steering lexus LC500 2018 Repair Manual

363
7
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
When trouble arisesIn the following situations, it is not pos-
sible to be towed by another vehicle
using cables or chains, as the rear
wheels may be locked due to the park-
ing lock. Contact any authorized Lexus
retailer or Lexus authorized repairer,
or any reliable repairer or commercial
towing service.
 There is a malfunction in the shift
control system. ( P.166, 170, 381)
 There is a malfunction in the engine
immobilizer system <immobilizer
system>. ( P.70)
 There is a malfunction in the smart
entry & start system. ( P.389)
 The 12-volt battery is discharged.
( P.392)
The following may indicate a problem
with your transmission. Contact any
authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer or commercial towing service
before towing.
 LC500: The engine is running but
the vehicle does not move.
 LC500h: The hybrid system warn-
ing message is shown on the multi-
information display and the vehicle
does not move.
 The vehicle makes an abnormal
sound.
Do not tow with a sling-type truck to
prevent body damage.
NOTICE
■To prevent damage to the vehicle when towing using a wheel-lift type truck
●Do not tow the vehicle from the rear
when the engine switch <power switch> is off. The steering lock mecha-nism is not strong enough to hold the
front wheels straight.
●When raising the vehicle, ensure ade- quate ground clearance for towing at the opposite end of the raised vehicle.
Without adequate clearance, the vehi- cle could be damaged while being towed.
■To prevent damage to the vehicle
when towing with a sling-type truck
Do not tow with a sling-type truck, either from the front or rear.
■To prevent damage to the vehicle during emergency towing
Do not secure cables or chains to the
suspension components.
Situations when it is not possible
to be towed by another vehicle
Situations when it is necessary to
contact dealers before towing
Towing with a sling-type truck

364
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
From the front
Use a towing doll y under the rear
wheels.
From the rear
Use a towing doll y under the front
wheels.
If your vehicle is transported by a flat-
bed truck, it should be tied down at the
locations shown in the illustration.
If you use chains or cables to tie down
your vehicle, the angles shaded in
black must be 45°.
Do not overly tighten the tie downs or
the vehicle may be damaged.
If a tow truck is not available in an
emergency, your vehicle may be tem-
porarily towed using cables or chains
secured to the emergency towing eye-
lets. This should only be attempted on
hard surfaced roads for short distances
at under 30 km/h (18 mph).
A driver must be in the vehicle to steer
and operate the brakes. The vehicle’s
wheels, drive train, axles, steering and
brakes must be in good condition.
Towing with a wheel-lift type
truck
Using a flatbed truck
Emergency towing

365
7
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
When trouble arises
To have your vehicle towed by another
vehicle, the towing eyelet must be
installed to your vehicle. Install the tow-
ing eyelet using the following proce-
dure.
1 Take out the towing eyelet.
( P.339)
2 Remove the eyelet cover using a
flathead screwdriver.
To protect the bodywork, place a rag between the screwdriver and the vehicle body as shown in the illustration.
3 Insert the towing eyelet into the
hole and tighten partially by hand.
4 Tighten down the towing eyelet
securely using a wheel nut wrench
or hard metal bar.
5 Securely attach cables or chains to
the towing eyelet.
Take care not to damage the vehicle body.
6 Enter the vehicle being towed and
start the engine <hybrid system>.
If the engine <hybrid system> does not start, turn the engine switch <power
switch> to IGNITION ON mode <ON mode>.
7 Shift the shift position to N and
release the parking brake.
■While towing
If the engine is not running <hybrid system is off>, the power assist for the brakes and
steering will not function, making steering and braking more difficult.
■Wheel nut wrench
Wheel nut wrench is installed in trunk. ( P.339)
Emergency towing procedure

