another
driver cuts in front of you while you are
following a vehicle. Depress the brake
pedal to ensure an appropriate vehi-
cle-to-vehicle distance.
Distance optionsVehicle-to-vehicle
distance
LongApproximately 50
m (160 ft.)
MediumApproximately 40
m (130 ft.)
ShortApproximately 30
m (100 ft.)
Resuming follow-up cruising
when the vehicle has been
stopped by system control (vehi-
cle-to-vehicle distance control
mode)
Canceling and resuming the
speed control
Approach warning (vehicle-to-
vehicle distance control mode)

237
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
selected by using the paddle shift switch.
●Vehicle speed is at or above approxi-
mately 50 km/h (30 mph). However, when a preceding vehicle is detected, the dynamic radar cruise con-
trol with full-speed range can be set even if the vehicle speed is below approxi-mately 50 km/h (30 mph).
■Accelerating after setting the vehicle
speed
The vehicle can accelerate by operating the
accelerator pedal. After accelerating, the set speed resumes. Ho wever, during vehi- cle-to-vehicle distance control mode, the
vehicle speed may decrease below the set speed in order to maintain the distance to the preceding vehicle.
■When the vehicle stops while follow-up
cruising
●Pressing the +/RES switch while the vehi-
cle ahead stops will resume follow-up cruising if the vehicle ahead starts off within approximately 3 seconds after the
switch is pressed.
●If the vehicle ahead starts off within 3 sec-
onds after your vehicle stops, follow-up cruising will be resumed.
■Automatic cancelation of vehicle-to-
vehicle distance control mode
Vehicle-to-vehicle distance control mode is
automatically canceled in the following situ- ations.
●Actual vehicle speed falls below approxi-mately 40 km/h (25 mph) when there are no vehicles ahead.
●The preceding vehicle leaves the lane when your vehicle is following at a vehicle
speed below approximately 40 km/h (25 mph). Otherwise, the sensor can not properly detect the vehicle. (“CRUISE
NOT AVAILABLE No Preceding Vehi- cles” is displayed on the multi-information display.)
●VSC is activated.
●TRC is activated for a period of time.
●When the VSC or TRC system is turned
off.
●When snow mode is set.
●The sensor cannot detect correctly
because it is covered in some way.
●Pre-collision brakin g is activated.
●The parking brake is operated.
●The vehicle is stopped by system control on a steep incline.
●The following are detected when the vehicle has been stopped by system con-trol:
• The driver is not wearing a seat belt. • The driver’s door is opened.• The vehicle has been stopped for about 3
minutes
If vehicle-to-vehicle distance control mode
is automatically canceled for any other rea-
son, there may be a malfunction in the sys-
tem. Contact any authorized Lexus retailer
or Lexus authorized repairer, or any reliable
repairer.
■Automatic cancelation of constant speed control mode
Constant speed control mode is automati- cally canceled in the following situations:
●Actual vehicle speed is more than
approximately 16 km/h (10 mph) below the set vehicle speed.
●Actual vehicle speed falls below approxi-mately 40 km/h (25 mph).
●VSC is activated.
●TRC is activated for a period of time.
●When the VSC or TRC system is turned off.
●Pre-collision brakin g is activated.
If constant speed control mode is automati-
cally canceled for any other reason, there
may be a malfunction in the system. Con-
tact any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer.
■If “Radar Cruise Control Unavailable” is
shown on the multi-information display
The radar cruise control system cannot be
used temporarily. Use the system when it

238
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
becomes available again.
■Warning messages and buzzers for dynamic radar cruise control with full-speed range
Warning messages and buzzers are used to indicate a system malfun ction or to inform
the driver of the need for caution while driv- ing. If a warning mess age is shown on the multi-information display, read the message
and follow the instructions.
■When the sensor may not be correctly detecting the vehicle ahead
In the case of the following and depending on the conditions, operate the brake pedal when deceleration of the system is insuffi-
cient or operate the accelerator pedal when acceleration is required.
As the sensor may not be able to correctly detect these types of vehicles, the approach warning ( P.235) may not be activated.
●Vehicles that cut in suddenly
●Vehicles traveling at low speeds
●Vehicles that are not moving in the same
lane
●Vehicles with small rear ends (trailers with no load on board, etc.)
●Motorcycles traveling in the same lane
●When water or snow thrown up by the
surrounding vehicles hinders the detect- ing of the sensor
●When your vehicle is pointing upwards (caused by a heavy load in the luggage compartment, etc.)
●Preceding vehicle has an extremely high ground clearance
■Conditions under which the vehicle-to-vehicle distance control mode may not function correctly
In the case of the following conditions, operate the brake pedal (or accelerator
pedal, depending on the situation) as nec- essary.
As the sensor may not be able to correctly detect vehicles ahead, the system may not operate properly.
●When the road curves or when the lanes
are narrow
●When steering wheel operation or your
position in the lane is unstable

239
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
●When the vehicle ahead of you deceler- ates suddenly
*:If equipped
■Meter display
Set speed
Indicators
■Operation switches
+/RES switch
Cruise control main switch
-/SET switch
Cancel switch
Cruise control*
Use the cruise control to maintain a
set speed without depressing the
accelerator pedal.
System components
A
B
A
B
C
D

