ECO mode lexus LS400 1994 Gauges, Meters and Service Reminder Indicators / 1994 LS400: STARTING AND DRIVING

STARTING AND DRIVING
11 9

Keep your engine in good running order.
Malfunctions in the engine electrical system,
electronic ignition system / distributor ignition
system or fuel system could cause an extremely high
three-way catalytic converter temperature.

If the engine becomes difficult to start or stalls
frequently, take your vehicle in for a check-up as soon
as possible. Remember, your Lexus dealer knows
your vehicle and its three-way catalytic converter
system best.

To ensure that the three-way catalytic converter and
the entire emission control system operate properly,
your vehicle must receive the periodic inspections
required by the Lexus Maintenance Schedule.
ENGINE EXHAUST CAUTION
CAUTION:

Avoid inhaling the engine exhaust. It contains carbon
monoxide, which is a colorless and odorless gas. It can
cause unconsciousness or even death.

Make sure the exhaust system has no holes or loose
connections. The system should be checked from time
to time. If you hit something, or notice a change in the
sound of the exhaust, have the system checked
immediately.
Do not run the engine in a garage or enclosed area
except for the time needed to drive the vehicle in or out.
The exhaust gases cannot escape, making this a
particularly dangerous situation.

Do not remain for a long time in a parked vehicle with
the engine running. If it is unavoidable, however, do so
only in an unconfined area and adjust the heating or
cooling system to force outside air into the vehicle.

Keep the trunk lid closed while driving. An open or
unsealed trunk lid may cause exhaust gases to be
drawn into the vehicle. If you must drive with the trunk
lid open to accommodate a large object, close the
windows, open all the dashboard vents and have the
heating or cooling system deliver fresh air into the
vehicle by turning the fan to high speed with the air
intake control button in the OUTSIDE AIR mode.

To allow proper operation of your vehicle’s ventilation
system, keep the inlet grilles in front of the windshield
clear of snow, leaves, or other obstructions.

If you smell exhaust fumes in the vehicle, drive with the
windows open and the trunk lid closed. Have the cause
immediately located and corrected.

STARTING AND DRIVING
132
The indicator light shows the selector switch is in
“SPORT” position. When the indicator light is not on, this
means the selector switch is in “NORMAL” position.
When you turn the ignition key to the “ON” position, the
indicator lights will come on for two seconds.
HEIGHT CONTROL SYSTEM
(U. S. A. ONLY)
The height control system adjusts the vehicle height. This
adjustment is automatically made in response to the
driving conditions to provide good riding comfort and
stability in all driving conditions.
(a) Vehicle height adjustment
Push the selector switch to select one of the following modes:
“NORMAL” mode − For driving on roads with a normal
surface.
“HIGH” mode − For driving on rough roads which are
unsurfaced or continually bumpy.
To change the mode, push the selector switch.
“NORMAL” mode
The vehicle height remains at normal height at all driving
speeds.

STARTING AND DRIVING
133 “HIGH” mode
The vehicle height switches between the following two vehicle
heights according to the driving conditions:
Vehicle height
Driving condition
NormalHigh-speed driving
HighLow and medium speed driving
The indicator light shows the vehicle height is high.
When you turn the ignition key to the “ON” position, the
indicator light will come on for 2 seconds.
(b) Height control ON / OFF switch
OnOff
This switch is located inside the tool storage section on the left
side of the trunk compartment. Sliding the switch to the OFF
position will turn off the height control system. When the switch
is turned off, the “HI” display plinks.
NOTICE:
Before jacking up, towing or hoisting the vehicle, always
turn the height control ON / OFF switch to OFF. If this is
not done, the vehicle height automatic adjustment
function will operate, causing imbalance of the vehicle
and contact of the bumper, etc. with the road surface.
(c) Malfunction warning
If the “HI” display blinks when the height control ON / OFF
switch is turned on, there is a malfunction in the Lexus ride
control system or height control system.

STARTING AND DRIVING
134If the “HI” display is blinking and you suspect a malfunction,
first check that the height control ON / OFF switch is actually
turned on.
If you then confirm that the switch is blinking in the malfunction
mode, have the system checked by your Lexus dealer at the
first opportunity.
TRACTION CONTROL SYSTEM
The traction control system automatically controls
spinning of the rear wheels which may occur when
accelerating on slippery road surfaces, thus maintaining
vehicle stability and driving power to the rear wheels.
When you turn the ignition switch on, this system always
turns on. Leave the system on during ordinary driving so
that it can operate when needed. When traction control is
applied, the “TRAC” indicator / warning light blinks.
Vehicles without headlight cleaner
Vehicles with headlight cleaner
You can turn off the traction control system by pushing
the “TRAC-OFF-” switch. The “TRAC OFF”
indicator / warning light will then come on. Pushing the
“TRAC-OFF-” switch a second time turns the system back
on and extinguishes the “TRAC OFF” indicator / warning
light.
You may hear a slight clicking noise in the engine compartment
when the engine is started. This means that the traction control
system is in the self-check mode, and does not indicate
malfunction. When the traction control system is operating,
you may feel vibration of your vehicle, caused by operation of
the brakes. This indicates the system is functioning properly.
When getting the vehicle out of mud or new snow, etc. the
traction control system will operate to prevent the wheels from
spinning. Even though the accelerator pedal is fully depressed,
the engine speed will be restrained to a certain level.

STARTING AND DRIVING
135 CAUTION:
Under certain slippery road conditions, full stability of the
vehicle and power to the rear wheels cannot be
maintained, even though the traction control system is in
operation. In situations where the road surface is covered
with ice or snow, your vehicle should be fitted with snow
tires or tire chains and driven at a more cautious pace.
BRAKE SYSTEM
The tandem master cylinder brake system is a hydraulic
system with two separate sub-systems. If either sub-system
should fail, the other will still work. However, the pedal will be
harder to press, and your stopping distance will be longer.
Also, the brake system warning light may come on.
CAUTION:
Do not rely on a single brake system. Have your brakes
fixed immediately.
Brake booster
The brake booster uses engine vacuum to power-assist the
brakes. If the engine should quit while you are driving, you can
bring the vehicle to a stop with normal pedal pressure. There
is enough reserve vacuum for one or two stops but no more!
CAUTION:

Do not pump the brake pedal if the engine stalls. Each
push on the pedal uses up your vacuum reserve.
Even if the power assist is completely lost, the brakes
will still work. But you will have to push the pedal hard
− much harder than normal. And your braking distance
will be longer.
Anti-lock brake system
The anti-lock brake system is designed to prevent lock-up
of the wheels during sudden braking or braking on
slippery surfaces. This helps the vehicle remain steerable
and stable under these circumstances.
The system functions with normal pedal operation. When the
anti-lock function is in action, pulsation of the brake pedal may
occur, together with a characteristic noise. This indicates that
the system is functioning properly.
The anti-lock brake system comes into operation when the
vehicle is accelerating and the vehicle speed reaches
approximately 10 km / h (6 mph). It stops operating when the
vehicle is decelerating and the vehicle speed falls below
approximately 5 km / h (3 mph).
You may hear a sound in the engine compartment for a few
seconds just after the vehicle is started. This means that the
anti-lock brake system is in the self-check mode, and does not
indicate malfunction.
Even though the anti-lock brake system is operating, full
stability of the vehicle cannot be maintained for certain slippery
road conditions or high speed driving when cornering. Even
with the anti-lock brake system installed, it is still important, to
drive with all due care.