display lexus LC500 2018 Owner's Manual

265
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
■EPS, VGRS and DRS operation sound
When the steering wheel is operated, a
motor sound (whirring sound) may be heard. This does not indicate a malfunction.
■Automatic reactivation of TRC and VSC systems
After turning the TRC and VSC systems off, the systems will be automatically re-
enabled in the following situations:
●When the engine switch <power switch>
is turned off
●If only the TRC system is turned off, the
TRC will turn on when vehicle speed increases
If both the TRC and VSC systems are turned off, automatic re-enabling will not occur when vehicle speed increases.
■Secondary Collision Brake operating
conditions
The vehicle speed is approximately 10 km/h
(6 mph) or more and the airbag sensor detects a collision. (The Secondary Colli-sion Brake will not operate when the vehicle
speed is below approximately 10 km/h [6 mph].)
■Secondary Collision Brake automatic
cancellation
The Secondary Collision Brake is automati-
cally canceled in the following situations:
●The vehicle speed drops below approxi-
mately 10 km/h (6 mph)
●A certain amount of time elapses during
operation
●The accelerator pedal is depressed a
large amount
■If “Check Secondary Collision Brake system” is displayed on the multi-infor-mation display
The system may be malfunctioning. Have the vehicle inspected at any authorized
Lexus retailer or Lexus authorized repairer, or any reliable repairer.
■Reduced effectiveness of the EPS sys-tem
The effectiveness of the EPS system is
reduced to prevent the system from over- heating when there is frequent steering input over an extended period of time. The
steering wheel may feel heavy as a result. Should this occur, refrain from excessive steering input or stop the vehicle and turn
the engine <hybrid system> off. The EPS sys- tem should return to normal within 10 min-utes.
■Operating conditions of emergency
brake signal
When the following three conditions are
met, the emergency brake signal will oper- ate:
●The emergency flashers are off.
●Actual vehicle speed is over 55 km/h
(35 mph).
●The brake pedal is depressed in a manner
that cause the system to judge from the vehicle deceleration that this is a sudden braking operation.
■Automatic system cancelation of emer-
gency brake signal
The emergency brake sign al will turn off in
any of the following situations:
●The emergency flashers are turned on.
●The brake pedal is released.
●The system judges from the vehicle deceleration that is not a sudden braking
operation.
WARNING
■The ABS does not operate effectively when
●The limits of tire gripping performance have been exceeded (such as exces-
sively worn tires on a snow covered road).
●The vehicle hydroplanes while driving at high speed on wet or slick roads.

274
-$@-$I@0.@0.&@ &&

5-1. Remote Touch
5-1.Remote Touch
■Switches
“MAP” button (vehicles with navi-
gation system)/ “HOME” button
(vehicles without navigation sys-
tem)
“MAP” button: Press to display the current
location.
“HOME” button: Press to display the home
screen.
“MENU” button
Press to display the menu screen.
Back button
Press to display the previous screen.
Touchpad
Slide your finger on the touchpad and
move the pointer to select a function, letter
and screen button.
Press the touchpad to enter the selected
function, letter or screen button. Certain
finger movements on the touchpad can
perform functions, such as changing map
scalings and scrolling list screens.
Sub function button
When is displayed on the screen, a
function screen assigned to the screen can
be displayed.
■Using the touchpad
1 Select: Touch the touchpad to
select the desired button on the
screen.
2 Enter: The buttons on the screen
can be selected by either depress-
ing or double tapping on the
touchpad. Once a button has been
selected, the screen will change.
■Touch operation
Operations are performed by touching
the touchpad with your finger.
 Trace
Trace the pad surface while maintaining
contact with the touchpad. Moving the
cursor and the pointer.
Remote Touch
The Remote Touch can be used to
operate Center Display.
For details on the Remote Touch,
refer to the “NAVIGATION SYS-
TEM OWNER’S MANUAL”.
Remote Touch operation
A
B
C
D
E

275
5
-$@-$I@0.@0.&@ &&

5-1. Remote Touch
Interior features
Double tap
Tap the touchpad twice, quickly. Select the
button on the screen.
 Flick
Quick and long movement along the
touchpad with you finger. Move the list
screen.
 Pinch in/Pinch out
Slide fingers toward each other or apart on
the touchpad. Change the scale of the
map.
■Menu screen
Press the “MENU” button on the
Remote Touch to display the menu
screen.
The display may differ depending on
the type of the system.
NOTICE
■To prevent damage to the Remote Touch
Observe the following precautions. Fail- ure to do so may cause damage to the Remote Touch.
●Do not allow the Remote Touch to
come into contact with food, liquid, stickers or lit cigarettes.
●Do not subject the Remote Touch to excessive pressure or strong impact.
●Do not push the touchpad with a
strong force or use a sharp pointed object to operate the pad.
Center Display overview

