engine lexus LS400 1995 Gauges, Meters and Service Reminder Indicators / 1995 LS400: STARTING AND DRIVING

STARTING AND DRIVING
136
(e) Good driving practice

If the transmission repeatedly upshifts and downshifts
between the third and overdrive gears when climbing a
gentle slope, shift the selector lever to the “3” position. Be
sure to shift the selector lever to the “D” position after
climbing the slope.

When towing a trailer, in order to maintain efficient engine
braking and electrical charging performance, do not use
overdrive. The selector lever must be in the “3” position.
CAUTION
Always keep your foot on the brake pedal while stopped
with the engine running. This prevents the vehicle from
creeping.
NOTICE
Do not hold the vehicle on an upgrade with the
accelerator pedal. This can cause the transmission to
overheat. Always use the brake pedal or parking brake.
(f) If you cannot shift the selector lever
If you cannot shift the selector ever even though the brake
pedal is depressed, use the shift lock override button. For
instructions, see “If you cannot shift automatic transmission
selector lever” on page 175.
(g) If the “ECT PWR” indicator light flashes
If the “ECI PWR” indicator light flashes, contact your Lexus
dealer as soon as possible. There may be trouble in the
transmission system.
CRUISE CONTROL
The cruise control allows you to cruise the vehicle at a
desired speed over 40 km / h (25 mph) with your foot off the
accelerator pedal.
Your cruising speed can be maintained although a slight speed
change may occur when driving up or down a gradient, within
the limits of engine performance. On steeper hills, a great
speed change will occur so it is better to drive without the cruise
control.
When the cruse control is on, the driving pattern of the
automatic transmission is fixed in the normal position,
regardless of the position of the selector switch.

STARTING AND DRIVING
137
CAUTION

To help maintain maximum control of your vehicle,
do not use the cruise control when driving in heavy
or varying traffic, or on slippery (rainy, icy or
snow−covered) or winding roads.

Avoid vehicle speed increases when driving
downhill. If the vehicle speed is too fast in relation to
the cruise control set speed, cancel the cruise
control then downshift the transmission to use
engine braking to slow down.
Turning on the system
CRUISE
To operate the cruise control, push the main switch. This turns
the system on. The indicator light in the instrument cluster
shows that you can now set your desired cruising speed.
Another push on the switch will turn the system completely off.
When the ignition key is turned off, the main switch is also
automatically turned off. To use the cruise control again, push
the main switch again to turn it on.
CAUTION
To avoid accidental cruise control engagement, keep
the main switch off when not using the cruise control.

STARTING AND DRIVING
141
TRACTION CONTROL SYSTEM
The traction control system automatically controls
spinning of the rear wheels which may occur when
accelerating on slippery road surfaces, thus assisting
driver control and driving power to the rear wheels.
When you turn the ignition switch on, this system always
turns on. Leave the system on during ordinary driving so
that it can operate when needed. When traction control is
applied, the slip indicator light blinks.
You can turn off the traction control system by pushing
the “TRAC−OFF−” switch. The “TRAC OFF”
indicator / warning light will then come on. Pushing the
“TRAC−OFF−” switch a second time turns the system
back on and extinguishes the “TRAC OFF”
indicator / warning light.
You may hear a slight clicking noise in the engine compartment
when the engine is started. This means that the traction control
system is in the self−check mode, and does not indicate
malfunction. When the traction control system is operating,
you may feel vibration of your vehicle, caused by operation of
the brakes. This indicates the system is functioning properly.
When getting the vehicle out of mud or new snow, etc. the
traction control system will operate to prevent the wheels from
spinning. Even though the accelerator pedal is fully depressed,
the engine speed will be restrained to a certain level.

STARTING AND DRIVING
142
Traction control failure warning
If the “TRAC OFF” indicator / warning light flashes, contact
your Lexus dealer as soon as possible. There may be trouble
in the traction control system.
CAUTION
Under certain slippery road conditions, full stability of
the vehicle and power to the rear wheels cannot be
maintained, even though the traction control system is
in operation. In situations where the road surface is
covered with ice or snow, your vehicle should be fitted
with snow tires or tire chains and driven at a more
cautious pace.
BRAKE SYSTEM
The tandem master cylinder brake system is a hydraulic
system with two separate sub−systems. If either sub−system
should fail, the other will still work. However, the pedal will be
harder to press, and your stopping distance will be longer.
Also, the brake system warning light may come on.
CAUTION
Do not drive your vehicle with only a single brake
system. Have your brakes fixed immediately.
Brake booster
The brake booster uses engine vacuum to power−assist the
brakes. If the engine should quit while you are driving, you can
bring the vehicle to a stop with normal pedal pressure. There
is enough reserve vacuum for one or two stops but no more!
CAUTION

Do not pump the brake pedal if the engine stalls. Each
push on the pedal uses up your vacuum reserve.

Even if the power assist is completely lost, the brakes
will still work. But you will have to push the pedal
hard − much harder than normal. And your braking
distance will be longer.

STARTING AND DRIVING
143
Anti−lock brake system
The anti−lock brake system is designed to prevent
lock−up of the wheels during sudden braking or braking
on slippery road surfaces. This assists the driver in
controlling the vehicle under these circumstances.
The anti−lock brake system becomes operative after the
vehicle has accelerated to a speed in excess of approximately
10 km / h (6 mph). It stops operating when the vehicle
decelerates to a speed below approximately 5 km / h (3 mph).
You may hear a sound in the engine compartment for a few
seconds when the engine is started or just after the vehicle is
started. This means that the anti−lock brake system is in the
self check mode, and does not indicate a malfunction.
When the anti−lock brake system function is in action, you may
feel the brake pedal pulsating and hear a noise. In this
situation, to let the anti−lock brake system work for you, just
hold the brake pedal down more firmly. Do not pump the brake.
The brake pedal pulsation caused by the anti−lock brake
system may indicate hazardous road surface conditions.
Although the anti−lock brake system assists in providing
vehicles control, it is still important to drive with all due care,
because the anti−lock brake system cannot overcome the
laws of physics that act on your vehicle:

Braking capability is dependent on tire friction with the road
surface.
Even though the anti−lock brake system is operating, a
driver cannot maintain full control on certain slippery road
surfaces, when cornering at high speeds, or in violent
maneuvers.

Avoid high speeds on wet roads. The anti−lock brake
system cannot eliminate the risk of hydroplaning and loss
of tire friction.
Always maintain a safe distance from the vehicle in front of
you. Compared with vehicles riot fitted with an anti−lock brake
system, your vehicle may require a longer stopping distance
in the following cases:

Driving on rough, gravel or snow−covered roads.

Driving with tire chains installed.

Driving on roads where the road surface is pitted or has
other differences in surface height.