wing lexus LC500 2018 Manual PDF

160
-$@-$I@0.@0.&@ &&

4-1. Before driving
NOTICE
●When driving over bumps in the road, drive as slowly as possible to avoid damaging the wheels, underside of the
vehicle, etc.
■If you get a flat tire while driving
A flat or damaged tire may cause the fol-
lowing situations. Hold the steering wheel firmly and gradually depress the brake pedal to slow down the vehicle.
●It may be difficult to control your vehi-
cle.
●The vehicle will make abnormal sounds or vibrations.
●The vehicle will lean abnormally.
Information on what to do in case of a flat tire ( P.384)
■When encountering flooded roads
Do not drive on a road that has flooded after heavy rain etc. Doing so may cause the following serious damage to the vehi-
cle:
●Engine stalling
●Short in electrical components
●Engine damage caused by water immersion
In the event that you drive on a flooded road and the vehicle is flooded, be sure
to have any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer check the following:
●Brake function
●Changes in quantity and quality of oil
and fluid used for the engine, transmis- sion, differentials, etc.
●Lubricant condition for the propeller shaft, bearings and suspension joints
(where possible), and the function of all joints, bearings, etc.
If the shift control system is damaged by flooding, it may not be possible to shift
the shift position to P, or from P to other positions. In this case, contact any autho-rized Lexus retailer or Lexus authorized
repairer, or any reliable repairer immedi- ately.
■When parking the vehicle
Always set the parking brake, and shift the shift position to P. Failure to do so may cause the vehicle to move or the
vehicle may accelerate suddenly if the accelerator pedal is accidentally depressed.

161
4
-$@-$I@0.@0.&@ &&

4-1. Before driving
Driving
Cargo and luggage
Take notice of the following infor-
mation about storage precautions,
cargo capacity and load:
WARNING
■Things that must not be carried in the trunk
The following things may cause a fire if loaded in the trunk:
●Receptacles containing gasoline
●Aerosol cans
■Storage precautions
Observe the following precautions. Failure to do so may prevent the pedals from being depressed properly, may
block the driver’s vision, or may result in items hitting the driver or passengers, possibly causing an accident.
●Stow cargo and luggage in the trunk
whenever possible.
●Do not place cargo or luggage in or on the following locations.
• At the feet of the driver
• On the front passenger or rear seats
(when stacking items)
• On the package tray
• On the instrument panel
• On the dashboard
• In front of Center Display
●Secure all items in the occupant com-
partment.
■Load and distribution
●Do not overload your vehicle.
●Do not apply loads unevenly. Improper loading may cause deterio-
ration of steering or braking control which may cause death or serious injury.

162
-$@-$I@0.@0.&@ &&

4-1. Before driving
Trailer towing
Lexus does not recommend towing
a trailer with your vehicle. Lexus
also does not recommend the
installation of a tow hitch or the use
of a tow hitch carrier for a wheel-
chair, scooter, bicycle, etc. Your
vehicle is not designed for trailer
towing or for the use of tow hitch
mounted carriers.

163
4
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
Driving
4-2.Driving procedures
1Press the parking brake switch to
check that the parking brake is set.
( P.187)
Parking brake indicator will come on.
2Firmly depress the brake pedal.
and a message will be displayed on
the multi-information display.
If it is not displayed, the engine cannot be started.
3 Press the engine switch shortly and
firmly.
When operating the engine switch, one
short, firm press is enough. It is not neces- sary to press and hold the switch.
The engine will crank until it starts or for up to 30 seconds, whichever is less.
Continue depressing the brake pedal until the engine is completely started.
The engine can be started from any engine
switch mode.
■Engine switch illumination
According to the situation, the engine switch illumination operates as follows.
●When a door is opened, or the engine switch mode is changed from ACCES-SORY or IGNITION ON mode to off,
the engine switch illumination slowly blinks.
●When depressing the brake pedal with carrying the electric key on your person, the engine switch illumination rapidly
blinks.
●When the engine sw itch is in ACCES- SORY or IGNITION ON mode, the engine switch illumination illuminates.
■If the engine does not start
●The engine immobilizer system may not have been deactivated. ( P.70)
Contact any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer.
●If a message related to start-up is shown on the multi-information display, read the
message and follow the instructions.
■If the 12-volt battery is discharged
The engine cannot be started using the
smart entry & start system. Refer to P.393 to restart the engine.
Engine (ignition) switch
(LC500)
Performing the following opera-
tions when carrying the electronic
key on your person starts the
engine or changes engine switch
modes.
Starting the engine

