roof lexus LC500 2018 Owner's Manual

37
1
-$@-$I@0.@0.&@ &&

1-1. For safe use
For safety and security
Front impact sensors
Side impact sensors (door)
The main SRS airbag system components are shown above. The SRS airbag sys-
tem is controlled by the airbag sensor assembly. As the airbags deploy, a chemical
reaction in the inflators quickly fills the airbags with non-toxic gas to help restrain
the motion of the occupants.
■If the SRS airbags deploy (inflate)
●Slight abrasions, burns, bruising etc., may be sustained from SRS airbags, due to the extremely high speed deployment (infla-
tion) by hot gases.
●A loud noise and white powder will be
emitted.
●Parts of the airbag module (steering
wheel hub, airbag cover and inflator) as well as the front seats, parts of the front and rear pillars, and roof side rails, may
be hot for several mi nutes. The airbag itself may also be hot.
●The windshield may crack.
●Vehicles with ERA-GLONASS: If the
SRS airbags deploy, the system is
designed to send an emergency call* to
the Public Safety Answering Point (PSAP), notifying them of the vehicle’s location (without needing to push the
“SOS” button) and an agent will attempt to speak with the occupants to ascertain the level of emergency and assistance
required. If the occupants are unable to communicate, the agent automatically treats the call as an emergency and helps
to dispatch the necessary emergency services. ( P.299)*: In some cases, the call cannot be made.
( P.300)
■SRS airbag deployment conditions (SRS
front airbags)
●The SRS front airbags will deploy in the
event of an impact that exceeds the set threshold level (the level of force corre- sponding to an approximately 20 - 30
km/h [12 - 18 mph] frontal collision with a fixed wall that does not move or deform).
However, this threshold velocity will be considerably higher in the following situa-
tions: • If the vehicle strikes an object, such as a parked vehicle or sign pole, which can
move or deform on impact • If the vehicle is involved in an underride collision, such as a collision in which the
front of the vehicle underrides, or goes under, the bed of a truck
●Depending on the type of collision, it is possible that only the seat belt preten-sioners will activate.
■SRS airbag deployment conditions (SRS
side and curtain shield airbags)
●The SRS side and curtain shield airbags
will deploy in the event of an impact that exceeds the set thresh old level (the level
of force corresponding to the impact force produced by an approximately 1500 kg [3300 lb.] vehicle colliding with
the vehicle cabin from a direction per- pendicular to the vehicle orientation at an approximate speed of 20 - 30 km/h [12 -
18 mph]).
●Both SRS curtain shield airbags may
deploy in the event of a severe side colli- sion.
●For Russia and Kazakhstan: Both SRS curtain shield airbags will deploy in the event of vehicle rollover.
●Both SRS curtain shield airbags may also deploy in the event of a severe frontal col-
lision.
■Conditions under which the SRS air- bags may deploy (inflate), other than a collision
The SRS front airbags and SRS curtain shield airbags may also deploy if a serious
P
Q

40
-$@-$I@0.@0.&@ &&

1-1. For safe use
●The portion of the front pillars, rear pillars or roof side rail garnishes (padding) con-taining the SRS curtain shield airbags
inside is scratched, cracked, or otherwise damaged.
WARNING
■SRS airbag precautions
Observe the following precautions
regarding the SRS airbags. Failure to do so may cause death or seri-ous injury.
●The driver and all passengers in the
vehicle must wear their seat belts properly.The SRS airbags are supplemental
devices to be used with the seat belts.
●The SRS driver airbag deploys with considerable force, and can cause
death or serious injury especially if the driver is very close to the airbag.Since the risk zone for the driver’s air-
bag is the first 50 - 75 mm (2 - 3 in.) of inflation, placing yourself 250 mm (10 in.) from your driver airbag provides
you with a clear margin of safety. This distance is measured from the center of the steering wheel to your breast-
bone. If you sit less than 250 mm (10 in.) away now, you can change your driving position in several ways:
• Move your seat to the rear as far as you can while still reaching the pedals
comfortably.
• Slightly recline the back of the seat.
Although vehicle designs vary, many drivers can achieve the 250 mm (10 in.) distance, even with the driver seat
all the way forward, simply by reclining the back of the seat somewhat. If reclining the back of your seat makes it
hard to see the road, raise yourself by using a firm, non-slippery cushion, or raise the seat if your vehicle has that
feature.
• If your steering wheel is adjustable, tilt it downward. This points the airbag toward your chest instead of your head
and neck.
The seat should be adjusted as recom-
mended above, while still maintaining
control of the foot pedals, steering wheel,
and your view of the instrument panel
controls.
●The SRS front passenger airbag also
deploys with considerable force, and can cause death or serious injury especially if the front passenger is very
close to the airbag. The front passen- ger seat should be as far from the air-bag as possible with the seatback
adjusted, so the front passenger sits upright.