276
-$@-$I@0.@0.&@ &&

5-1. Remote Touch
*1: Refer to the “NAVIGATION SYSTEM
OWNER’S MANUAL”.
*2: If equipped
■Split-screen display
Different information can be displayed on the left and right of the screen. For
example, air conditioning system screen can be displayed and operated while the
fuel consumption information screen is be ing displayed. The large screen on the
left of the display is called the main display, and the small screen to the right is
called the side display.
SwitchFunction
Select to display the “Destina-
tion” screen.*1, 2
Select to display the radio con-
trol screen.*1
Select to operate the media
control screen.*1
Select to display the hands-free
control screen.*1
Select to display “Apps”
screen.*1, 2
Select to display the information
screen.*1 ( P.104, 107)
Select to display the “Setup”
screen.*1
Select to display the air condi-
tioning control screen.
( P.283)
SwitchFunction

277
5
-$@-$I@0.@0.&@ &&

5-1. Remote Touch
Interior features
■Main display
For details about the functions and
operation of the main display, refer to
the respective section and “NAVIGA-
TION SYSTEM OWNER’S MAN-
UAL”.
■Side display
The following functions can be dis-
played and operated on the side dis-
play.
Select or to display the desired
screen.
Navigation system*
Audio*
Vehicle information ( P.108)
Air conditioning system ( P.284)
Show/hide the side display
*: Refer to the “NAVIGATION SYSTEM
OWNER’S MANUAL”.
■Screen display during low temperatures
When the ambient temperature is
extremely low, screen response may be delayed even if the Remote Touch is oper-ated.
A
B
C
D
E

278
-$@-$I@0.@0.&@ &&

5-2. Lexus Climate Concierge
5-2.Lexus Climate Concierge
Select
The indicator on the Lexus Climate Con-
cierge control screen illuminates, and the
automatic air conditioning system, seat
heaters and ventilators, and heated steer-
ing wheel operate in automatic mode.
If any of the system is operated manually,
the indicator turns off. However, all other
functions continue to operate in automatic
mode.
■When using the Lexus Climate Con- cierge
Lexus Climate Concierge can be operated on the sub function menu or option control screen. ( P.283)
■Automatic air conditioning system
( P.280)
The temperature can be adjusted indi-
vidually for the driver seat and passen-
ger seat.
■Seat heaters and ventilators
( P.288)
Heating or ventilation is automatically
selected according to the set tempera-
ture of the air conditioning system, the
outside temperature, etc.
The seat heater and ventilator of the
front passenger seat operate in auto-
matic mode if a passenger is detected.
■Heated steering wheel (if
equipped) ( P.288)
Heated steering wheel operates auto-
matically according to the set tempera-
ture of the air conditioning system, the
outside temperature, etc.
Lexus Climate Concierge
The seat heaters, seat ventilators
and heated steering wheel (if
equipped) are each automatically
controlled according to the set
temperature of the air conditioning
system, the outside and cabin tem-
perature, etc. Lexus Climate Con-
cierge allows a comfortable
condition to be maintained without
adjusting each system.
Press the “MENU” button on the
Remote Touch and select “Climate”
to display the air conditioning con-
trol screen. Then, select on the
sub menu ( P.283) to display the
Lexus Climate Concierge control
screen.
Turning on Lexus Climate Con-
cierge
Operation of each system

280
-$@-$I@0.@0.&@ &&

5-3. Using the air conditioning system
5-3.Using the air conditioning system
Automatic mode switch
Off switch
Left-hand side temperature control switch
Fan speed control switch
Outside/recirculated air mode switch
Right-hand side temperature control switch
Windshield defogger switch
Rear window and outside rear view mirror defoggers switch
Automatic air conditioning system
Air outlets and fan speed are automatically adjusted according to the tem-
perature setting.
Press the “MENU” button on the Remote Touch, then select “Climate” to dis-
play the air conditioning control screen. ( P.275)
The air conditioning system can be disp layed and operated on the side display.
The illustrations below are for left-hand drive vehicles.
The button positions and shapes will di ffer for right-hand drive vehicles.
Air conditioning controls
A
B
C
D
E
F
G
H

