Engine cover lexus LC500 2018 Owner's Manual

124
-$@-$I@0.@0.&@ &&

3-2. Opening, closing and locking the doors and trunk
■Battery-saving function
The battery-saving function will be acti-
vated in order to prevent the electronic key battery and the 12-volt battery from being discharged while the vehicle is not in opera-
tion for a long time.
●In the following situations, the smart entry
& start system may take some time to unlock the doors.• The electronic key has been left within
approximately 2 m (6 ft.) of the outside of the vehicle for 10 minutes or longer.• The smart entry & start system has not
been used for 5 days or longer.
●If the smart entry & start system has not
been used for 14 days or longer, the doors cannot be unlocked at the passen-ger door. In this case, push the depres-
sion on the front edge of the driver’s door handle, or use the wireless remote con-trol or mechanical key, to unlock the
doors.
■Turning an electronic key to battery- saving mode
When battery-saving mode is set, battery depletion is minimized by stopping the elec-
tronic key from receiving radio waves.
Press twice while pressing and
holding . Confirm that the elec-
tronic key indicator flashes 4 times.
While the battery-saving mode is set, the smart entry & start system cannot be used. To cancel the function, press any of the elec-
tronic key buttons.
■Conditions affecting operation
The smart entry & star t system uses weak radio waves. In the following situations, the
communication between the electronic key and the vehicle may be affected, preventing
the smart entry & start system, wireless remote control and engine immobilizer sys-tem <immobilizer syst em> from operating
properly. (Ways of coping: P.389)
●When the electronic key battery is
depleted
●Near a TV tower, electric power plant,
gas station, radio station, large display, airport or other facility that generates strong radio waves or electrical noise
●When carrying a portable radio, cellular phone, cordless phone or other wireless
communication device
●When the electronic key is in contact
with, or is covered by the following metal- lic objects• Cards to which aluminum foil is attached
• Cigarette boxes that have aluminum foil inside• Metallic wallets or bags
•Coins • Hand warmers made of metal• Media such as CDs and DVDs
●When other wireless keys (that emit radio waves) are being used nearby
●When carrying the electronic key
together with the following devices that emit radio waves• Another vehicle’s electronic key or a
wireless key that emits radio waves • Personal computers or personal digital assistants (PDAs)
• Digital audio players • Portable game systems
●If window tint with a metallic content or metallic objects are attached to the rear window
●When the electronic key is placed near a battery charger or electronic devices
■Note for the entry function
●Even when the electronic key is within the effective range (detection areas), the sys-
tem may not operate properly in the fol- lowing cases:• The electronic key is too close to the win-
dow or outside door handle, near the ground, or in a high place when the doors are locked or unlocked.

146
-$@-$I@0.@0.&@ &&

3-4. Adjusting the steering wheel and mirrors
The height of the rear view mirror can
be adjusted to suit your driving pos-
ture.
Adjust the height of the rear view mir-
ror by moving it up and down.
Responding to the level of brightness
of the headlights of vehicles behind, the
reflected light is automatically
reduced.
Turn the automatic anti-glare function
mode on/off
When the automatic anti-glare function is
in ON mode, the indicator illuminates.
The function will set to ON mode each
time the engine switch <power switch> is
turned to IGNITION ON mode <ON
mode>.
Pressing the button turns the function to
OFF mode. (The indicator also turns
off.)
■To prevent sensor error
To ensure that the sensors operate properly, do not touch or cover them.
Inside rear view mirror
The rear view mirror’s position can
be adjusted to enable sufficient
confirmation of the rear view.
Adjusting the height of rear view
mirror
WARNING
■Caution while driving
Do not adjust the position of the mirror while driving.
Doing so may lead to mishandling of the vehicle and cause an accident, resulting in death or serious injury.
Anti-glare function
A
A