41
1
-$@-$I@0.@0.&@ &&

1-1. For safe use
For safety and security
WARNING
●Improperly seated and/or restrained infants and children can be killed or seriously injured by a deploying airbag.
An infant or child who is too small to use a seat belt should be properly secured using a child restraint system.
Lexus strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly
restrained. The rear seats are safer for infants and children than the front pas-senger seat. ( P.48)
●Do not sit on the edge of the seat or
lean against the dashboard.
●Do not allow a child to stand in front of
the SRS front passenger airbag unit or sit on the knees of a front passenger.
●Do not allow the front seat occupants to hold items on their knees.
●Do not lean against the door, the roof side rail or the front, side and rear pil-
lars.
●Do not allow anyone to kneel on the
passenger seat toward the door or put their head or hands outside the vehi-cle.
●Do not attach anything to or lean any-thing against areas such as the dash-
board, steering wheel pad and lower portion of the instrument panel. These items can become projectiles
when the SRS driver, front passenger and knee airbags deploy.

42
-$@-$I@0.@0.&@ &&

1-1. For safe use
WARNING
●Do not attach anything to areas such as a door, windshield, side window, front or rear pillar and roof side rail.
●Do not hang coat hangers or other hard objects on the coat hooks. All of
these items could become projectiles and may cause death or serious injury, should the SRS curt ain shield airbags
deploy.
●If a vinyl cover is put on the area where the SRS knee airbag will deploy, be sure to remove it.
●Do not use seat accessories which
cover the parts where the SRS side air- bags inflate as they may interfere with inflation of the SRS airbags. Such
accessories may prevent the side air- bags from activating correctly, disable the system or cause the side airbags to
inflate accidentally, resulting in death or serious injury.
●Do not strike or apply significant levels of force to the area of the SRS airbag
components or the doors. Doing so can cause the SRS airbags to malfunction.
●Do not touch any of the component
parts immediately after the SRS air- bags have deployed (inflated) as they may be hot.
●If breathing becomes difficult after the
SRS airbags have deployed, open a door or window to allow fresh air in, or leave the vehicle if it is safe to do so.
Wash off any residue as soon as possi- ble to prevent skin irritation.
●If the areas where the SRS airbags are stored, such as the steering wheel pad
and front and rear pillar garnishes are damaged or cracked, have them replaced by any authorized Lexus
retailer or Lexus authorized repairer, or any reliable repairer.
■Modification and disposal of SRS air-bag system components
Do not dispose of your vehicle or per- form any of the following modifications
without consulting any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer. The SRS airbags
may malfunction or deploy (inflate) acci- dentally, causing death or serious injury.
●Installation, removal, disassembly and repair of the SRS airbags
●Repairs, modifications, removal or
replacement of the steering wheel, instrument panel, dashboard, seats or seat upholstery, front, side and rear pil-
lars, roof side rails, door panels, door trims or door speakers
●Modifications to the door panel (such
as making a hole in it)
●Repairs or modifications of the front fender, front bumper, or side of the occupant compartment
●Installation of a grille guard (bull bars,
kangaroo bar, etc.), snow plows, winches or roof luggage carrier
●Modifications to the vehicle’s suspen-sion system
●Installation of electronic devices such
as mobile two-way radios (RF-trans- mitter) and CD players

