Seat lexus LC500 2018 Repair Manual

237
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
selected by using the paddle shift switch.
●Vehicle speed is at or above approxi-
mately 50 km/h (30 mph). However, when a preceding vehicle is detected, the dynamic radar cruise con-
trol with full-speed range can be set even if the vehicle speed is below approxi-mately 50 km/h (30 mph).
■Accelerating after setting the vehicle
speed
The vehicle can accelerate by operating the
accelerator pedal. After accelerating, the set speed resumes. Ho wever, during vehi- cle-to-vehicle distance control mode, the
vehicle speed may decrease below the set speed in order to maintain the distance to the preceding vehicle.
■When the vehicle stops while follow-up
cruising
●Pressing the +/RES switch while the vehi-
cle ahead stops will resume follow-up cruising if the vehicle ahead starts off within approximately 3 seconds after the
switch is pressed.
●If the vehicle ahead starts off within 3 sec-
onds after your vehicle stops, follow-up cruising will be resumed.
■Automatic cancelation of vehicle-to-
vehicle distance control mode
Vehicle-to-vehicle distance control mode is
automatically canceled in the following situ- ations.
●Actual vehicle speed falls below approxi-mately 40 km/h (25 mph) when there are no vehicles ahead.
●The preceding vehicle leaves the lane when your vehicle is following at a vehicle
speed below approximately 40 km/h (25 mph). Otherwise, the sensor can not properly detect the vehicle. (“CRUISE
NOT AVAILABLE No Preceding Vehi- cles” is displayed on the multi-information display.)
●VSC is activated.
●TRC is activated for a period of time.
●When the VSC or TRC system is turned
off.
●When snow mode is set.
●The sensor cannot detect correctly
because it is covered in some way.
●Pre-collision brakin g is activated.
●The parking brake is operated.
●The vehicle is stopped by system control on a steep incline.
●The following are detected when the vehicle has been stopped by system con-trol:
• The driver is not wearing a seat belt. • The driver’s door is opened.• The vehicle has been stopped for about 3
minutes
If vehicle-to-vehicle distance control mode
is automatically canceled for any other rea-
son, there may be a malfunction in the sys-
tem. Contact any authorized Lexus retailer
or Lexus authorized repairer, or any reliable
repairer.
■Automatic cancelation of constant speed control mode
Constant speed control mode is automati- cally canceled in the following situations:
●Actual vehicle speed is more than
approximately 16 km/h (10 mph) below the set vehicle speed.
●Actual vehicle speed falls below approxi-mately 40 km/h (25 mph).
●VSC is activated.
●TRC is activated for a period of time.
●When the VSC or TRC system is turned off.
●Pre-collision brakin g is activated.
If constant speed control mode is automati-
cally canceled for any other reason, there
may be a malfunction in the system. Con-
tact any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer.
■If “Radar Cruise Control Unavailable” is
shown on the multi-information display
The radar cruise control system cannot be
used temporarily. Use the system when it

5
273
-$@-$I@0.@0.&@ &&

5
Interior features
Interior features
5-1. Remote Touch
Remote Touch ............................ 274
5-2. Lexus Climate Concierge
Lexus Climate Concierge..... 278
5-3. Using the air conditioning system
Automatic air conditioning system
........................................................ 280
Heated steering wheel/seat heat-
ers/seat ventilators................ 288
5-4. Using the interior lights
Interior lights list.......................... 291
5-5. Using the storage features
List of storage features ........... 293
Trunk features............................. 295
5-6. Using the other interior features
Other interior features ........... 297
ERA-GLONASS...................... 299

278
-$@-$I@0.@0.&@ &&

5-2. Lexus Climate Concierge
5-2.Lexus Climate Concierge
Select
The indicator on the Lexus Climate Con-
cierge control screen illuminates, and the
automatic air conditioning system, seat
heaters and ventilators, and heated steer-
ing wheel operate in automatic mode.
If any of the system is operated manually,
the indicator turns off. However, all other
functions continue to operate in automatic
mode.
■When using the Lexus Climate Con- cierge
Lexus Climate Concierge can be operated on the sub function menu or option control screen. ( P.283)
■Automatic air conditioning system
( P.280)
The temperature can be adjusted indi-
vidually for the driver seat and passen-
ger seat.
■Seat heaters and ventilators
( P.288)
Heating or ventilation is automatically
selected according to the set tempera-
ture of the air conditioning system, the
outside temperature, etc.
The seat heater and ventilator of the
front passenger seat operate in auto-
matic mode if a passenger is detected.
■Heated steering wheel (if
equipped) ( P.288)
Heated steering wheel operates auto-
matically according to the set tempera-
ture of the air conditioning system, the
outside temperature, etc.
Lexus Climate Concierge
The seat heaters, seat ventilators
and heated steering wheel (if
equipped) are each automatically
controlled according to the set
temperature of the air conditioning
system, the outside and cabin tem-
perature, etc. Lexus Climate Con-
cierge allows a comfortable
condition to be maintained without
adjusting each system.
Press the “MENU” button on the
Remote Touch and select “Climate”
to display the air conditioning con-
trol screen. Then, select on the
sub menu ( P.283) to display the
Lexus Climate Concierge control
screen.
Turning on Lexus Climate Con-
cierge
Operation of each system

279
5
-$@-$I@0.@0.&@ &&

5-2. Lexus Climate Concierge
Interior features
■Seat heater/ventilator operation
When automatic mode is selected using the
seat heater/ventilato r switch, passenger detection is not performed.