245
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
• When the Lexus parking assist-sensor is turned off once and turned on again• When the engine switch <power switch>
is turned off once and turned to IGNI- TION ON mode <ON mode> again
■If “Clean Parking Assist Sensor” is dis-played on the multi-information display
A sensor may be dirty or covered with snow or ice. In such cases, if it is removed from
the sensor, the system should return to nor- mal.
Also, due to the sensor being frozen at low temperatures, a malfunction display may appear or an obstacle may not be detected.
If the sensor thaws out, the system should return to normal.
■If “Parking Assist Malfunction” or “Park-ing Assist Malfunction Visit Your
Dealer” is displayed on the multi-infor- mation display
There is a malfunction and the device may not be working properly.
Have the vehicle inspected by any autho- rized Lexus retailer or Lexus authorized repairer, or any reliable repairer.
■Sensor detection information
●The sensor’s detection areas are limited
to the areas around the vehicle’s front and rear bumpers.
●Certain vehicle conditions and the sur-rounding environment may affect the ability of the sensor to correctly detect
obstacles. Particular instances where this may occur are listed below.• There is dirt, snow or ice on the sensor.
(Wiping the sensors will resolve this problem.)• The sensor is frozen. (Thawing the area
will resolve this problem.)
In especially cold weather, if a sensor is fro-
zen the screen may show an abnormal dis-
play, or obstacles may not be detected.
• The sensor is covered in any way.
• The vehicle is leaning considerably to one side.• On an extremely bumpy road, on an
incline, on grav el, or on grass. • The vicinity of the vehicle is noisy due to
vehicle horns, motorcycle engines, air brakes of large vehicles, or other loud noises producing ultrasonic waves.
• There is another vehicle equipped with parking assist sensor in the vicinity.• The sensor is splashed with water or
heavy rain. • The vehicle is equipped with a fender pole or wireless antenna.
• Towing eyelets are installed. • The bumper or sensor receives a strong impact.
• The vehicle is approaching a tall or curved curb.• In harsh sunlight or intense cold weather.
• The area directly under the bumpers is not detected.• If obstacles draw too close to the sensor.
• A non-genuine Lexus suspension (low- ered suspension etc.) is installed.• People may not be detected if they are
wearing certain types of clothing.
In addition to the examples above, there are
instances in which, because of their shape,
signs and other objects may be judged by
the sensor to be closer than they are.
●The shape of the obstacle may prevent the sensor from detecting it. Pay particu-
lar attention to the following obstacles: • Wires, fences, ropes, etc.• Cotton, snow and other materials that
absorb sound waves • Sharply-angled objects•Low obstacles
• Tall obstacles with upper sections pro- jecting outwards in the direction of your vehicle
●The following situations may occur during use.
• Depending on the shape of the obstacle and other factors, the detection distance may shorten, or detection may be impos-
sible. • Obstacles may not be detected if they are too close to the sensor.
• There will be a short delay between obstacle detection and display. Even at slow speeds, there is a possibility that the
obstacle will come within the sensor’s detection areas before the display is shown and the warning beep sounds.

258
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
■Conditions under which the RCTA func- tion will not detect a vehicle
The RCTA function is not designed to detect the following types of vehicles and/or objects:
●Vehicles approaching from directly behind
●Vehicles backing up in a parking space next to your vehicle
●Vehicles that the sensors cannot detect due to obstructions
●Guardrails, walls, signs, parked vehicles
and similar stationary objects*
●Small motorcycles, bicycles, pedestrians,
etc.*
●Vehicles moving away from your vehicle
●Vehicles approaching from the parking
spaces next to your vehicle*
*: Depending on the conditions, detection
of a vehicle and/or object may occur.
■Conditions under wh ich the RCTA func-
tion may not function correctly
●The RCTA function may not detect vehi-
cles correctly in the following situations: • When the sensor is misaligned due to a strong impact to the sensor or its sur-
rounding area • When mud, snow, ice, a sticker, etc. is covering the sensor or surrounding area
on the rear bumper • When driving on a road surface that is wet with standing water during bad
weather, such as heavy rain, snow, or fog • When multiple vehicles are approaching with only a small gap between each vehi-
cle • When a vehicle is approaching at high speed
• When a towing eyelet is installed to the rear of the vehicle.• When backing up on a slope with a sharp
change in grade
• When backing out of a shallow angle
parking spot
• Immediately after the RCTA function is
turned on • Immediately after the engine <hybrid sys-tem> is started with the RCTA function on
• When the sensors cannot detect a vehi- cle due to obstructions
●Instances of the RCTA function unneces-sarily detecting a vehicle and/or object may increase in the following situations:
• When a vehicle passes by the side of your