53
1
-$@-$I@0.@0.&@ &&

1-2. Child safety
For safety and security
WARNING
WARNING
■When installing a child restraint sys-
tem
●Only put a forward-facing child
restraint system on the front seat when unavoidable. When installing a for-
ward-facing child rest raint on the front passenger seat, move the seat as far back as possible. Failing to do so may
result in death or serious injury if the airbags deploy (inflate).
●Do not allow the child to lean his/her head or any part of his/her body
against the door or the area of the seat, front or rear pillars or roof side rails from which the SRS side airbags or
SRS curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the
SRS side and curtain shield airbags inflate, and the impact could cause death or serious injury to the child.
●When a junior seat is installed, always ensure that the shoulder belt is posi-
tioned across the center of the child’s shoulder. The belt should be kept away from the child’s neck, but not so that it
could fall off the child’s shoulder.
●Use child restraint system suitable to the age and size of the child and install it to the rear seat.

209
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
WARNING
●If the part of the windshield in front of the camera sensor is fogged up or covered with condensation or ice, use
the windshield defogger to remove the fog, condensation or ice. ( P.281)
●If water droplets cannot be properly removed from the area of the wind-
shield in front of the camera sensor by the windshield wipers, replace the wiper insert or wiper blade.
If the wiper inserts or wiper blades need to be replaced, contact any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer.
●Do not attach window tinting to the windshield.
●Replace the windshield if it is damaged
or cracked. If the windshield needs to be replaced, contact any authorized Lexus retailer
or Lexus authorized repairer, or any reliable repairer.
●Do not get the camera sensor wet.
●Do not allow bright lights to shine into the camera sensor.
●Do not dirty or damage the camera
sensor. When cleaning the inside of the wind-shield, do not allow glass cleaner to
contact the lens. Also, do not touch the lens. If the lens is dirty or damaged, contact
any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer.
●Do not subject the camera sensor to a
strong impact.
●Do not change the installation position or direction of the camera sensor or remove it.
●Do not disassemble the camera sen-
sor.
●Do not install an electronic device or device that emits strong electric waves
near the camera sensor.
●Do not modify any components of the vehicle around the camera sensor (inside rear view mirror, etc.) or ceiling.
●Do not attach any accessories that
may obstruct the camera sensor to the hood, front grille or front bumper. Contact any authorized Lexus retailer
or Lexus authorized repairer, or any reliable repairer for details.
●If a surfboard or other long object is to be mounted on the roof, make sure
that it will not obstruct the camera sen- sor.
●Do not modify the headlights or other lights.

268
-$@-$I@0.@0.&@ &&

4-6. Driving tips
Control and maintain the vehicle at a
constant speed. Before stopping at a
toll booth or similar, allow plenty of
time to release the accelerator and
gently apply the brakes. A greater
amount of electrical energy can be
regenerated when slowing down.
Use the air conditioning only when
necessary. Doing so can help reduce
excessive gasoline consumption.
In summer: When the ambient tem-
perature is high, use the recirculated
air mode. Doing so will help to reduce
the burden on the air conditioning sys-
tem and reduce fuel consumption as
well.
In winter: Because the gasoline engine
will not automatically cut out until it and
the interior of the vehicle are warm, it
will consume fuel. Also, fuel consump-
tion can be improved by avoiding over-
use of the heater.
Make sure to check the tire inflation
pressure frequently. Improper tire infla-
tion pressure can cause poor fuel
economy.
Also, as snow tires can cause large
amounts of friction, their use on dry
roads can lead to poor fuel economy.
Use tires that are appropriate for the
season.
Carrying heavy luggage will lead to
poor fuel economy. Avoid carrying
unnecessary luggage. Installing a large
roof rack will also cause poor fuel
economy.
Since the gasoline engine starts up and
cuts out automatically when cold,
warming up the engine is unnecessary.
Moreover, frequently driving short dis-
tances will cause the engine to repeat-
edly warm up, which can lead to excess
fuel consumption.
Highway driving
Air conditioning
Checking tire inflation pressure
Luggage
Warming up before driving

