lexus LS400 1995 Electrical Components / 1995 LS400: IN CASE OF AN EMERGENCY

IN CASE OF AN EMERGENCY
169 Align the holes in the wheel with then bolts. Then lift up the
wheel and get at least the top bolt started through its hole.
Wiggle the tire and press it back over the other bolts.
Reinstall the wheel nuts and tighten them as much as you can
by hand. Press the tire back and see if you can tighten them
more.
9. Lower the vehicle completely and tighten the wheel
nuts.
Turn the jack handle counterclockwise to lower the vehicle.
Use only the wheel nut wrench to tighten the nuts. Do not use
other tools or any additional leverage other than your hands,
such as a hammer, pipe or your foot. Make sure the wrench is
securely engaged over the nut.
Tighten each nut a little at a time in the order shown. Repeat
the process until all the nuts are tight.
CAUTION
As soon as possible after changing wheels, have the
wheel nuts tightened by torque wrench at 103 N.m (10.5
kgf.m, 76 ft.lb.).
10. Reinstall the wheel ornament.
Put the wheel ornament into position and then tap it firmly with
the side or heel of your hand to snap it into place.
11. After changing the wheel, check the air pressure of the
replaced tire. Stow all the tools, jack and flat tire securely.
If the pressure of the replaced tire is low, drive slowly to the
nearest service station and fill to the correct pressure.
Do not forget to reinstall the tire valve cap as dirt and moisture
could get into the valve core and possible cause air leakage.
If the cap is missing, put a new one on as soon as possible.

IN CASE OF AN EMERGENCY
170This is the same procedure for changing or rotating your tires.
CAUTION
Before driving, make sure all the tools, jack and flat tire
are securely in place in their storage location to reduce
the possibility of personal injury during a collision or
sudden braking.
IF YOUR VEHICLE NEEDS TO BE
TOWED
If towing is necessary, we recommend you have it done by
your Lexus dealer or a commercial tow truck service.
Proper equipment will help ensure that your vehicle is not
damaged while being towed. Commercial operators are
generally aware of the state / provincial and local laws
pertaining to towing.
Your vehicle can be damaged if it is towed incorrectly. Although
most operators know the correct procedure, it is possible to
make a mistake. To avoid damage to your vehicle, make sure
the following few precautions are observed. If necessary, show
this page to the tow truck driver.
TOWING PRECAUTIONS:
Use a safety chain system for all towing, and abide by the
state / provincial and local laws. The wheels and axle on the
ground must be in good condition. If they are damaged, use a
towing dolly.

IN CASE OF AN EMERGENCY
171 1. Using flat bed truck
Lexus recommends this as the best method for your vehicle.
Tie down points
If your Lexus is transported by a flat bed, it should be tied
down at locations A and B as shown above.

IN CASE OF AN EMERGENCY
172
Rear emergency towing eyelets
NOTICE

Do not use the rear emergency towing eyelets.

For vehicles sold in U.S.A., before your vehicle is
transported by flat bed, the height control switch, if
so equipped, must be in the “HIGH” mode.

Tie down angle
If you use chains or wires to tie down your vehicle, the
angles shaded black must be at 45.

IN CASE OF AN EMERGENCY
173 2. Towing with wheel lift type truck

From front
Use a towing dolly under the rear wheels.
NOTICE
Never tow a vehicle with an automatic transmission
from the front with rear wheels on the ground, as this
may cause serious damage to the transmission.

From rear
Place the ignition key in the “ACC” position.
NOTICE
Do not tow with the key removed or in the “LOCK”
position, as the steering lock mechanism is not strong
enough to hold the front wheels straight.

IN CASE OF AN EMERGENCY
1743. Towing with a sling type truck

From front
Follow the instructions for towing from front in “2. Towing with
wheel lift type truck”.

From rear
NOTICE
Do not tow with a sling type truck. This may cause body
damage.
Emergency towing
If towing service is not available in an emergency, your
vehicle may be temporarily towed by a cable secured to
one of the eyelets under the front or rear of the vehicle.
A driver must be in the vehicle to steer it and operate the
brakes. Towing in this manner may be done only on
hard−surfaced roads for a short distance and at low speeds.
Also, the wheels, axles, drive train, steering and brakes must
all be in good condition.
Before towing, release the parking brake and put the
transmission in “N”. The ignition key must be in “ACC” (engine
off) or “ON” (engine running).
CAUTION
If the engine is not running, the power assist for the
brakes and steering will not work, so steering and
braking will be much harder than usual.

IN CASE OF AN EMERGENCY
175
IF YOU CANNOT SHIFT
AUTOMATIC TRANSMISSION
SELECTOR LEVER
If you cannot shift the selector lever, use the shift lock
override button as follows:
1
Turn the ignition key to “LOCK” or “ACC”. Make sure the
parking brake is applied. Pry up the cover with a
flat−bladed screwdriver or equivalent.
2
Insert your finger, the screwdriver or equivalent into the
hole to push down the shift lock override button. You can
shift the selector lever while pushing the button.
For your safety, keep the brake pedal depressed.
Be sure to have the system checked by your Lexus dealer as
soon as possible.

IN CASE OF AN EMERGENCY
176
IF YOU LOSE YOUR KEYS OR LOCK
YOURSELF OUT
If you need a replacement key, contact your Lexus dealer.
See the suggestion given in “Keys” on page 8.
If your keys are locked in the vehicle and you cannot get a
duplicate, many Lexus dealers can assist you. If you must
break a window to get in, we suggest breaking the smallest
side window because it is the least expensive to replace. Be
extremely cautious to avoid cuts from the glass.