370
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
■Electric power steering system warning light (warning buzzer)
■PCS warning light
Warning
lightWarning light/Details/Actions
(red)
or
(yellow)
Indicates a malfunction in the EPS (Electric Power Steering) system
 Have the vehicle inspected by any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer immediately.
Warning
lightWarning light/Details/Actions
 When the warning light flashes (and a buzzer sounds):
Indicates a malfunction in the PCS
 Have the vehicle inspected by any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer immediately.
 When the warning light flashes (and a buzzer does not sound):
Indicates that the PCS is temporarily unavailable, possibly due to either of
the following:
 An area around the radar sensor or camera sensor being dirty or covered
with condensation, ice, stickers, etc.
 Clear the dirt, condensation, ice, stickers, etc. (P.208)
 Radar sensor or camera sensor operational conditions (such as tempera-
ture etc.) being not met
 Driving is possible in this case. The PCS will be enabled if the opera-
tional conditions (such as temperature etc.) are met again.
 When the warning light is illuminated:
Either the VSC system or PCS is disabled or both are disabled.
 To enable the PCS, enable both the VSC system and PCS. (P.212,
263)

375
7
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
When trouble arises
■High coolant temperature warning light (warning buzzer)*
*: This light illuminates on the multi-information display.
■Front passenger detection sensor, seat belt reminder and warning buzzer
●If luggage is placed on a front passenger seat, the front passenger detection sensor may cause the warning light to flash and the warning buzzer to sound even if a passenger is not
sitting in the seat.
●If a cushion is placed on the seat, the sensor may not detect a passenger, and the warning
light may not operate properly.
■If the malfunction indicator lamp comes on while driving
The malfunction indicator lamp w ill come on if the fuel tank becomes completely empty. If
the fuel tank is empty, refuel the vehicle immediately. The malfunction indicator lamp will go off after several trips.
If the malfunction indicator lamp does not go off, contact any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer as soon as possible.
■Electric power steering system warning light (warning buzzer)
When the 12-volt battery charge becomes insufficient or the voltage temporarily drops, the electric power steering system warning lig ht may come on and the warning buzzer may sound.
■Tire pressure warning light
When a malfunction occurs in the tire pressure warning system, the tire pressure warning light blinks to warn the driver. However, if the warning light blinks for 1 minute, and then
remains illuminated, maki ng it difficult to determine whether the warning light is blinking, turn the engine switch <power switch> fr om off to IGNITION ON mode <ON mode> and check if the warning light blinks.
■When the tire pressure warning light comes on
Carry out the following procedure after the tire temperature has lowered sufficiently.
●Check the tire inflation pressure and adjust to the appropriate level.
●If the warning light does not go out even after several minutes, check that the tire inflation
pressure is at the specified level and carry out initialization. ( P.335)
The warning light may come on again if the above operations are conducted without first
allowing the tire temperature to lower sufficiently.
■The tire pressure warning light may come on due to natural causes
The tire pressure warning light may come on du e to natural causes such as natural air leaks
and tire inflation pressure changes caused by temperature. In this case, adjusting the tire inflation pressure will turn off the warning light (after a few minutes).
Warning
lightWarning light/Details/Actions
Indicates that the engine coolant temperature increases
 Stop and check. (P.400, 403)

376
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
■Conditions that the tire pressure warning system may not function properly
 P.330
■If the tire pressure warning light frequently comes on after blinking for 1 minute
If the tire pressure warning lig ht frequently comes on after blinking for 1 minute when the engine switch <power switch> is turned to IGNITION ON mode <ON mode>, have it
checked by any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer.
■Warning buzzer
In some cases, the buzzer may not be heard due to being in a noisy location or audio sound.
WARNING
■If both the ABS and the brake system warning lights remain on
Stop your vehicle in a safe place immediately and contact any authorized Lexus retailer
or Lexus authorized repairer, or any reliabl e repairer. The vehicle will become extremely unstable during braking, and the ABS system may fail, which could cause an accident resulting in death or serious injury.
■When the electric power steering system warning light comes on
When the light comes on yellow, the assist to the power steering is restricted. When the
light comes on red, the assist to the power st eering is lost and handling operations of the steering wheel become extremely heavy. When steering wheel operations are heavier than usual, grip the steering wheel firmly and operate it using more force than usual.
■If the tire pressure warning light comes on
Be sure to observe the following precautions. Failure to do so could cause a loss of vehi-
cle control and result in death or serious injury.
●Decelerate to the lowest appropriate speed as soon as possible. Do not drive over 80 km/h (50 mph).
●Check and adjust the tire inflation pressure immediately.
●If the tire pressure warning light comes on ev en after tire inflation pressure adjustment, it is probable that you have a flat tire. Have the flat tire replaced by nearest authorized
Lexus retailer or Lexus authorized repairer, or any reliable repairer.
●Avoid abrupt maneuvering and braking. If the vehicle tires deteriorate, you could lose control of the steering wheel or the brakes.
■If a blowout or sudden air leakage should occur
The tire pressure warning system may not activate immediately.