270
-$@-$I@0.@0.&@ &&

4-6. Driving tips
Perform the following according to the
driving conditions:
 Do not try to forcibly open a window
or move a wiper that is frozen. Pour
warm water over the frozen area to
melt the ice. Wipe away the water
immediately to prevent it from
freezing.
 When the outside door handle is
frozen, unlock the doors using the
wireless remote control. If the out-
side door handles remain retracted
and do not move even if the doors
are unlocked using the wireless
remote control, pour warm water
over the frozen area to melt the ice
and wipe away the water immedi-
ately to prevent it from freezing. The
outside door handle may not retract
due to ice, however, the outside
door handle will return to the nor-
mal position after the ice melts.
 To ensure proper operation of the
climate control system fan, remove
any snow that has accumulated on
the air inlet vents in front of the
windshield.
 Check for and remove any excess
ice or snow that may have accumu-
lated on the exterior lights, vehicle’s
roof, chassis, around the tires or on
the brakes.
 Remove any snow or mud from the
bottom of your shoes before getting
in the vehicle.
■To protect windshield wipers
 P.198
Accelerate the vehicle slowly, keep a
safe distance between you and the
vehicle ahead, and drive at a reduced
speed suitable to road conditions.
Park the vehicle and shift the shift posi-
tion to P without setting the parking
brake. The parking brake may freeze
up, preventing it from being released. If
the vehicle is parked without setting
the parking brake, make sure to block
the wheels.
Failure to do so may be dangerous
because it may cause the vehicle to
move unexpectedly, possibly leading to
an accident.
NOTICE
■Repairing or replacing snow tires
Request repairs or re placement of snow
tires from any authorized Lexus retailer or Lexus authorized repairer, or any reli-able repairer.
This is because the removal and attach- ment of snow tires affects the operation
of the tire pressure warning valves and transmitters.
Before driving the vehicle
When driving the vehicle
When parking the vehicle

304
-$@-$I@0.@0.&@ &&

6-1. Maintenance and care
6-1.Maintenance and care
Working from top to bottom, liber-
ally apply water to the vehicle body,
wheel wells and underside of the
vehicle to remove any dirt and dust.
 Wash the vehicle body using a
sponge or soft cloth, such as a
chamois.
 For hard-to-remove marks, use car
wash soap and rinse thoroughly with
water.
 Wipe away any water.
 Wax the vehicle when the water-
proof coating deteriorates.
If water does not bead on a clean surface,
apply wax when the vehicle body is cool.
■CFRP (Carbon Fiber Reinforced Plas- tic) part (if equipped)
●As the CFRP parts may change color if they are exposed to ultraviolet rays for
extended periods of time, Lexus recom- mends that your vehicle be stored in a place where it will not be exposed to
direct sunlight.
●Do not use wax that contains abrasives.
●Do not use automatic car washes as they may scratch the CFRP parts and damage
the paint.
■Self-restoring coat*
The vehicle body has a self-restoring coat-
ing that is resistant to small surface scratches caused in a car wash etc.
●The coating lasts for 5 to 8 years from when the vehicle is delivered from the plant.
●The restoration time differs depending on the depth of the scratch and outside tem-
perature. The restoration time may become shorter when the coating is warmed by
applying warm water.
●Deep scratches caused by keys, coins,
etc. cannot be restored.
●Do not use wax that contains abrasives.
*: CFRP parts (if equipped) do not have a
self-restoring coat.
■Cleaning the areas with metal accents
Do not use baking soda (sodium bicarbon-
ate) and wax that contains abrasives.
■Automatic car washes (vehicles without CFRP parts)
●Fold the mirrors before washing the vehi-cle. Start washing from the front of the vehicle. Make sure to extend the mirrors
before driving.
●Wash the vehicle with the active rear wing retracted. If the vehicle is washed with the active rear wing raised, depend-
ing on the type of automatic car wash, the brushes of the automatic car wash may become stuck on the active rear wing. In
this case, the active rear wing may not be washed very well or may even be scratched or damaged.
●Brushes used in automatic car washes may scratch the vehicle body and dam-
age the paint.
■High pressure car washes
●Do not allow the nozzles of the car wash
to come within close proximity of the win- dows.
●Before using the car wash, check that the fuel filler door on your vehicle is closed properly.
Cleaning and pr otecting the
vehicle exterior
Perform cleaning in a manner
appropriate to each component
and its material.
Cleaning instructions