241
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
Resuming is available when the vehicle
speed is more than approximately 40
km/h (25 mph).
■Cruise control can be set when
●The shift position is in D.
●LC500: Range 4 or higher of D has been selected by using the paddle shift.
●Vehicle speed is above approximately 40 km/h (25 mph).
■Accelerating after setting the vehicle speed
●The vehicle can be accelerated normally. After acceleration, the set speed
resumes.
●Even without canceling the cruise con-
trol, the set speed can be increased by first accelerating the vehicle to the desired speed and then pressing the -
/SET switch to set the new speed.
■Automatic cruise control cancelation
Cruise control will stop maintaining the
vehicle speed in any of the following situa- tions.
●Actual vehicle speed falls more than approximately 16 km/h (10 mph) below the preset vehicle speed.
●Actual vehicle speed is below approxi-mately 40 km/h (25 mph).
●VSC is activated.
●TRC is activated for a period of time.
●When the VSC or TRC system is turned
off.
■If the warning message for the cruise control is shown on the multi-informa-tion display
Press the cruise control main switch once to deactivate the system, and then press the
switch again to reactivate the system. If the cruise control speed cannot be set or if the cruise control cancels immediately
after being activated, there may be a mal- function in the cruise control system. Have the vehicle inspected by authorized Lexus
retailer or Lexus authorized repairer, or any
reliable repairer.
WARNING
■To avoid operating the cruise control
by mistake
Switch the cruise control off using the
cruise control main switch when not in use.
■Situations unsuitable for cruise con-trol
Do not use cruise control in any of the following situations.
Doing so may result in loss of control and could cause an accident resulting in death or serious injury.
●In heavy traffic
●On roads with sharp bends
●On winding roads
●On slippery roads, such as those cov-
ered with rain, ice or snow
●On steep downhills Vehicle speed may exceed the set speed when driving down a steep hill.
●During emergency towing

242
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
1Normal mode/Custom mode
Normal mode and custom mode are
selected by pressing the driving mode
select switch. Each time the switch is
pressed, the driving mode changes
between normal mode and custom mode.
When custom mode is selected, the “Cus-
tom” indicator comes on.
Press the switch to change the driving
mode to normal mode when not in normal
mode.
• Normal mode
Provides an optimal balance of fuel econ-
omy, quietness, and dynamic performance.
Suitable for city driving.
When the shift position is in D, an appropri-
ate gear for sporty driving may automati-
cally be selected according to driver
performance and driving conditions.
• Custom mode
Allows you to drive with the power train,
chassis and air conditioning system func-
tions set to your preferred settings.
Custom mode settings can only be
changed on the drive mode customization
display of Center Display. ( P.275)
2Comfort mode
By controlling the suspension, riding com-
fort is further enhanced. Suitable for city
driving.
When not in comfort mode and the driving
mode select switch is turned forward, the
“Comfort” indicator comes on.
3 Eco drive mode
Helps the driver accelerate in an eco-
friendly manner and improve fuel economy
through moderate throttle characteristics
and by controlling the operation of the air
conditioning system (heating/cooling).
When in comfort mode, if the driving mode
select switch is turned forward, the “Eco”
indicator comes on.
4 Sport mode
•SPORT S mode
Controls the transmission and engine to
provide quick, powerful acceleration. This
mode is suitable for when agile driving
response is desired, such as when driving
on roads with many curves.
When not in SPORT S mode, if the driving
mode select switch is turned backward, the
“Sport S” indicator comes on.
•SPORT S+ mode
Provides earlier downshift timing than
SPORT S mode in order to maintain a high
engine speed and provides faster gear
changes. This mode also changes the
Driving mode select switch
The driving modes can be selected
to suit driving condition.
Selecting the driving mode

243
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
steering feel, suspension control and
VDIM control, making it suitable for pow-
erful sporty driving.
When in SPORT S mode, if the driving
mode select switch is turned backward, the
“Sport S+” indicator comes on.
■Operation of the air conditioning sys- tem in Eco drive mode
Eco drive mode controls the heating/cool- ing operations and fan speed of the air con-ditioning system to enhance fuel efficiency.
To improve air conditioning performance, perform the following operations:
●Adjust the fan speed ( P.281, 283)
●Turn off Eco drive mode
■Automatic deactivation of sport mode
and custom mode
If the engine switch <power switch> is
turned off after driving in sport mode or custom mode, the drive mode will be changed to normal mode.
■Driving mode pop-up display
When the driving mode is changed, the selected driving mode will be temporarily
displayed on the side display. ( P.277)
For custom mode, select “Setting” on the
display to customize the driving mode.
■Types of sensors
Front corner sensors
Front center sensors
Rear corner sensors
Rear center sensors
■Display
When the sensors detect an obstacle, a
graphic is shown on the multi-informa-
tion display, head-up display and Cen-
ter Display depending on the position
and distance to the obstacle.
 Multi-information display and head-
Lexus parking assist-sensor
The distance from your vehicle to
nearby obstacles when parallel
parking or maneuvering into a
garage is measured by the sensors
and communicated via the multi-
information display, head-up dis-
play (if equipped), Center Display
and a buzzer. Always check the sur-
rounding area when using this sys-
tem.
System components
A
B
C
D