381
7
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
When trouble arises
Power was turned off due to the automatic power off function. Next time when starting the hybrid system, operate the hybrid system for approximately 5 minutes to recharge the 12-volt battery.
■If a message that indicates the need for the shift lever operation is shown
To prevent the shift lever from being operated incorrectly or the vehicle from moving unex- pectedly, a message that requires shifting the shift lever may be shown on the multi-informa-
tion display. In that case, follow the instru ction of the message and shift the shift lever.
■If “Front Camera Unavailable” or “Front Camera Vision Blocked Clean and Demist Windshield” is shown
The following systems may be suspended un til the problem shown in the message is resolved.
●PCS
●LKA
●Dynamic radar cruise cont rol with full-speed range
●Automatic High Beam
■If “Engine Stopped Steering Power Low” (LC500) or “Hybrid System Stopped Steer- ing Power Low” (LC500h) is shown
The steering wheel may become extremely heavy. If the steering wheel becomes heavier than usual when operating, hold firmly and operate using more force than usual.
■If “Warming Up Maximum Vehicle Speed: 110km/h” is shown (LC500h)
The transmission is being warmed up and the ve hicle is unable to be driven over 110 km/h (65 mph). Wait until the transmission warms up.
■If “Stop the vehicle in a safe place Shift to P position” is shown (LC500h)
There may be a malfunction in the hybrid system or the shift position may be shifted to N for a long time. Immediately stop the vehicle and contact any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer.
■If “Oil Maintenance Required Soon” is shown (LC500h)
The engine oil is scheduled to be changed. Check the engine oil, and change if necessary.
After changing the engine oil, the message should be reset. ( P.321)
■If “Engine Oil Level Low Add or Replace” is shown
The engine oil level is low. Check the level of engine oil, and add if necessary. This message
may appear if the vehicle is stopped on a slope. Move the vehicle to a level surface and check to see if the message disappears.
■If a message that indicates the need for referring to Owner’s Manual is shown
●If any of the following messages is shown on the multi-information display, follow the instructions.• “Engine Coolant Temp High” ( P.403, 403)
•“Battery low” ( P.392) • “Transmission Fluid Temp High” ( P.174, 180)
●If any of the following messages is shown on the multi-information display, it may indicate a malfunction. Have the vehicle inspected by any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer immediately.
• “Entry & Start System Malfunction”

385
7
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
When trouble arises
One of the following may be the cause
of the problem:
 The electronic key may not be func-
tioning properly. ( P.390)
 There may not be sufficient fuel in
the vehicle’s tank.
Refuel the vehicle. ( P.201)
 The engine may be flooded.
Try to restart the engine again fol-
lowing correct starting procedures.
( P.163)
 There may be a malfunction in the
engine immobilizer system.
( P.70)
 There may be a malfunction in the
shift control system.* ( P.166)
 There may be a malfunction in the
steering lock system.
*: It may not be possible to shift the shift
position from P.
One of the following may be the cause
of the problem:
 The 12-volt battery may be dis-
charged. ( P.392)
 The 12-volt battery terminal con-
nections may be loose or corroded.
( P.326)
The engine starting system may be
malfunctioning due to an electrical
problem such as electronic key battery
depletion or a blown fuse. However, an
interim measure is available to start the
engine.
One of the following may be the cause
of the problem:
 One or both of the 12-volt battery
terminals may be disconnected.
( P.326)
 The 12-volt battery may be dis-
charged. ( P.392)
 There may be a malfunction in the
If the engine will not start
(LC500)
If the engine will not start even
though correct starting procedures
are being followed ( P.163), con-
sider each of the following points:
The engine will not start even
though the starter motor oper-
ates normally.
The starter motor turns over
slowly, the interior lights and
headlights are di m, or the horn
does not sound or sounds at a low
volume.
The starter motor does not turn
over
The starter motor does not turn
over, the interior lights and head-
lights do not turn on, or the horn
does not sound.

