transmission lexus LS400 1998 Audio System / LEXUS 1998 LS400 (OM50498U) User Guide

STARTING AND DRIVING
163 5. Release the parking brake and brake pedal. Depress the
accelerator pedal slowly for smooth starting.
In normal cruising, the vehicle will start in the first gear and
automatically shift up to the most suitable gear. On inclines, declines
or winding roads, etc., the vehicle shifts up and down automatically
according to the running conditions to obtain the suitable driving
power and engine braking.
In ”4” position, the automatic transmission system will select the
most suitable gear for the running conditions such as hill climbing,
hard towing, etc.
If you need to accelerate rapidly while driving, depress the
accelerator pedal to the full throttle position. This provides more
acceleration by automatically downshifting the transmission to the
next lower gear or beyond, depending on the vehicle speed.
If engine braking is needed, such as in descending a long hill, see ”(b)
Using engine braking”.
(b) Using engine braking
31L010-3
To use the braking power of the engine, downshift the transmission
in the way described below:
1
Shift into the ”4” position. The transmission will downshift to
the fourth gear and engine braking will be obtained.
When the cruise control is being used, even if you downshift
from ”D” to ”4”, engine braking will not be applied because the
cruise control is not cancelled. If you need to decrease the
vehicle speed, see page 170.
2
Shift into the ”3” position. The transmission will downshift to
the third gear when the vehicle speed is or becomes lower than
154 km/h (96 mph) and more powerful engine braking will be
obtained.

STARTING AND DRIVING
164
3
Shift into the ”2” position. The transmission will downshift to
the second gear when the vehicle speed is or becomes lower
than 104 km/h (65 mph) and more powerful engine braking
than that of ”3” position will be obtained.
4
Shift into the ”L” position. The transmission will downshift to
the first gear when the vehicle speed is or becomes lower than
18 km/h (11 mph) and maximum engine braking will be
applied.
CAUTION
Be careful when downshifting on a slippery surface. The
abrupt change in engine speed could cause the vehicle to spin
or skid.
(c) Using the ”3”, ”2” and ”L” positions
The ”3”, ”2” and ”L” positions are used for strong engine braking as
described previously.
With the selector lever in ”3”, ”2” or ”L”, you can start the vehicle
in motion as with the lever in ”D”.
With the selector lever in ”3” or ”2”, the vehicle will start in the first
gear and automatically shift to the third or second gear.
With the selector lever in ”L”, the transmission is engaged in the first
gear.
NOTICE
Be careful not to overrev the engine. Watch the tachometer
to keep engine rpm from going into the red zone. The
approximate maximum allowable speed for each position is
given below for your reference:
”3” 160 km/h (99 mph). . . .
”2” 104 km/h (65 mph). . . .
”L” 68 km/h (42 mph). . . .
Do not continue hill climbing or hard towing for a long time
in the ”3”, ”2” or ”L” position. This may cause severe
automatic transmission damage from overheating. To
prevent such damage, ”4” position should be used in hill
climbing or hard towing.

STARTING AND DRIVING
166
(f) Good driving practice
If the transmission repeatedly upshifts and downshifts between
the fourth and overdrive gears when climbing a gentle slope, shift
the selector lever to the ”4” position. Be sure to shift the selector
lever to the ”D” position after climbing the slope.
When towing a trailer, in order to maintain efficient engine
braking and electrical charging performance, do not use
overdrive. The selector lever must be in the ”4” position.
CAUTION
Always keep your foot on the brake pedal while stopped with
the engine running. This prevents the vehicle from creeping.
NOTICE
Do not hold the vehicle on an upgrade with the accelerator
pedal. This can cause the transmission to overheat. Always use
the brake pedal or parking brake.
(g) Rocking your vehicle if stuck
CAUTION
If your vehicle becomes stuck in snow, mud, sand, etc., then
you may attempt to rock the vehicle free by moving it forward
and backward. Do not attempt this procedure if people or
objects are anywhere near the vehicle. During the rocking
operation the vehicle may suddenly move forward or back as
it becomes unstuck, causing injury or damage to nearby
people or objects.
NOTICE
If you rock your vehicle, observe the following precautions to
prevent damage to the transmission and other parts.
Do not depress the accelerator pedal while shifting the
selector lever or before the transmission is completely shifted
to forward or reverse gear.
Do not race the engine and avoid spinning the wheels.
If your vehicle remains stuck after rocking the vehicle several
times, consider other ways such as towing.

STARTING AND DRIVING
167
(h) If you cannot shift the selector lever
If you cannot shift the selector lever even though the brake pedal is
depressed, use the shift lock override button. For instructions, see
”If you cannot shift automatic transmission selector lever” on page
209.
(i) If the ”ECT PWR” indicator light flashes
If the ”ECT PWR” indicator light flashes, contact your Lexus dealer
as soon as possible. There may be trouble in the transmission
system.
ELECTRONIC THROTTLE
CONTROL SYSTEM
The electronic throttle control system always maintains
appropriate engine output in relation to the accelerator opening
in all driving conditions.
31L0082
1
Power mode 2
Normal mode 3
Snow mode
The electronic throttle control system has 3 modes: Normal,
Power and Snow modes.
Normal mode: For ordinary driving, Lexus recommends that you
use the normal mode to improve fuel economy.
Power mode: For more powerful acceleration and sporty driving.