283
5
-$@-$I@0.@0.&@ &&

5-3. Using the air conditioning system
Interior features
■Main control screen
Using the touchpad of the Remote
Touch, select the button on the screen.
to can be adjusted by perform-
ing the following operations.
Flick operation: Move the pointer to
the desired item and flick the touchpad
up or down.
The item can be adjusted by one level.
Trace operation: After selecting the
desired item, trace the pad surface.
The item can be adjusted by the amount
that you trace.
Trace operation cannot be used while driv-
ing.
Sub menu
Selecting the sub menu item to switch the
main screen.
: Display the air conditioning control
screen
: Display the heated steering
wheel/seat heater/seat ventilator control
screen (if equipped)
: Display the Lexus Climate Con-
cierge control screen
: Display the option control screen
Adjust the left-hand side tempera-
ture setting
Adjust the fan speed setting
Select the air flow mode
: Air flows to the upper body
: Air flows to the upper body and
feet
: Air flows to the feet
: Air flows to the feet and the wind-
shield defogger operates
Adjust the right-hand side tem-
perature setting
Function on/off indicators
When the function is on, the indicator illu-
minates on the control screen.
Sub function menu
When the sub function button on the
Remote Touch is pressed, the following
functions can be switched on and off.
: Set Lexus Climate Concierge
( P.278)
“AUTO”: Set automatic mode on/off
( P.285)
“Off”: Turn the fan off
“A/C”: Set cooling and dehumidification
function
NOTICE
■To prevent 12-volt battery discharge
Do not leave the air conditioning system
on longer than necessary when the engine <hybrid system> is off.
Air conditioning control screen
BE
A
B
C
D
E
F
G

284
-$@-$I@0.@0.&@ &&

5-3. Using the air conditioning system
“DUAL”: Adjust the temperature for driver
and passenger seats separately (“DUAL”
mode) ( P.286)
: Changing the fan speed setting
during the automatic mode operation
(Blower customization)
■Option control screen
Select on the sub menu to display
the option control screen.
The functions can be switched on and off.
When the function is on, the indicator illu-
minates on the screen.
Set Lexus Climate Concierge
( P.278)
Adjusting the temperature for
driver and passenger seats sepa-
rately (“DUAL” mode) ( P.286)
Cooling and dehumidification func-
tion
nanoe™* system on/off
Prevent ice from building up on the
windshield and wiper blades
(Windshield wiper de-icer) (if
equipped)
Removing pollen from the air (Pol-
len removal mode)
*: nanoe™ and the nanoe™ mark are
trademarks of Panasonic Corporation.
■Side display
Display the heated steering
wheel/seat heaters/seat ventilators
control screen (if equipped)
( P.288)
Adjust the left-hand side tempera-
ture setting
Adjust the fan speed setting
Adjust the right-hand side tem-
perature setting
Set cooling and dehumidification
function on/off
Adjust the temperature for the
driver’s and front passenger’s seats
separately (“DUAL” mode)
( P.286)
Select the air flow mode
■Windshield wiper de-icer (if equipped)
This feature is used to prevent ice from building up on the windshield and wiper
blades.
The windshield de-icer will automatically
turn off after approximately 15 minutes.
■Blower customization
Fan speed setting during the automatic
A
B
C
D
E
F
A
B
C
D
E
F
G

286
-$@-$I@0.@0.&@ &&

5-3. Using the air conditioning system
2Press the outside/recirculated air
mode switch to switch to automatic
air intake mode.
The air conditioning system automatically
switches between outside air and recircu-
lated air modes.
3Adjust the temperature setting.
4 To stop the operation, press the off
switch or select “Off” on the sub
function menu. ( P.283)
If the fan speed setting or air flow
modes are operated, the automatic
mode indicator goes off. However,
automatic mode for functions other
than that operated is maintained.
■Using automatic mode
Fan speed is adjusted automatically accord-
ing to the temperature setting and the
ambient conditions.
Therefore, the fan may stop for a while until
warm or cool air is ready to flow immedi-
ately after the automatic mode switch is
pressed or “AUTO” is selected.
Cool air may blow around the upper body
even when the heater is on due to sunlight.
■Windshield fog detection function
When automatic mode is set, the humidity
sensor detects fog on the windshield and
controls the air conditioning system to pre-
vent fog.
■Automatic mode for air intake control
In automatic mode, the system detects
exhaust gas and other pollutants and auto-
matically switches between outside air and
recirculated air modes.
When the dehumidification function is off,
and the fan is operating, turning automatic
mode on will activate the dehumidification
function.
To turn on the “DUAL” mode, perform
any of the following procedures:
 Select “DUAL” on the sub function
menu. ( P.283)
 Select “DUAL” on the option con-
trol screen.
 Adjust the passenger’s side tem-
perature setting.
The indicator on the main control screen
comes on when the “DUAL” mode is on.
NOTICE
■Humidity sensor
In order to detect fog on the windshield,
a sensor which monitors the temperature
of the windshield, the surround humidity,
etc. is installed.
Follow these points to avoid damaging
the sensor:
●Do not disassemble the sensor
●Do not spray the glass cleaner on the
sensor or subject it to strong impacts
●Do not stick anything on the sensor
Adjusting the temperature for
driver and passenger seats sepa-
rately (“DUAL” mode)