386
-$@-$I@0.@0.&@ &&

7-2. Steps to take in an emergency
steering lock system.
Contact any authorized Lexus retailer or
Lexus authorized repairer, or any reliable
repairer if the problem cannot be repaired,
or if repair procedures are unknown.
When the engine does not start, the
following steps can be used as an
interim measure to start the engine if
the engine switch is functioning nor-
mally. Do not use this starting proce-
dure except in cases of emergency.
1 Press the parking brake switch to
check that the parking brake is set.
( P.187)
Parking brake indicator will come on.
2Turn the engine switch to ACCES-
SORY mode.
3 Press and hold the engine switch
for about 15 seconds while
depressing the brake pedal firmly.
Even if the engine can be started using
the above steps, the system may be
malfunctioning. Have the vehicle
inspected by any authorized Lexus
retailer or Lexus authorized repairer,
or any reliable repairer.
One of the following may be the cause
of the problem:
 The electronic key may not be func-
tioning properly. ( P.390)
 There may not be sufficient fuel in
the vehicle’s tank.
Refuel the vehicle. ( P.201)
 There may be a malfunction in the
immobilizer system. ( P.70)
 There may be a malfunction in the
shift control system.* ( P.170)
 There may be a malfunction in the
steering lock system.
 The hybrid system may be malfunc-
tioning due to an electrical problem
such as electronic key battery
depletion or a blown fuse. However,
depending on the type of malfunc-
tion, an interim measure is available
to start the hybrid system.
*: It may not be possible to shift the shift
position from P.
Starting the engine in an emer-
gency
If the hybrid system will not
start (LC500h)
Reasons for the hybrid system not
starting vary depending on the situ-
ation. Check the following and per-
form the appropriate procedure:
The hybrid system will not start
even though the correct starting
procedure is being followed.
( P.167)

418
-$@-$I@0.@0.&@ &&

8-1. Specifications
*: Your Lexus vehicle is filled with “Toyota Genuine Differential Gear Oil” at the factory.
Use Lexus approved “Toyota Genuine Differentia l Gear Oil” or an equivalent of match-
ing quality to satisfy the above specification. Please contact any authorized Lexus retailer
or Lexus authorized repairer, or any reliable repairer for further details.
*1: Minimum pedal clearance when depressed with a force of 500 N (51.0 kgf, 112.4 lbf)
while the engine is running <h ybrid system is operating>.
When performing the brake pedal inspection, also be sure to check that the brake sys-
tem warning light is not illuminated when the en gine is running <hybrid system is operat-
ing>. (If the brake system warning light is illuminated, refer to P.368)
*2: Make sure to confirm that the brake system wa rning light (yellow) does not illuminate. (If
the brake system warning ligh t illuminates, refer to P.373)
Differential
Oil capacity0.85 L (0.90 qt., 0.75 Imp. qt.)
Oil type and viscosity
Without LSD (Limited Slip Differential)
Toyota Genuine Differential gear oil LT 75W-85 GL-
5 or equivalent*
With LSD (Limited Slip Differential)
Toyota Genuine Differential gear oil LX 75W-85 GL-
5 or equivalent*
Brakes
Pedal clearance*1132 mm (5.2 in.) Min.
Pedal free play1.0 - 6.0 mm (0.04 - 0.24 in.)
Brake pad wear limit1.0 mm (0.04 in.)
Parking brake indicator*2
When pushing the parking br ake switch for 1 to 4 sec-
onds: comes on
When pulling the pa rking brake switch for 1 to 4 sec-
onds: turns off
Fluid typeSAE J1703 or FMVSS No. 116 DOT 3,
SAE J1704 or FMVSS No. 116 DOT 4
Steering
Free playLess than 30 mm (1.2 in.)