STARTING AND DRIVING
168In the power mode, the ”ECT PWR” light in the instrument cluster
is on and the transmission is shifted up at higher vehicle speeds and
shifted down more responsively than is the normal mode.
To return to the normal mode, push the driving pattern selector
switch lightly on the ”SNOW” side.
Snow mode: For slippery road surfaces such as in snow. In this
mode, the spinning of the rear wheels is controlled appropriately.
When you push the driving pattern selector switch on the ”SNOW”
side, the snow mode is turned on and the ”ECT SNOW” light in the
instrument cluster comes on.
To return to the normal mode, push the driving pattern selector
switch on the ”SNOW” side again.
When you turn the ignition switch off in the snow mode, the mode
automatically changes to the normal mode.
CRUISE CONTROL
The cruise control allows you to cruise the vehicle at a desired
speed over 40 km/h (25 mph) with your foot off the accelerator
pedal.
Your cruising speed can be maintained although a slight speed
change may occur when driving up or down a gradient, within the
limits of engine performance. On steeper hills, a great speed change
will occur so it is better to drive without the cruise control.
When the cruise control is on, the driving pattern of the automatic
transmission is fixed in the normal position, regardless of the
position of the selector switch.
CAUTION
To help maintain maximum control of your vehicle, do not
use the cruise control when driving in heavy or varying
traffic, or on slippery (rainy, icy or snowcovered) or
winding roads.
Avoid vehicle speed increases when driving downhill. If the
vehicle speed is too fast in relation to the cruise control set
speed, cancel the cruise control then downshift the
transmission to use engine braking to slow down.

STARTING AND DRIVING
169
Turning on the system
31L067
To operate the cruise control, push the main switch. This turns the
system on. The indicator light in the instrument cluster shows that
you can now set your desired cruising speed. Another push on the
switch will turn the system completely off.
When the ignition key is turned off, the main switch is also
automatically turned off. To use the cruise control again, push the
main switch again to turn it on.
CAUTION
To avoid accidental cruise control engagement, keep the main
switch off when not using the cruise control.
Setting at a desired speed
31L068
The transmission must be in ”D” or ”4” before you set the cruise
control speed.
Bring the vehicle to the desired speed, press the control lever
downward in the ”SET/COAST” direction and release it. This sets
the vehicle at that speed. Now you may take your foot off the
accelerator pedal. If you need acceleration for example, when
passing depress the accelerator pedal enough for the vehicle to
exceed the set speed. When you release the accelerator pedal, the
vehicle will return to the speed set prior to the acceleration.
Cancelling the preset speed
You can cancel the preset speed by either of the following:
a. Pulling the control lever in the ”CANCEL” direction.
b. Depressing the brake pedal.

STARTING AND DRIVING
170If the vehicle speed falls below about 40 km/h (25 mph), the preset
speed will be automatically cancelled.
If the vehicle speed drops 16 km/h (10 mph) below the preset speed,
the preset speed will also automatically be cancelled.
If the preset speed automatically cancels out for other than these
reasons, have your vehicle checked by your Lexus dealer at the
earliest opportunity.
Resetting to a faster speed
Press the control lever upward in the ”RES/ACC” direction and hold
it. Release the lever when the desired speed is attained. While the
lever is held upward, the vehicle will gradually gain speed.
When the difference between the actual vehicle speed and the set
speed is less than 5 km/h (3 mph), the set speed can be increased 1.6
km/h (1 mph) each time by pressing the control lever upward in the
”RES/ACC” direction quickly within 0.6 seconds.
However, a quicker way to reset is to accelerate the vehicle and then
press the control lever downward in the ”SET/COAST” direction.
Resetting to a slower speed
Press the control lever downward in the ”SET/COAST” direction
and hold it. Release the lever when the desired speed is attained.
While the lever is held downward, the vehicle speed will gradually
decrease.
When the difference between the actual vehicle speed and the set
speed is less than 5 km/h (3 mph), the set speed can be lowered 1.6
km/h (1 mph) each time by pressing the control lever downward in
the ”SET/COAST” direction quickly within 0.6 seconds.
However, a quicker way to reset is to depress the brake pedal and
then press the control lever downward in the ”SET/COAST”
direction.
Even if you downshift the transmission from the ”D” position to ”4”
with the cruise control on, engine braking will not be applied because
the cruise control is not cancelled. To decrease the vehicle speed,
reset to a slower speed with the cruise control lever or depress the
brake pedal. If you use the brake pedal, cruise control is cancelled.
Resuming the preset speed
If the preset speed is cancelled by pulling the control lever or by
depressing the brake pedal, pushing the lever up in the ”RES/ACC”
direction will restore the speed set prior to cancellation. However,
once the vehicle speed falls below about 40 km/h (25 mph), the
preset speed will not be resumed.