265
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
■EPS, VGRS and DRS operation sound
When the steering wheel is operated, a
motor sound (whirring sound) may be heard. This does not indicate a malfunction.
■Automatic reactivation of TRC and VSC systems
After turning the TRC and VSC systems off, the systems will be automatically re-
enabled in the following situations:
●When the engine switch <power switch>
is turned off
●If only the TRC system is turned off, the
TRC will turn on when vehicle speed increases
If both the TRC and VSC systems are turned off, automatic re-enabling will not occur when vehicle speed increases.
■Secondary Collision Brake operating
conditions
The vehicle speed is approximately 10 km/h
(6 mph) or more and the airbag sensor detects a collision. (The Secondary Colli-sion Brake will not operate when the vehicle
speed is below approximately 10 km/h [6 mph].)
■Secondary Collision Brake automatic
cancellation
The Secondary Collision Brake is automati-
cally canceled in the following situations:
●The vehicle speed drops below approxi-
mately 10 km/h (6 mph)
●A certain amount of time elapses during
operation
●The accelerator pedal is depressed a
large amount
■If “Check Secondary Collision Brake system” is displayed on the multi-infor-mation display
The system may be malfunctioning. Have the vehicle inspected at any authorized
Lexus retailer or Lexus authorized repairer, or any reliable repairer.
■Reduced effectiveness of the EPS sys-tem
The effectiveness of the EPS system is
reduced to prevent the system from over- heating when there is frequent steering input over an extended period of time. The
steering wheel may feel heavy as a result. Should this occur, refrain from excessive steering input or stop the vehicle and turn
the engine <hybrid system> off. The EPS sys- tem should return to normal within 10 min-utes.
■Operating conditions of emergency
brake signal
When the following three conditions are
met, the emergency brake signal will oper- ate:
●The emergency flashers are off.
●Actual vehicle speed is over 55 km/h
(35 mph).
●The brake pedal is depressed in a manner
that cause the system to judge from the vehicle deceleration that this is a sudden braking operation.
■Automatic system cancelation of emer-
gency brake signal
The emergency brake sign al will turn off in
any of the following situations:
●The emergency flashers are turned on.
●The brake pedal is released.
●The system judges from the vehicle deceleration that is not a sudden braking
operation.
WARNING
■The ABS does not operate effectively when
●The limits of tire gripping performance have been exceeded (such as exces-
sively worn tires on a snow covered road).
●The vehicle hydroplanes while driving at high speed on wet or slick roads.

297
5
-$@-$I@0.@0.&@ &&

5-6. Using the other interior features
Interior features
5-6.Using the other interior features
1To set the visor in the forward posi-
tion, flip it down.
2 To set the visor in the side position,
flip down, unhook, and swing it to
the side.
Open the cover.
The light turns on when the cover is
opened.
The GPS clock’s time is automatically
adjusted by utilizing GPS time infor-
mation.
For details, refer to the “NAVIGA-
TION SYSTEM OWNER’S MAN-
UAL”.
Please use as a power supply for elec-
tronic goods that use less than 12
VDC/10 A (power consumption of
120 W).
Open the lid.
■The power outlet can be used when
The engine switch <p ower switch> is in ACCESSORY or IGNITION ON mode
<ON mode>.
Other interior features
Sun visors
Vanity mirrors
NOTICE
■To prevent 12-volt battery discharge
Do not leave the lights on longer than necessary when the engine <hybrid sys-
tem> is off.
Clock
Power outlet

