lexus LS400 1998 Audio System / LEXUS 1998 LS400 OWNER'S MANUAL (OM50498U)

COMFORT ADJUSTMENT
106
16L146
Move seat fully back
A forwardfacing child restraint system should be put on
the front seat only when it is unavoidable. Always move the
seat as far back as possible, because the force of a deploying
airbag could cause death or serious injury to the child. Do
not allow the child to lean over the front door or around the
front door even if the child is seated in a child restraint
system. It is dangerous if the side airbag inflates, and the
impact could cause death or serious injury to the child.
16L1651
1. Run the lap and shoulder belt through or around the convertible
seat following the instructions provided by its manufacturer and
inserting the tab into the buckle taking care not to twist the belt. Keep
the lap portion of the belt tight.
CAUTION
After inserting the tab, make sure the tab and buckle are
locked and that the lap and shoulder portions of the belt are
not twisted.
Do not insert coins, clips, etc. in the buckle as this may
prevent you from properly latching the tab and buckle.
If the seat belt does not function normally, immediately
contact your Lexus dealer. Do not use the seat until the seat
belt is fixed. It cannot protect your child from injury.

COMFORT ADJUSTMENT
107
16L1661
2. Fully extend the shoulder belt to put it in the lock mode. When
the belt is then retracted slightly, it cannot be extended.
To hold the convertible seat securely, make sure the belt is in the lock
mode before letting the belt to retract.
16L1671
3. While pressing the convertible seat firmly against the seat
cushion and seatback, let the shoulder belt retract as far as it will go
to hold the convertible seat securely.

COMFORT ADJUSTMENT
108
16L1681
CAUTION
Push and pull the child restraint system in different directions
to be sure it is secure. Follow all the installation instructions
provided by its manufacturer.
16L1691
4. To remove the convertible seat, press the bucklerelease button
and allow the belt to retract completely. The belt will move freely
again and be ready to work for an adult or older child passenger.

COMFORT ADJUSTMENT
109 (C) Booster seat installation
16L1594
A booster seat is used in forwardfacing position only.
16L152
Move seat fully back
CAUTION
A forwardfacing child restraint system should be put on the
front seat only when it is unavoidable. Always move the seat
as far back as possible, because the force of a deploying airbag
could cause death or serious injury to the child. Do not allow
the child to lean over the front door or around the front door
even if the child is seated in a child restraint system. It is
dangerous if the side airbag inflates, and the impact could
cause death or serious injury to the child.

COMFORT ADJUSTMENT
110
16L1702
1. Sit the child on a booster seat. Run the lap and shoulder belt
through or around the booster seat and child following the
instructions provided by its manufacturer and insert the tab into the
buckle.
Make sure the shoulder belt is correctly across the child’s shoulder
and that the lap belt is positioned as low as possible on child’s hips.
See ”Seat belts” on page 80 for details.
CAUTION
Always make sure the shoulder belt is positioned across the
center of child’s shoulder. The belt should be kept away
from child’s neck, but not falling off child’s shoulder.
Failure to do so could reduce the amount of protection in an
accident and cause serious injuries in a collision.
Highpositioned lap belts and loosefitting belts both could
cause serious injuries due to sliding under the lap belt
during a collision or other unintended result. Keep the lap
belt positioned as low on hip as possible.
For child’s safety, do not place the shoulder belt under
child’s arm.
After inserting the tab, make sure the tab and buckle are
locked and that the lap and shoulder portions of the belt are
not twisted.
Do not insert coins, clips, etc. in the buckle as this may
prevent you from properly latching the tab and buckle.
If the seat belt does not function normally, immediately
contact your Lexus dealer. Do not use the seat until the seat
belt is fixed. It cannot protect your child from injury.

COMFORT ADJUSTMENT
111
16L1711
2. To remove the child restraint system, press the bucklerelease
button and allow the belt to retract.Top strap anchors and locations
16L156
If your child restraint system requires the use of a top strap, latch
the hook onto the anchor bracket and tighten the top strap.
See the following instructions to install the anchor bracket.

COMFORT ADJUSTMENT
112
16L0381
1
Center 2
362 mm (14.3 in.) 3
55 mm (2.2 in.)
4
52 mm (2.0 in.) 5
5 mm (0.2 in.)
1. Run your fingers across the trim of the filler panel to locate the
holes underneath it in the positions shown above.
2. Make a hole in the covering directly above the hole in the filler
panel.
16L039
3. Remove the seals from the anchors using a screwdriver or the
like.

COMFORT ADJUSTMENT
113
16L0401
1
Bolt 2
Anchor bracket 3
Spacer
4. Insert a 15 mm (0.6 in.) spacer, and tighten down the anchor
bracket for your child restraint system with a bolt. Torque the bolt
to 16.5 24.7 N·m (1.68 2.52 kgf·m, 12.2 18.2 ft·lbf.).
To comply with Canada Motor Vehicle Safety Standards, vehicles
sold in Canada are provided with a bracket set in the glovebox.
DRIVING POSITION MEMORY
SYSTEM
The micro computer can memorize the position of the driver’s seat,
the height of the shoulder belt anchor of the driver’s seat belt, and the
positions of the tilt and telescopic steering, and outside rear view
mirrors. Two different driving position profiles can be entered into
the computer’s memory.
Recording a driving position in the computer’s memory can only be
done when the ignition key is in the ”ON” position and the shift lever
is in the ”P” position.
Setting a driving position
16L055
1. Adjust the driver’s seat, driver’s shoulder belt anchor, tilt and
telescopic steering and outside rear view mirrors to the desired
position.
2. While pushing the ”SET” button, push button ”1” or ”2” until
the signal beeps.

COMFORT ADJUSTMENT
114The beep sound means that the positions are recorded in the
computer ’s memory.
By repeating these two steps and pressing the remaining button, the
driving position for another driver can be recorded.
To set a new memorized position, select the desired position and
perform step 2. The previous memory will be erased and the new
position will be set.
To make only slight changes to an already memorized position, the
easiest way is to first activate the memorized position, then make the
desired changes and perform step 2 above.
Activating a memorized position
16L056
When you push button ”1” or ”2”, the driving position will be
automatically adjusted to the position recorded for that button.Conditions for memorized position activation
Ignition key ”ON” and shift lever in ”P” position.
All parts of the memorized positions can be activated.
However, if the brake pedal is being depressed, the seat position
will not change.
Key not in ignition switch and within 30 seconds of opening
driver’s door.
The memorized position can be activated, except for the tilt and
telescopic steering.
If any driving position memory switch is pushed while one of the
memorized driving position profiles is being activated, the operation
will stop.
To activate the system, push the desired button (”1” or ”2”) again.
The driving position memory control system cannot be operated
while the vehicle is moving.
If the vehicle’s battery is disconnected, the computer’s memory will
be erased and the memorized positions will have to be set again.
CAUTION
Do not start the vehicle while the adjustments are being
made.
Take care not to select the wrong button, or the seat could
strike the rear passenger or hit your body against the
steering wheel. If this happens, you can stop the movement
by pressing another driving position memory switch, or
depressing the brake pedal.

COMFORT ADJUSTMENT
115