ignition lexus LC500 2018 Owner's Guide

4
153
-$@-$I@0.@0.&@ &&

4
Driving
Driving
4-1. Before driving
Driving the vehicle..................... 154
Cargo and luggage .................... 161
Trailer towing ............................... 162
4-2. Driving procedures
Engine (ignition) switch (LC500)
......................................................... 163
Power (ignition) switch (LC500h)
......................................................... 167
EV drive mode (LC500h)...... 171
Automatic transmission (LC500)
......................................................... 173
Hybrid transmission (LC500h)
......................................................... 179
Turn signal lever ......................... 186
Parking brake .............................. 187
Brake Hold.................................... 189
4-3. Operating the lights and wipers
Headlight switch .......................... 191
Automatic High Beam ............. 193
Fog light switch ........................... 196
Windshield wipers and washer
......................................................... 196
4-4. Refueling
Opening the fuel tank cap...... 201
4-5. Using the driving support sys-
tems
Lexus Safety System+ ............. 203
PCS (Pre-Collision System) . 210
LKA (Lane-Keeping Assist) .. 218
RSA (Road Sign Assist).......... 226
Dynamic radar cruise control with
full-speed range ...................... 229
Cruise control ............................ 239
Driving mode select switch ... 242
Lexus parking assist-sensor .. 243
BSM (Blind Spot Monitor) .... 248
Active rear wing ........................ 259
Driving assist systems .............. 262
4-6. Driving tips
Hybrid vehicle driving tips
(LC500h).................................. 267
Winter driving tips .................... 269

163
4
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
Driving
4-2.Driving procedures
1Press the parking brake switch to
check that the parking brake is set.
( P.187)
Parking brake indicator will come on.
2Firmly depress the brake pedal.
and a message will be displayed on
the multi-information display.
If it is not displayed, the engine cannot be started.
3 Press the engine switch shortly and
firmly.
When operating the engine switch, one
short, firm press is enough. It is not neces- sary to press and hold the switch.
The engine will crank until it starts or for up to 30 seconds, whichever is less.
Continue depressing the brake pedal until the engine is completely started.
The engine can be started from any engine
switch mode.
■Engine switch illumination
According to the situation, the engine switch illumination operates as follows.
●When a door is opened, or the engine switch mode is changed from ACCES-SORY or IGNITION ON mode to off,
the engine switch illumination slowly blinks.
●When depressing the brake pedal with carrying the electric key on your person, the engine switch illumination rapidly
blinks.
●When the engine sw itch is in ACCES- SORY or IGNITION ON mode, the engine switch illumination illuminates.
■If the engine does not start
●The engine immobilizer system may not have been deactivated. ( P.70)
Contact any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer.
●If a message related to start-up is shown on the multi-information display, read the
message and follow the instructions.
■If the 12-volt battery is discharged
The engine cannot be started using the
smart entry & start system. Refer to P.393 to restart the engine.
Engine (ignition) switch
(LC500)
Performing the following opera-
tions when carrying the electronic
key on your person starts the
engine or changes engine switch
modes.
Starting the engine

165
4
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
Driving
1Stop the vehicle completely.
2 If the parking brake is in manual
mode, set the parking brake.
( P.187)
3 Shift the shift position to P.
( P.175)
Check that the shift position indicator
shows P. ( P.175)
4Press the engine switch.
The engine will stop, and the meter display will be extinguished (the shift position indi-
cator will be extinguished a few seconds after the meter display).
5 Check that “ACCESSORY” or
“IGNITION ON” is not shown on
the meter.
■Automatic P position selection function
 P.176
Modes can be changed by pressing
the engine switch with the brake pedal
released. (The mode changes each
time the switch is pressed.)
NOTICE
■Symptoms indicating a malfunction with the engine switch
If the engine switch seems to be operat- ing somewhat differently than usual, such as the switch sticking slightly, there may
be a malfunction. Contact any autho- rized Lexus retailer or Lexus authorized repairer, or any reliable repairer immedi-
ately.
Stopping the engine
WARNING
■Stopping the engine in an emergency
●If you want to stop the engine in an
emergency while driving the vehicle, press and hold the engine switch for more than 2 seconds, or press it briefly
3 times or more in succession. ( P.360) However, do not touch the engine
switch while driving except in an emer- gency. Turning the engine off while driving will not cause loss of steering
or braking control, however, power assist to the steering will be lost. This will make it more difficult to steer
smoothly, so you should pull over and stop the vehicle as soon as it is safe to do so.
●If the engine switch is operated while the vehicle is running, a warning mes-
sage is shown on the multi-information display and a buzzer sounds.
●When restarting the engine after an emergency shutdown, press the engine switch.
Changing engine switch modes