283
5
-$@-$I@0.@0.&@ &&

5-3. Using the air conditioning system
Interior features
■Main control screen
Using the touchpad of the Remote
Touch, select the button on the screen.
to can be adjusted by perform-
ing the following operations.
Flick operation: Move the pointer to
the desired item and flick the touchpad
up or down.
The item can be adjusted by one level.
Trace operation: After selecting the
desired item, trace the pad surface.
The item can be adjusted by the amount
that you trace.
Trace operation cannot be used while driv-
ing.
Sub menu
Selecting the sub menu item to switch the
main screen.
: Display the air conditioning control
screen
: Display the heated steering
wheel/seat heater/seat ventilator control
screen (if equipped)
: Display the Lexus Climate Con-
cierge control screen
: Display the option control screen
Adjust the left-hand side tempera-
ture setting
Adjust the fan speed setting
Select the air flow mode
: Air flows to the upper body
: Air flows to the upper body and
feet
: Air flows to the feet
: Air flows to the feet and the wind-
shield defogger operates
Adjust the right-hand side tem-
perature setting
Function on/off indicators
When the function is on, the indicator illu-
minates on the control screen.
Sub function menu
When the sub function button on the
Remote Touch is pressed, the following
functions can be switched on and off.
: Set Lexus Climate Concierge
( P.278)
“AUTO”: Set automatic mode on/off
( P.285)
“Off”: Turn the fan off
“A/C”: Set cooling and dehumidification
function
NOTICE
■To prevent 12-volt battery discharge
Do not leave the air conditioning system
on longer than necessary when the engine <hybrid system> is off.
Air conditioning control screen
BE
A
B
C
D
E
F
G

284
-$@-$I@0.@0.&@ &&

5-3. Using the air conditioning system
“DUAL”: Adjust the temperature for driver
and passenger seats separately (“DUAL”
mode) ( P.286)
: Changing the fan speed setting
during the automatic mode operation
(Blower customization)
■Option control screen
Select on the sub menu to display
the option control screen.
The functions can be switched on and off.
When the function is on, the indicator illu-
minates on the screen.
Set Lexus Climate Concierge
( P.278)
Adjusting the temperature for
driver and passenger seats sepa-
rately (“DUAL” mode) ( P.286)
Cooling and dehumidification func-
tion
nanoe™* system on/off
Prevent ice from building up on the
windshield and wiper blades
(Windshield wiper de-icer) (if
equipped)
Removing pollen from the air (Pol-
len removal mode)
*: nanoe™ and the nanoe™ mark are
trademarks of Panasonic Corporation.
■Side display
Display the heated steering
wheel/seat heaters/seat ventilators
control screen (if equipped)
( P.288)
Adjust the left-hand side tempera-
ture setting
Adjust the fan speed setting
Adjust the right-hand side tem-
perature setting
Set cooling and dehumidification
function on/off
Adjust the temperature for the
driver’s and front passenger’s seats
separately (“DUAL” mode)
( P.286)
Select the air flow mode
■Windshield wiper de-icer (if equipped)
This feature is used to prevent ice from building up on the windshield and wiper
blades.
The windshield de-icer will automatically
turn off after approximately 15 minutes.
■Blower customization
Fan speed setting during the automatic
A
B
C
D
E
F
A
B
C
D
E
F
G

288
-$@-$I@0.@0.&@ &&

5-3. Using the air conditioning system
*: If equipped
■Main display
Using the touchpad of the Remote
Touch, select the button on the screen.
to can be adjusted by perform-
ing the following operations.
Flick operation: Move the pointer to
the desired item and flick the touchpad
up or down.
The item can be adjusted by one level.
Trace operation: After selecting the
desired item, trace the pad surface.
The item can be adjusted by the amount
that you trace.
Trace operation cannot be used while driv-
ing.
Heated steering wheel*/seat
heaters/seat ventilators
Heated steering wheel
Warms up the grip of the steering
wheel
 Seat heaters
Warm up the seat upholstery
 Seat ventilators
Maintain good air flow on the seat
upholstery by blowing air from the
seats
Press the “MENU” button on the
Remote Touch and select “Climate”
to display the air conditioning con-
trol screen. Then, select on the
sub menu ( P.283) to display the
heated steering wheel/seat heat-
ers/seat ventilators control screen.
WARNING
■To prevent minor burn injuries
Care should be taken if anyone in the fol- lowing categories comes in contact with the steering wheel and seats when the
heater is on:
●Babies, small children, the elderly, the sick and the physically challenged
●Persons with sensitive skin
●Persons who are fatigued
●Persons who have taken alcohol or drugs that induce sleep (sleeping
drugs, cold remedies, etc.)
NOTICE
■To prevent damage to the seat heat- ers and seat ventilators
Do not put heavy objects that have an uneven surface on the seat and do not
stick sharp objects (needles, nails, etc.) into the seat.
■To prevent 12-volt battery discharge
Do not use the functions when the engine <hybrid system> is off.
Control screen
AC