167
4
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
Driving
1Press the parking brake switch to
check that the parking brake is set.
( P.187)
Parking brake indicator will come on.
2Firmly depress the brake pedal.
and a message will be displayed on
the multi-information display.
If it is not displayed, the hybrid system can- not be started.
When the shift position is N, the hybrid sys- tem cannot start. Shift the shift position to P
when starting the hybrid system. ( P.182)
3Press the power switch shortly and
firmly.
When operating the power switch, one short, firm press is enough. It is not neces-
sary to press and hold the switch.
If the “READY” indicator turns on, the
hybrid system will operate normally.
Continue depressing the brake pedal until
the “READY” indicator is illuminated.
The hybrid system can be started from any
power switch mode.
4 Check that the “READY” indicator
is illuminated.
If the “READY” indicator changes from a flashing light to a solid light and the buzzer sounds, the hybrid system is starting nor-
mally. The vehicle will not move when the “READY” indicator is off.
The vehicle can move when the “READY” indicator is on even if the engine is stopped. (The gasoline engine starts or
stops automatically in accordance with the state of the vehicle.)
■Power switch illumination
According to the situation, the power switch illumination operates as follows.
●When a door is opened, or the power switch mode is changed from ACCES-SORY or ON mode to off, the power
switch illumination slowly blinks.
●When depressing the brake pedal with
carrying the electric key on your person, the power switch illumination rapidly blinks.
●When the power switch is in ACCES-SORY or ON mode, the power switch
illumination illuminates.
■If the hybrid system does not start
●The immobilizer system may not have
been deactivated. ( P.70) Contact any authorized Lexus retailer or Lexus authorized repairer, or any reliable
repairer.
●If a message related to start-up is shown
Power (ignition) switch
(LC500h)
Performing the following opera-
tions when carrying the electronic
key on your person starts the hybrid
system or changes power switch
modes.
Starting the hybrid system

171
4
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
DrivingTurns EV drive mode on/off
When EV drive mode is turned on, the EV
drive mode indicator will come on. Press-
ing the switch when in EV drive mode will
return the vehicle to normal driving (using
the gasoline engine and electric motor
[traction motor]).
■Situations in which EV drive mode can-
not be turned on
It may not be possible to turn EV drive
mode on in the following situations. If it can- not be turned on, a buzzer will sound and a message will be shown on the multi-infor-
mation display.
●The temperature of the hybrid system is
high.
The vehicle has been left in the sun, driven on a hill, driven at high speeds, etc.
●The temperature of the hybrid system is low. The vehicle has been left in temperatures
lower than about 0°C (32°F) for a long period of time etc.
●The gasoline engine is warming up.
●The hybrid battery (traction battery) is
low. The remaining battery level indicated in the “Energy monitor” display is low.
( P.104)
●Vehicle speed is high.
●The accelerator pedal is depressed firmly or the vehicle is on a hill etc.
●The windshield defogger is in use.
●When the shift position is in M.
■Switching to EV drive mode when the gasoline engine is cold
If the hybrid system is started while the gas- oline engine is cold, the gasoline engine will start automatically in order to warm up. In
this case, you will become unable to switch to EV drive mode.
To prevent gasoline engine warm up in order to reduce noises, start the hybrid sys-
tem without starting the gasoline engine, pressing the power switch with fully depressing the brake pedal and pressing
the EV drive mode switch.
■Automatic cancelation of EV drive
mode
When driving in EV drive mode, the gaso-
line engine may automatically restart in the following situations. When EV drive mode is canceled, a buzzer will sound and the EV
drive mode indicator will flash and go off.
EV drive mode (LC500h)
In EV drive mode, electric power is
supplied by the hybrid battery
(traction battery), and only the
electric motor (traction motor) is
used to drive the vehicle.
This mode allows you to drive in res-
idential areas early in the morning
and late at night, or in indoor park-
ing lots etc. without concern for
noises and gas emissions.
Operating instructions