166
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
1Off
The emergency flashers can be used.
2ACCESSORY mode
Some electrical components such as the
audio system can be used.
“ACCESSORY” will be displayed on the
meter.
3 IGNITION ON mode
All electrical components can be used.
“IGNITION ON” will be displayed on the
meter.
■Auto power off function
If the vehicle is left in ACCESSORY mode for more than 20 minutes or IGNITION
ON mode (the engine is not running) for more than an hour with the shift position in P, the engine switch will automatically turn
off. However, this function cannot entirely prevent the 12-volt battery discharge. Do not leave the vehicle with the engine switch
in ACCESSORY or IGNITION ON mode for long periods of time when the engine is not running.
■When the shift control system malfunc-tions
When attempting to turn the engine switch off while there is a malfunction in the shift control system, the engine switch mode
may change to ACCESSORY mode. In this case, ACCESSORY mode may be turned off by applying the parking brake and press-
ing the engine switch again. If there is a mal- function in the system, have the vehicle inspected by any authorized Lexus retailer
or Lexus authorized repairer, or any reliable repairer immediately.
NOTICE
■To prevent 12-volt battery discharge
●Do not leave the engine switch in
ACCESSORY or IGNITION ON mode for long periods of time without the engine running.
●If “ACCESSORY” or “IGNITION
ON” is displayed on the meter, the engine switch is not off. Exit the vehicle after turning the engine switch off.

167
4
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
Driving
1Press the parking brake switch to
check that the parking brake is set.
( P.187)
Parking brake indicator will come on.
2Firmly depress the brake pedal.
and a message will be displayed on
the multi-information display.
If it is not displayed, the hybrid system can- not be started.
When the shift position is N, the hybrid sys- tem cannot start. Shift the shift position to P
when starting the hybrid system. ( P.182)
3Press the power switch shortly and
firmly.
When operating the power switch, one short, firm press is enough. It is not neces-
sary to press and hold the switch.
If the “READY” indicator turns on, the
hybrid system will operate normally.
Continue depressing the brake pedal until
the “READY” indicator is illuminated.
The hybrid system can be started from any
power switch mode.
4 Check that the “READY” indicator
is illuminated.
If the “READY” indicator changes from a flashing light to a solid light and the buzzer sounds, the hybrid system is starting nor-
mally. The vehicle will not move when the “READY” indicator is off.
The vehicle can move when the “READY” indicator is on even if the engine is stopped. (The gasoline engine starts or
stops automatically in accordance with the state of the vehicle.)
■Power switch illumination
According to the situation, the power switch illumination operates as follows.
●When a door is opened, or the power switch mode is changed from ACCES-SORY or ON mode to off, the power
switch illumination slowly blinks.
●When depressing the brake pedal with
carrying the electric key on your person, the power switch illumination rapidly blinks.
●When the power switch is in ACCES-SORY or ON mode, the power switch
illumination illuminates.
■If the hybrid system does not start
●The immobilizer system may not have
been deactivated. ( P.70) Contact any authorized Lexus retailer or Lexus authorized repairer, or any reliable
repairer.
●If a message related to start-up is shown
Power (ignition) switch
(LC500h)
Performing the following opera-
tions when carrying the electronic
key on your person starts the hybrid
system or changes power switch
modes.
Starting the hybrid system