244
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
up display
Front corner sensor detection
Front center sensor detection
Rear corner sensor detection
Rear center sensor detection
 Center Display
A graphic is shown when the Lexus park-
ing assist monitor is displayed (insert dis-
play)
A simplified image is displayed on the
upper right corner of Center Display when
an obstacle is detected.
1 Press or of the meter con-
trol switches, and select .
2 Press or of the meter con-
trol switches, and select “Parking
Assist”, and press “OK”.
When the Lexus parking assist-sensor
is turned on, the Lexus parking assist-
sensor indicator comes on to inform
the driver that the system is opera-
tional.
■The Lexus parking assist-sensor can be
operated when
●Front center sensors:
• The engine switch <power switch> is in IGNITION ON mode <ON mode>.
• The shift position is in a position other than P or R.• The vehicle speed is less than about 10
km/h (6 mph).
●Front corner sensors:
• The engine switch <power switch> is in IGNITION ON mode <ON mode>.• The shift position is in a position other
than P. • The vehicle speed is less than about 10 km/h (6 mph).
(At any speed when the shift position is in R)
●Rear corner and rear center sensors:• The engine switch <power switch> is in IGNITION ON mode <ON mode>.
• The shift position is in R.
■Muting the buzzer sound
●To mute the buzzer sound:
The buzzer can be temporarily muted by pressing “OK” of the meter control switches
while an obstacle detection display is shown on the multi-information display.
●To cancel the mute:
Mute will be automatically canceled in the
following situations. • When the shift position is changed (except shifting from D to N, or N to D)
• When the vehicle speed has reached or exceeded 10 km/h (6 mph) with the shift position in D
Turning Lexus parking assist-sen-
sor on/off
A
B
C
D

245
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
• When the Lexus parking assist-sensor is turned off once and turned on again• When the engine switch <power switch>
is turned off once and turned to IGNI- TION ON mode <ON mode> again
■If “Clean Parking Assist Sensor” is dis-played on the multi-information display
A sensor may be dirty or covered with snow or ice. In such cases, if it is removed from
the sensor, the system should return to nor- mal.
Also, due to the sensor being frozen at low temperatures, a malfunction display may appear or an obstacle may not be detected.
If the sensor thaws out, the system should return to normal.
■If “Parking Assist Malfunction” or “Park-ing Assist Malfunction Visit Your
Dealer” is displayed on the multi-infor- mation display
There is a malfunction and the device may not be working properly.
Have the vehicle inspected by any autho- rized Lexus retailer or Lexus authorized repairer, or any reliable repairer.
■Sensor detection information
●The sensor’s detection areas are limited
to the areas around the vehicle’s front and rear bumpers.
●Certain vehicle conditions and the sur-rounding environment may affect the ability of the sensor to correctly detect
obstacles. Particular instances where this may occur are listed below.• There is dirt, snow or ice on the sensor.
(Wiping the sensors will resolve this problem.)• The sensor is frozen. (Thawing the area
will resolve this problem.)
In especially cold weather, if a sensor is fro-
zen the screen may show an abnormal dis-
play, or obstacles may not be detected.
• The sensor is covered in any way.
• The vehicle is leaning considerably to one side.• On an extremely bumpy road, on an
incline, on grav el, or on grass. • The vicinity of the vehicle is noisy due to
vehicle horns, motorcycle engines, air brakes of large vehicles, or other loud noises producing ultrasonic waves.
• There is another vehicle equipped with parking assist sensor in the vicinity.• The sensor is splashed with water or
heavy rain. • The vehicle is equipped with a fender pole or wireless antenna.
• Towing eyelets are installed. • The bumper or sensor receives a strong impact.
• The vehicle is approaching a tall or curved curb.• In harsh sunlight or intense cold weather.
• The area directly under the bumpers is not detected.• If obstacles draw too close to the sensor.
• A non-genuine Lexus suspension (low- ered suspension etc.) is installed.• People may not be detected if they are
wearing certain types of clothing.
In addition to the examples above, there are
instances in which, because of their shape,
signs and other objects may be judged by
the sensor to be closer than they are.
●The shape of the obstacle may prevent the sensor from detecting it. Pay particu-
lar attention to the following obstacles: • Wires, fences, ropes, etc.• Cotton, snow and other materials that
absorb sound waves • Sharply-angled objects•Low obstacles
• Tall obstacles with upper sections pro- jecting outwards in the direction of your vehicle
●The following situations may occur during use.
• Depending on the shape of the obstacle and other factors, the detection distance may shorten, or detection may be impos-
sible. • Obstacles may not be detected if they are too close to the sensor.
• There will be a short delay between obstacle detection and display. Even at slow speeds, there is a possibility that the
obstacle will come within the sensor’s detection areas before the display is shown and the warning beep sounds.