173
4
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
Driving
*1: To improve fuel efficiency and reduce
noise, set the shift position in D for nor-
mal driving. You can choose gear range
suitable for your driving situation by
operating the paddle shift switches.
*2: Any gear range can be fixed when driv-
ing in M mode.
■For the shift positions
●When the engine switch is off or in ACCESSORY mode, the shift position
cannot be changed.
●When the engine switch is in IGNITION
ON mode, the shift position can only be changed to N.
●When the engine is running, the shift position can be changed from P to D, N or R.
●The shift position can only be changed to
M directly from D.
In addition, if an attempt is made to change
the shift position by moving the shift lever or by pressing the P position switch in any of the following situations, the buzzer will
sound and the shifting operation will be dis- abled or the shift position will automatically change to N. When this happens, select an
appropriate shift position.
●Situations where the shifting operation
will be disabled: • When an attempt is made to change the shift position from P to another position
by moving the shift lever without depress- ing the brake pedal.• When an attempt is made to change the
shift position from P or N to M by moving the shift lever.• When the P position switch is pressed
while the vehicle is running.*1
●Situations where the shift position will automatically change to N:• When an attempt is made to select the R
position by moving the shift lever when
the vehicle is moving forward.*2
• When an attempt is made to select the D position by moving the shift lever when
the vehicle is moving in reverse.*3
• When the shift position is changed from R to M
●If N is selected while driving at a certain speed, even if the shift lever is not held in
the N position, the shift position changes to N. In this situation, the buzzer sounds and a confirmation message is displayed
on the multi-information display to inform the driver that the shift position has changed to N.
*1: Shift position may be changed to P when
driving at extremely low speeds.
*2: Shift position may be changed to R when
driving at low speeds.
*3: Shift position may be changed to D
when driving at low speeds.
■Reverse warning buzzer
When shifting into R, a buzzer will sound to inform the driver that the shift position is in
Automatic transmission
(LC500)
Select the shift position depending
on your purpose and situation.
Shift position purpose and func-
tion
Shift positionObjective or function
PParking the vehicle/start-
ing the engine
RReversing
N
Neutral
(Condition in which the
power is not transmitted)
DNormal driving*1
MM mode driving*2
( P.178)

174
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
R.
■To protect the automatic transmission
If the automatic transmission fluid tempera-
ture is high, “Transmission Fluid Temp High See Owner’s Manual” will be displayed on the multi-information display and the vehi-
cle will go into transmission protection mode automatically. Have the vehicle inspected by any authorized Lexus retailer
or Lexus authorized repairer, or any reliable repairer.
■When driving with cruise control or dynamic radar cruise control with full-
speed range activated
Even when performing the following
actions with the intent of enabling engine braking, engine braking will not be acti-vated because cruise control or dynamic
radar cruise control with full-speed range will not be canceled.
●While driving in the D position, down-shifting to 9, 8, 7, 6, 5 or 4.
●When switching the driving mode to sport mode while driving in D position. ( P.242)
■Restraining sudden start (Drive-Start Control)
 P.155
■AI-SHIFT
The AI-SHIFT automatically selects the suit-
able gear according to driver performance and driving conditions.The AI-SHIFT automatically operates when
the shift position is in D. (Shifting the shift position to M cancels the function.)
■If a message about a shift operation is shown
To prevent the shift position from being selected incorrectly or the vehicle from
moving unexpectedly, the shift position may be changed automatically or operating the shift lever may be required. In this case,
change the shift positi on following the mes- sages on the multi-information display.
■After recharging/reconnecting the 12-volt battery
 P.325
■Customization
Settings (e.g. Reverse warning buzzer) can
be changed. (Customizable features: P.423)
WARNING
■When driving on slippery road sur- faces
Do not accelerate or shift the shift posi- tion suddenly.
Sudden changes in engine braking may cause the vehicle to spin or skid, resulting in an accident.
NOTICE
■Situations where shift control system
malfunctions are possible
If any of the following situations occur,
shift control system malfunctions are possible. Immediately stop the vehicle in a safe place on level ground, apply the
parking brake, and then contact any authorized Lexus retailer or Lexus authorized repairer, or any reliable
repairer immediately.
●When the warning message indicating the shift control system appears on the multi-information display.
●The display indicates that no shift posi-
tion is selected for more than a few seconds.