169
4
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
Driving
switch off, please wait a few seconds before restarting the hybrid system.
■Customization
If the smart entry & start system has been deactivated in a customized setting, refer to P.389.
1 Stop the vehicle completely.
2 If the parking brake is in manual
mode, set the parking brake.
( P.187)
3 Shift the shift position to P.
( P.182)
Check that the shift position indicator shows P. ( P.181)
4Press the power switch.
The hybrid system will stop, and the meter display will be extinguished (the shift posi-tion indicator will be extinguished a few
seconds after the meter display).
5 Check that “ACCESSORY” or
“IGNITION ON” is not shown on
the meter.
■Automatic P position selection function
 P.182
WARNING
■When starting the hybrid system
Always start the hybrid system while sit- ting in the driver’s seat. Do not depress the accelerator pedal while starting the
hybrid system under any circumstances. Doing so may cause an accident result-ing in death or serious injury.
■Caution while driving
If hybrid system failure occurs while the vehicle is moving, do not lock or open the
doors until the vehicle reaches a safe and complete stop. Activati on of the steering lock in this circumstance may lead to an
accident, resulting in death or serious injury.
NOTICE
■When starting the hybrid system
If the hybrid system becomes difficult to start, have your vehicle checked by any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer immediately.
■Symptoms indicating a malfunction with the power switch
If the power switch seems to be operat- ing somewhat differently than usual, such
as the switch sticking slightly, there may be a malfunction. Contact any autho-rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer immedi- ately.
Stopping the hybrid system
WARNING
■Stopping the hybrid system in an emergency
●If you want to stop the hybrid system in an emergency while driving the vehi-cle, press and hold the power switch
for more than 2 seconds, or press it briefly 3 times or more in succession. ( P.360)
However, do not touch the power switch while driving except in an emer- gency. Turning the hybrid system off
while driving will not cause loss of steering or braking control, however, power assist to the steering will be lost.
This will make it more difficult to steer smoothly, so you should pull over and stop the vehicle as soon as it is safe to
do so.
●If the power switch is operated while the vehicle is running, a warning mes-sage is shown on the multi-information
display and a buzzer sounds.

170
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
Modes can be changed by pressing
the power switch with the brake pedal
released. (The mode changes each
time the switch is pressed.)
1 Off
The emergency flashers can be used.
2ACCESSORY mode
Some electrical components such as the
audio system can be used.
“ACCESSORY” will be displayed on the
meter.
3 ON mode
All electrical components can be used.
“IGNITION ON” will be displayed on the
meter.
■Auto power off function
If the vehicle is left in ACCESSORY mode
for more than 20 minutes or ON mode (the hybrid system is not operating) for more than an hour with the shift position in P, the
power switch will automatically turn off. However, this function cannot entirely pre-vent the 12-volt battery discharge. Do not
leave the vehicle with the power switch in ACCESSORY or ON mode for long peri-ods of time when the hybrid system is not
operating.
■When the shift control system malfunc- tions
When attempting to turn the power switch off while there is a malfunction in the shift control system, the power switch mode may
change to ACCESSORY mode. In this case, ACCESSORY mode may be turned off by applying the parking brake and press-
ing the power switch again. If there is a mal- function in the system, have the vehicle inspected by any authorized Lexus retailer
or Lexus authorized repairer, or any reliable repairer immediately.
WARNING
●When restarting the hybrid system after an emergency shutdown, press the power switch.
Changing power switch modes
NOTICE
■To prevent 12-volt battery discharge
●Do not leave the power switch in ACCESSORY or ON mode for long
periods of time without the hybrid sys- tem on.
●If “ACCESSORY” or “IGNITION
ON” is displayed on the meter, the power switch is not off. Exit the vehicle after turning the power switch off.

