check engine lexus LS400 1996 Engine / 1996 LS400: STARTING AND DRIVING

STARTING AND DRIVING
126
THREE±WAY CATALYTIC
CONVERTER
Three±way catalytic converters are emission control
devices installed in the exhaust system.
The three±way catalytic converter located at the confluence
of exhaust pipes looks somewhat like a muffler, but its
purpose is to reduce pollutants in the exhaust gas.
CAUTION!

Keep people and combustible materials away from
the exhaust pipe while the engine is running. The
exhaust gas is very hot.
Do not drive, idle or park your vehicle over anything
that might burn easily such as grass, leaves, paper
or rags.
NOTICE
A large amount of unburned gases flowing into the
three±way catalytic converter may cause it to
overheat and create a fire hazard. To prevent this and
other damage, observe the following precautions:
Use only unleaded gasoline.
Do not drive with an extremely low fuel level;
running out of fuel could cause the engine to
misfire, creating an excessive load on the
three±way catalytic converter.
Do not allow the engine to run at idle speed for more
than 20 minutes.
Avoid racing the engine.
Do not push±start or pull±start your vehicle.
Do not turn off the ignition while the vehicle is
moving.
Keep your engine in good running order.
Malfunctions in the engine electrical system,
electronic ignition system/distributor ignition
system or fuel system could cause an extremely
high three±way catalytic converter temperature.
If the engine becomes difficult to start or stalls
frequently, take your vehicle in for a check±up as
soon as possible. Remember, your Lexus dealer
knows your vehicle and its three±way catalytic
converter system best.

STARTING AND DRIVING
127
To ensure that the three±way catalytic converter
and the entire emission control system operate
properly, your vehicle must receive the periodic
inspections required by the Lexus Maintenance
Schedule. For scheduled maintenance
information, refer to the separate ªOwner's Manual
Supplement/Maintenance Schedule.º
ENGINE EXHAUST CAUTION
CAUTION!

Avoid inhaling the engine exhaust. It contains
carbon monoxide, which is a colorless and
odorless gas. It can cause unconsciousness or
even death.
Make sure the exhaust system has no holes or
loose connections. The system should be checked
from time to time. If you hit something, or notice a
change in the sound of the exhaust, have the
system checked immediately.
Do not run the engine in a garage or enclosed area
except for the time needed to drive the vehicle in or
out. The exhaust gases cannot escape, making this
a particularly dangerous situation.
Do not remain for a long time in a parked vehicle
with the engine running. If it is unavoidable,
however, do so only in an unconfined area and
adjust the heating or cooling system to force
outside air into the vehicle.
Keep the trunk lid closed while driving. An open or
unsealed trunk lid may cause exhaust gases to be
drawn into the vehicle. If you must drive with the
trunk lid open to accommodate a large object, close
the windows, open all the dashboard vents and
have the heating or cooling system deliver fresh air
into the vehicle by turning the fan to high speed
with the air intake control button in the OUTSIDE
AIR mode.
To allow proper operation of your vehicle's
ventilation system, keep the inlet grilles in front of
the windshield clear of snow, leaves, or other
obstructions.
If you smell exhaust fumes in the vehicle, drive with
the windows open and the trunk lid closed. Have
the cause immediately located and corrected.

STARTING AND DRIVING
128
BEFORE STARTING THE ENGINE
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle, head restraint
height and steering wheel angle.
3. Adjust inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts.
Remember to check that the service reminder indicators
function when turning the key to ªONº, and check the fuel
gauge to see that you have sufficient fuel.
IGNITION SWITCH WITH STEERING
LOCK
ªSTARTº ± Starter motor on. The key will return to the
ªONº position when released.
For starting tips, see page 130.
ªONº ± Engine on and all accessories on.
This is the normal driving position.
NOTICE
Do not leave the key in the ªONº position if the
engine is not running. The battery will discharge
and the electronic ignition system/distributor
ignition system could be damaged.
ªACCº ± Accessories such as the radio operate, but the
engine is off.

STARTING AND DRIVING
130
HOW TO START THE ENGINE
Before cranking
1. Apply the parking brake firmly.
2. Turn off unnecessary lights and accessories.
3. Put the selector lever in ªPº. If you need to restart the
engine while the vehicle is moving, put the selector lever in
ªNº. A starter safety device will prevent the starter from
operating if the selector lever is in any drive position.
4. Depress the brake pedal and hold it to the floor until you
are ready to drive off.
Starting the engine
Before starting the engine, be sure to follow the instructions
in ªBefore crankingº.
Normal starting procedure
The multiport fuel injection system/sequential multiport fuel
injection system in your engine automatically controls the
proper air±fuel mixture for starting. You can start a cold or hot
engine as follows:
1. With your foot off the accelerator pedal, crank the engine
by turning the key to ªSTARTº. Release it when the engine
starts.
2. After the engine runs for about 10 seconds, you are
ready to drive.If the weather is below freezing, let the engine warm up for
a few minutes before driving. Do not leave the vehicle while
the engine is warming up.
If the engine stalls...
Simply restart it, using the correct procedure given in normal
starting.
If the engine will not start
See ªIf your vehicle will not startº on page 160.
NOTICE
Do not crank for more than 15 seconds at a time.
This may overheat the starter and wiring systems.
Do not race a cold engine.
If the engine becomes difficult to start or stalls
frequently, have the engine checked immediately.