312
-$@-$I@0.@0.&@ &&

6-2. Maintenance
6-2.Maintenance
■Where to go for maintenance service?
In order to maintain your vehicle in the best possible condition, Lexus recommends that maintenance service operations as well as
other inspections and repairs be carried out by authorized Lexus retailer or Lexus authorized repairer, or any reliable repair-
ers. For repairs and services covered by your warranty, please visit an authorized Lexus retailer or repairer, who will use gen-
uine Lexus parts in repairing any difficulties you may encounter. There can also be advantages in utilizing authorized Lexus
retailers or repairers for non-warranty repairs and services, as members of the Lexus network will be able to expertly assist
you with any difficulties you may encounter.
Your Lexus retailer or Lexus authorized
repairer, or any reliable repairer will per- form all of the scheduled maintenance on your vehicle reliably and economically due
to their experience with Lexus vehicles.
Scheduled maintenance should be
performed at specified intervals
according to the maintenance sched-
ule.
For details about maintenance items and
schedules, refer to the “Lexus Service
Booklet” or “Lexus Warranty Booklet”.
What about do-it-yourself mainte-
nance?
Many of the maintenance items are easy to
do yourself if you have a little mechanical
ability and a few basic automotive tools.
Note, however, that some maintenance
tasks require special tools and skills. These
are best performed by qualified techni-
cians. Even if you’re an experienced do-it-
yourself mechanic, we recommend that
repairs and maintenance be conducted by
any authorized Lexus retailer or Lexus
authorized repairer, or any reliable
repairer. Any authorized Lexus retailer or
repairer will keep a record of maintenance,
which could be useful should you ever
require Warranty Service. Should you
choose to select a qualified and equipped
professional other than an authorized
Lexus repairer to service or maintain your
vehicle, we recommend that you request
that a record of maintenance be kept.
■Does your vehicle need repairs?
Be on the alert for changes in performance and sounds, and visual tip-offs that indicate
service is needed. Some important clues are:
●Engine missing, stumbling or pinging
Maintenance requirements
To ensure safe and economical driv-
ing, day-to-day care and regular
maintenance are essential. Lexus
recommends the following mainte-
nance:
WARNING
■If your vehicle is not properly main-
tained
Improper maintenance could result in
serious damage to the vehicle and possi- ble death or serious injury.
■Handling of the 12-volt battery
12-volt battery posts, terminals and related accessories contain lead and lead compounds which are known to
cause brain damage. Wash your hands after handling. ( P.325)
Scheduled maintenance
Do-it-yourself maintenance

326
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Pull the strap upwards to lift up the lug-
gage mat.
Make sure that the 12-volt battery ter-
minals are not corroded and that there
are no loose connections, cracks, or
loose clamps.
Terminals
Hold-down clamp
The meanings of each caution symbol
on the top of the 12-volt battery are as
follows:
WARNING
■How to recharge the 12-volt battery
Recharge at a current of 5 A or less and
make sure that the recharging period does not exceed a total of 12 hours.
■Emergency measures regarding electrolyte
●If electrolyte gets in your eyesFlush your eyes with clean water for at
least 15 minutes and get immediate medical attention. If possible, continue to apply water with a sponge or cloth
while traveling to the nearest medical facility.
●If electrolyte gets on your skinWash the affected area thoroughly. If
you feel pain or burning, get medical attention immediately.
●If electrolyte gets on your clothesIt can soak through clothing on to your
skin. Immediately take off the clothing and follow the procedure above if nec-essary.
●If you accidentally swallow electrolyte
Drink a large quantity of water or milk. Get emergency medical attention immediately.
NOTICE
■When recharging the 12-volt battery
Never recharge the 12-volt battery while the engine is running <hybrid system is operating>. Also, be sure all accessories
are turned off.
Removing the 12-volt battery
cover
Exterior
Caution symbols
No smoking, no naked
flames, no sparks
Shield eyes
A
B

347
6
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
Maintenance and care
ing your tires, check that the wheel
nuts are still tight after driving 1600
km (1000 miles).
 Be careful not to damage the alumi-
num wheels when using tire chains.
 Use only Lexus genuine balance
weights or equivalent and a plastic
or rubber hammer when balancing
your wheels.
1 Turn the engine switch <power
switch> off.
2 Open the glove box.
3 Remove the panel.
4 Unlock the filter cover ( ), pull
the filter cover out of the claws
( ), and remove the filter cover.
Air conditioning filter
The air conditioning filter must be
changed regularly to maintain air
conditioning efficiency.
Removing the air conditioning
filter
A
B

350
-$@-$I@0.@0.&@ &&

6-3. Do-it-yourself maintenance
1Turn the engine switch <power
switch> off.
2 Open the fuse box cover.
Engine compartment: type A fuse
box (LC500)
Left-hand drive vehicles:
Push the tab in and lift the lid off.
Right-hand drive vehicles:
Push the tab in and lift the lid off.
WARNING
■Removed battery and other parts
These parts are small and if swallowed by
a child, they can cause choking. Keep away from children. Failure to do so could result in death or serious injury.
■Certification for the electronic key
battery
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
NOTICE
■When replacing the battery
Use a screwdriver of appropriate size. Applying excessive force may deform or
damage the cover.
■For normal operation after replacing the battery
Observe the following precautions to prevent accidents:
●Always work with dry hands.Moisture may cause the battery to rust.
●Do not touch or move any other com-
ponent inside the remote control.
●Do not bend either of the battery ter- minals.
Checking and replacing
fuses
If any of the electrical components
do not operate, a fuse may have
blown. If this happens, check and
replace the fuses as necessary.
Checking and replacing fuses