173
4
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
Driving
*1: To improve fuel efficiency and reduce
noise, set the shift position in D for nor-
mal driving. You can choose gear range
suitable for your driving situation by
operating the paddle shift switches.
*2: Any gear range can be fixed when driv-
ing in M mode.
■For the shift positions
●When the engine switch is off or in ACCESSORY mode, the shift position
cannot be changed.
●When the engine switch is in IGNITION
ON mode, the shift position can only be changed to N.
●When the engine is running, the shift position can be changed from P to D, N or R.
●The shift position can only be changed to
M directly from D.
In addition, if an attempt is made to change
the shift position by moving the shift lever or by pressing the P position switch in any of the following situations, the buzzer will
sound and the shifting operation will be dis- abled or the shift position will automatically change to N. When this happens, select an
appropriate shift position.
●Situations where the shifting operation
will be disabled: • When an attempt is made to change the shift position from P to another position
by moving the shift lever without depress- ing the brake pedal.• When an attempt is made to change the
shift position from P or N to M by moving the shift lever.• When the P position switch is pressed
while the vehicle is running.*1
●Situations where the shift position will automatically change to N:• When an attempt is made to select the R
position by moving the shift lever when
the vehicle is moving forward.*2
• When an attempt is made to select the D position by moving the shift lever when
the vehicle is moving in reverse.*3
• When the shift position is changed from R to M
●If N is selected while driving at a certain speed, even if the shift lever is not held in
the N position, the shift position changes to N. In this situation, the buzzer sounds and a confirmation message is displayed
on the multi-information display to inform the driver that the shift position has changed to N.
*1: Shift position may be changed to P when
driving at extremely low speeds.
*2: Shift position may be changed to R when
driving at low speeds.
*3: Shift position may be changed to D
when driving at low speeds.
■Reverse warning buzzer
When shifting into R, a buzzer will sound to inform the driver that the shift position is in
Automatic transmission
(LC500)
Select the shift position depending
on your purpose and situation.
Shift position purpose and func-
tion
Shift positionObjective or function
PParking the vehicle/start-
ing the engine
RReversing
N
Neutral
(Condition in which the
power is not transmitted)
DNormal driving*1
MM mode driving*2
( P.178)

176
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
■Shifting the shift position from P to
other positions
 While depressing the brake pedal
firmly, operate the shift lever. If the
shift lever is operated without
depressing the brake pedal, the
buzzer will sound and the shifting
operation will be disabled.
 When selecting the shift position,
make sure that the shift position has
been changed to the desired posi-
tion by checking the shift position
indicator provided on the instru-
ment cluster.
 The shift position cannot be
changed from P to M directly.
■Automatic P position selection function
In the following situations, the shift position is automatically changed to P.
●When pressing the engine switch with the vehicle stopped while the engine switch is
in IGNITION ON mode and the shift position is in a positi on other than P (after the shift position has changed to P, the
engine switch will turn off)*
●When the vehicle is stopped after the engine has been stopped in an emer-gency while driving
●When voltage of the 12-volt battery drops while the shift position is in a posi-
tion other than P
*: When the engine switch is pressed while
driving at extremely slow speeds, such as
immediately before stopping the vehicle,
the shift position may automatically
change to P. Make sure that the vehicle is
completely stopped before pressing the
engine switch.
■If the shift position cannot be shifted
from P
There is a possibility that the 12-volt battery
is discharged. Check the 12-volt battery in this situation. ( P.392)
WARNING
■P position switch
●Do not press the P position switch
while the vehicle is moving. If the P position switch is pressed when driving at very low speeds (for exam-
ple, directly before stopping the vehi- cle), the vehicle may stop suddenly when the shift position switches to P,
which could lead to an accident.
●In order to prevent the shift position from accidentally being changed, do not touch the P position switch when
not using them.
NOTICE
■Notes regarding shift lever and P position switch operation
Avoid repeatedly operating the shift lever and P position switch in quick suc-cession.
The system protection function may acti- vate and it will not be temporarily possi-
ble to shift the shift position other than P. If this happens, please wait for a while before attempting to change the shift
position again.

186
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
1Right turn
2 Lane change to the right (move the
lever partway and release it)
The right hand signals will flash 3 times.
3 Lane change to the left (move the
lever partway and release it)
The left hand signals will flash 3 times.
4 Left turn
If the turn signals do not stop flashing
after turning left or right, or if you want
to stop them flashing, operate the lever
in the opposite direction to either posi-
tion 2 or 3. If you move the lever to
either position 1 or 4, the selected turn
signals will flash.
■Turn signals can be operated when
The engine switch <p ower switch> is in
IGNITION ON mode <ON mode>.
■If the indicator flashes faster than usual
Check that a light bulb in the front or rear
turn signal lights has not burned out.
■If the turn signals stop flashing before a lane change has been performed
Operate the lever again.
■Customization
 P.423
Turn signal lever
Operating instructions