176
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
■Shifting the shift position from P to
other positions
 While depressing the brake pedal
firmly, operate the shift lever. If the
shift lever is operated without
depressing the brake pedal, the
buzzer will sound and the shifting
operation will be disabled.
 When selecting the shift position,
make sure that the shift position has
been changed to the desired posi-
tion by checking the shift position
indicator provided on the instru-
ment cluster.
 The shift position cannot be
changed from P to M directly.
■Automatic P position selection function
In the following situations, the shift position is automatically changed to P.
●When pressing the engine switch with the vehicle stopped while the engine switch is
in IGNITION ON mode and the shift position is in a positi on other than P (after the shift position has changed to P, the
engine switch will turn off)*
●When the vehicle is stopped after the engine has been stopped in an emer-gency while driving
●When voltage of the 12-volt battery drops while the shift position is in a posi-
tion other than P
*: When the engine switch is pressed while
driving at extremely slow speeds, such as
immediately before stopping the vehicle,
the shift position may automatically
change to P. Make sure that the vehicle is
completely stopped before pressing the
engine switch.
■If the shift position cannot be shifted
from P
There is a possibility that the 12-volt battery
is discharged. Check the 12-volt battery in this situation. ( P.392)
WARNING
■P position switch
●Do not press the P position switch
while the vehicle is moving. If the P position switch is pressed when driving at very low speeds (for exam-
ple, directly before stopping the vehi- cle), the vehicle may stop suddenly when the shift position switches to P,
which could lead to an accident.
●In order to prevent the shift position from accidentally being changed, do not touch the P position switch when
not using them.
NOTICE
■Notes regarding shift lever and P position switch operation
Avoid repeatedly operating the shift lever and P position switch in quick suc-cession.
The system protection function may acti- vate and it will not be temporarily possi-
ble to shift the shift position other than P. If this happens, please wait for a while before attempting to change the shift
position again.

178
-$@-$I@0.@0.&@ &&

4-2. Driving procedures
■Automatic deactivation of shift range selection in the D position
Shift range selection in the D position will be deactivated in the following situations:
●When the vehicle comes to a stop
●If the accelerator pedal is depressed for
more than a certain period of time
●When the shift lever is moved to D again
●When pressing and holding the “+” pad- dle shift switch
■Downshifting restriction warning
buzzer
To help ensure safety and driving perfor-
mance, downshifting operation may some- times be restricted. In some circumstances, downshifting may not be possible even
when the paddle shift switch is operated. (A buzzer will sound twice.)
To enter M mode, shift the shift position
to M. Gears can be selected by oper-
ating the paddle shift switches, allowing
you to drive in the gear of your choos-
ing.
1 Upshifting
2 Downshifting
The gear changes once every time the
paddle shift switch is operated.
The selected gear, from M1 to M10, will be
fixed and displayed in the meter.
When in the M position, the gear will
not change unless the paddle shift
switches are operated.
However, even when in the M position,
the gears will be automatically
changed in the following situation:
 When vehicle speed drops (down-
shift only).
 When it is necessary to protect the
engine or automatic transmission
when the engine coolant tempera-
ture is low, the automatic transmis-
sion fluid temperature is high or low,
or other reasons.
Also, the gear will not shift when the
vehicle speed is low, even if an upshift
operation is performed.
■Downshifting restriction warning
buzzer
To help ensure safety and driving perfor-
mance, downshifting operation may some- times be restricted. In some circumstances, downshifting may not be possible even
when the paddle shift sw itch is operated. (A buzzer will sound twice.)
The Gear Shift Indicator display is a
guide to help the driver achieve
improved fuel economy and reduced
exhaust emissions within limits of
engine performance.
Selecting gears in the M position
Gear Shift Indicator (if
equipped)