288
-$@-$I@0.@0.&@ &&

5-3. Using the air conditioning system
*: If equipped
■Main display
Using the touchpad of the Remote
Touch, select the button on the screen.
to can be adjusted by perform-
ing the following operations.
Flick operation: Move the pointer to
the desired item and flick the touchpad
up or down.
The item can be adjusted by one level.
Trace operation: After selecting the
desired item, trace the pad surface.
The item can be adjusted by the amount
that you trace.
Trace operation cannot be used while driv-
ing.
Heated steering wheel*/seat
heaters/seat ventilators
Heated steering wheel
Warms up the grip of the steering
wheel
 Seat heaters
Warm up the seat upholstery
 Seat ventilators
Maintain good air flow on the seat
upholstery by blowing air from the
seats
Press the “MENU” button on the
Remote Touch and select “Climate”
to display the air conditioning con-
trol screen. Then, select on the
sub menu ( P.283) to display the
heated steering wheel/seat heat-
ers/seat ventilators control screen.
WARNING
■To prevent minor burn injuries
Care should be taken if anyone in the fol- lowing categories comes in contact with the steering wheel and seats when the
heater is on:
●Babies, small children, the elderly, the sick and the physically challenged
●Persons with sensitive skin
●Persons who are fatigued
●Persons who have taken alcohol or drugs that induce sleep (sleeping
drugs, cold remedies, etc.)
NOTICE
■To prevent damage to the seat heat- ers and seat ventilators
Do not put heavy objects that have an uneven surface on the seat and do not
stick sharp objects (needles, nails, etc.) into the seat.
■To prevent 12-volt battery discharge
Do not use the functions when the engine <hybrid system> is off.
Control screen
AC

289
5
-$@-$I@0.@0.&@ &&

5-3. Using the air conditioning system
Interior features
Adjust the seat ventilator fan speed
level
The seat ventilator can be adjusted in 3 lev-
els.
When the seat ventilator is operated, the
fan speed level is displayed on the screen.
Adjust the seat heater temperature
level
The seat heater can be adjusted in 3 levels.
When the seat heater is operated, the tem-
perature level is displayed on the screen.
Adjust the heated steering wheel
temperature level
The heated steering wheel can be adjusted
in 2 levels.
When the heated steering wheel is oper-
ated, the temperature level is displayed on
the screen.
Automatic mode on/off indicators
When the automatic mode is on, the indi-
cator illuminates on the screen.
Sub function menu
When the sub function button on the
Remote Touch is pressed, the following
functions can be set to automatic mode.
: Left-hand side seat heater/seat
ventilator
: Heated steering wheel
: Right-hand side seat heater/seat
ventilator
■Side display
Display the air conditioning control
screen ( P.283)
Adjust the seat heater temperature
level
Each time the switch is selected, the tem-
perature level and level indicator (orange)
change as follows:
AUTO  Hi  Mid  Lo  Off
Adjust the seat ventilator fan speed
level
Each time the switch is selected, the fan
speed level and level indicator (blue)
change as follows:
AUTO  Hi  Mid  Lo  Off
Adjust the heated steering wheel
temperature level
Each time the switch is selected, the tem-
perature level and level indicator change
as follows:
AUTO  Hi  Lo  Off
■The heated steering wheel, seat heaters and seat ventilators can be used when
The engine switch <p ower switch> is in IGNITION ON mode <ON mode>.
■Air conditioning system-linked control mode
When the seat ventilator fan speed level is Hi, the seat ventilator fan speed becomes
A
B
C
D
E
A
B
C
D

290
-$@-$I@0.@0.&@ &&

5-3. Using the air conditioning system
higher according to the fan speed of the air conditioning system.
■Customization
Steering wheel heating preference in auto- matic mode and the automatic mode set-tings for the seat heaters and ventilators can
be changed. (Customizable features: P.423)
WARNING
■To prevent overheating and minor burn injuries
Observe the following precautions when using the seat heaters.
●Do not cover the seat with a blanket or
cushion when using the seat heater.
●Do not use seat heater more than nec- essary.