STARTING AND DRIVING
175
Vehicle skid control failure warning
31L073
In the following cases, the warning message appears and the
reminder light next to the warning message and the ”VSC OFF”
indicator light come on. And the warning tone also sounds.
(a) After the removal of the battery terminals (See ”Initial
adjustment of vehicle skid control system” described below.)
(b) If the vehicle skid control system malfunctions
If the message appears for the cause of (b), have your vehicle
checked by Lexus dealer as soon as possible.
Although the message appears, there is no problem to continue your
normal driving.
Initial adjustment of vehicle skid control system
After the battery terminals are disconnected, an initial adjustment
should be made. At this time, the reminder light comes on and the
warning message appears in the multi information display.
Make an initial adjustment in the following ways:
1. Apply the parking brake and put the transmission in ”P”.
2. Connect the battery terminals.
3. Turn the ignition switch on. At this time, the ”VSC OFF”
indicator light comes on and then about 6 seconds later, the reminder
light comes on and the ”CHECK VSC” warning message appears in
the multi information display.
4. The warning message and the ”VSC OFF” indicator light go out
about 15 seconds after the ignition switch is turned on. If the vehicle
is shaken after the ignition switch is turned to ”ON”, it may take
longer to go out the warning message.
If the warning message does not go out about 1 minute after you turn
the ignition switch on, turn it off and then on again.
If the vehicle is on the moving object like a ship or turntable, an
accurate adjustment cannot be made. Move the vehicle on the
ground (or the part not causing vibrations to the vehicle) and make
an adjustment from step 1.

DRIVING TIPS
181
BREAKIN PERIOD
Drive gently and avoid high speeds.
You need not follow a breakin schedule with your new Lexus. But
following a few simple tips for the first 1600 km (1000 miles) can
add to the future economy and long life of your vehicle:
Do not drive over 88 km/h (55 mph).
Avoid overrevving. Maintain engine speed between 2000 and
4000 rpm.
Avoid fullthrottle starts.
Try to avoid hard stops during the first 300 km (200 miles).
Do not drive for a long time at any single speed, either fast or slow.
Do not tow a trailer during the first 800 km (500 miles).
OPERATION IN FOREIGN
COUNTRIES
If you plan to drive your Lexus in another country ...
First, comply with the vehicle registration laws.
Second, confirm the availability of the correct fuel (unleaded and
minimum octane rating).
TIPS FOR DRIVING IN VARIOUS
CONDITIONS
Always slow down in gusty crosswinds. This will allow you
much better control.
Drive slowly onto curbs and, if possible, at a right angle. Avoid
driving onto high, sharpedged objects and other road hazards.
Failure to do so can lead to severe tire damage resulting in tire
bursts.
When parking on a hill, turn the front wheels until they touch the
curb so that the vehicle will not roll. Apply the parking brake, and
place the transmission in ”P”. If necessary, block the wheels.
Washing your vehicle or driving through deep water may get the
brakes wet. To see whether they are wet, check that there is no
traffic near you and then press the pedal lightly. If you do not feel
a normal braking force, the brakes are probably wet. To dry them,
drive the vehicle cautiously while lightly pressing the brake pedal
with the parking brake applied. If they still do not work safely,
pull to the side of the road and call a Lexus dealer for assistance.
CAUTION
Before driving off, make sure the parking brake is fully
released and that the parking brake reminder light is off.

DRIVING TIPS
183 Use a washer fluid containing an antifreeze solution.
This product is available at your Lexus dealer and most auto parts
stores. Follow the manufacturer’s directions for how much to mix
with water.
NOTICE
Do not use engine antifreeze or any other substitute because it
may damage your vehicle’s paint.
Do not use your parking brake when there is a possibility it could
freeze.
When parking, put the transmission into ”P” and block the front
wheels. Do not use the parking brake, or snow or water accumulated
in and around the parking brake mechanism may freeze the parking
brake, making it hard to release.
Keep ice and snow from accumulating under the fenders.
Ice and snow built up under your fenders can make steering difficult.
During bad winter driving, stop and check under the fenders
occasionally.
Depending on where you are driving, we recommend you carry
some emergency equipment.
Some of the things you might put in the vehicle are tire chains,
window scraper, bag of sand or salt, flares, small shovel, jumper
cables, etc.
TRAILER TOWING
Your vehicle is designed primarily as a passengercarrying vehicle.
Towing a trailer will have an adverse effect on handling,
performance, braking, durability and driving economy (fuel
consumption, etc.). Your safety and satisfaction depend on the
proper use of correct equipment and cautious driving habits. For
your safety and the safety of others, you must not overload your
vehicle or trailer. Lexus warranties do not apply to damage or
malfunction caused by towing a trailer for commercial purposes.
Ask your local Lexus dealer for further details before towing.
NOTICE
When towing a trailer, be sure to consult your Lexus dealer for
further information on additional requirements.
Weight limits
Before towing, make sure the total trailer weight, gross vehicle
weight, gross axle weight and trailer tongue load are all within
the limits.
The total trailer weight and tongue load can be measured with
platform scales found at a highway weighing station, building
supply company, trucking company, junk yard, etc.