STARTING AND DRIVING
138If the vehicle speed falls below about 40 km/h (25 mph), the
preset speed will be automatically cancelled.
If the vehicle speed drops 16 km/h (10 mph) below the preset
speed, the preset speed will also automatically be cancelled.
If the preset speed automatically cancels out for other than
these reasons, have your vehicle checked by your Lexus
dealer at the earliest opportunity.
Resetting to a faster speed
Press the control lever upward in the ªRES/ACCº direction
and hold it. Release the lever when the desired speed is
attained. While the lever is held upward, the vehicle will
gradually gain speed.
When the difference between the actual vehicle speed and
the set speed is less than 5 km/h (3 mph), the set speed can
be increased 1.6 km/h (1 mph) each time by pressing the
control lever upward in the ªRES/ACCº direction quickly
within 0.6 seconds.
However, a quicker way to reset is to accelerate the vehicle
and then press the control lever downward in the
ªSET/COASTº direction.
Resetting to a slower speed
Press the control lever downward in the ªSET/COASTº
direction and hold it. Release the lever when the desired
speed is attained. While the lever is held downward, the
vehicle speed will gradually decrease.
When the difference between the actual vehicle speed and
the set speed is less than 5 km/h (3 mph), the set speed can
be lowered 1.6 km/h (1 mph) each time by pressing the
control lever downward in the ªSET/COASTº direction
quickly within 0.6 seconds.
However, a quicker way to reset is to depress the brake
pedal and then press the control lever downward in the
ªSET/COASTº direction.
Even if you downshift the transmission from the ªDº position
to ª3º with the cruise control on, engine braking will not be
applied because the cruise control is not cancelled. To
decrease the vehicle speed, reset to a slower speed with the
cruise control lever or depress the brake pedal. If you use the
brake pedal, cruise control is cancelled.
Resuming the preset speed
If the preset speed is cancelled by pulling the control lever
or by depressing the brake pedal, pushing the lever up in the
ªRES/ACCº direction will restore the speed set prior to
cancellation. However, once the vehicle speed falls below
about 40 km/h (25 mph), the preset speed will not be
resumed.

STARTING AND DRIVING
141
TRACTION CONTROL SYSTEM
The traction control system automatically helps control
the spinning of the rear wheels which may occur when
accelerating on slippery road surfaces, thus assisting
driver control and driving power of the rear wheels.
When you turn the ignition switch on, this system
always turns on. Leave the system on during ordinary
driving so that it can operate when needed. When
traction control is applied, the slip indicator light
blinks.
You can turn off the traction control system by pushing
the ªTRAC±OFF±º switch. The ªTRAC OFFº
indicator/warning light will then come on. Pushing the
ªTRAC±OFF±º switch a second time turns the system
back on and extinguishes the ªTRAC OFFº
indicator/warning light.
You may hear a slight clicking noise in the engine
compartment when the engine is started. This means that
the traction control system is in the self±check mode, and
does not indicate malfunction. When the traction control
system is operating, you may feel vibration of your vehicle,
caused by operation of the brakes. This indicates the system
is functioning properly.
When getting the vehicle out of mud or new snow, etc. the
traction control system will operate to prevent the wheels
from spinning. Even though the accelerator pedal is fully
depressed, the engine speed will be restrained to a certain
level.

STARTING AND DRIVING
143
Anti±lock brake system
The anti±lock brake system is designed to prevent
lock±up of the wheels during sudden braking or
braking on slippery road surfaces. This assists the
driver in controlling the vehicle under these
circumstances.
The anti±lock brake system becomes operative after the
vehicle has accelerated to a speed in excess of
approximately 10 km/h (6 mph). It stops operating when the
vehicle decelerates to a speed below approximately 5 km/h
(3 mph).
You may hear a sound in the engine compartment for a few
seconds when the engine is started or just after the vehicle
is started. This means that the anti±lock brake system is in
the self check mode, and does not indicate a malfunction.
When the anti±lock brake system function is in action, you
may feel the brake pedal pulsating and hear a noise. In this
situation, to let the anti±lock brake system work for you, just
hold the brake pedal down more firmly. Do not pump the
brake.
The brake pedal pulsation caused by the anti±lock brake
system may indicate hazardous road surface conditions.
Although the anti±lock brake system assists in providing
vehicle control, it is still important to drive with all due care,
because the anti±lock brake system cannot overcome the
laws of physics that act on your vehicle:
Braking capability is dependent on tire friction with the road
surface.
Even though the anti±lock brake system is operating, a
driver cannot maintain full control on certain slippery road
surfaces, when cornering at high speeds, or in violent
maneuvers.
Avoid high speeds on wet roads. The anti±lock brake
system cannot eliminate the risk of hydroplaning and loss
of tire friction.
Always maintain a safe distance from the vehicle in front of
you. Compared with vehicles not fitted with an anti±lock
brake system, your vehicle may require a longer stopping
distance in the following cases:
Driving on rough, gravel or snow±covered roads.
Driving with tire chains installed.
Driving on roads where the road surface is pitted or has
other differences in surface height.