gas type lexus LS400 1998 Audio System / LEXUS 1998 LS400 OWNER'S MANUAL (OM50498U)

62L0051
Temperature range anticipated before next oil change
ENGINE
225
SPECIFICATIONS
GENERAL
Model
Type
Bore and stroke
Displacement
Valve clearance (engine cold)
Intake
Exhaust
Drive belt tension
1UZFE
8 cylinder V type, 4 cycle, gasoline
87.5 X 82.5 mm (3.44 X 3.25 in.)
3969 cm
3 (242.1 cu.in.)
0.15 0.25 mm (0.006 0.010 in.)
0.25 0.35 mm (0.010 0.014 in.)
Automatic adjustment
LUBRICATION SYSTEM
Oil capacity
Drain and refill
with filter
without filter
Oil grade

Recommended oil viscosity (SAE):
5.6 L (5.9 qt., 4.9 lmp.qt.)
5.3 L (5.6 qt., 4.7 lmp.qt.)
API SH, ”EnergyConserving II” or SJ, ”EnergyConserving”
multigrade engine oil or ILSAC multigrade engine oil

ENGINE
227
FUEL
Fuel type
Your vehicle must use only unleaded gasoline.
To help prevent gas station mixups, your Lexus has a smaller fuel
tank opening. The special nozzle on pumps with unleaded fuel will
fit it, but the larger nozzle on pumps with leaded gas will not.
At a minimum, the gasoline you use should meet the specifications
of ASTM D4814 in the U.S.A. and CGSB 3.5M93 in Canada.
NOTICE
Do not use leaded gasoline. Use of leaded gasoline will cause the
threeway catalytic converter to lose its effectiveness and the
emission control system to function improperly. Also, this can
increase maintenance costs.
Octane rating
Select premium unleaded gasoline with an Octane Rating of 91
(Research Octane Number 96) or higher for optimum engine
performance. However, if such premium type cannot be
obtained, you may temporarily use unleaded gasoline with an
Octane Rating as low as 87 (Research Octane Number 91).
Use of unleaded fuel with an octane number or rating lower than
stated above will cause persistent heavy knocking. If severe, this
will lead to engine damage.
If your engine knocks ...
If you detect heavy knocking even when using the recommended
fuel, or if you hear steady knocking while holding a steady speed on
level roads, consult your Lexus dealer.
However, now and then, you may notice light knocking for a short
time while accelerating or driving up hills. This is no cause for
concern.
Gasolines containing detergent additives
Lexus recommends use of gasolines that contain detergent
additives to avoid buildup of engine deposits.
For further details, ask your Lexus dealer or a local gasoline retailer.

ELECTRICAL COMPONENTS
257
Adding distilled water
(Maintenance type battery only)
64L062
1
Low 2
O.K.
1. Remove the vent plugs.
2. Add distilled water to cells needing fluid.
If the side of your battery is covered, check the water level by looking
down directly above the cell as illustrated above.
3. Retighten the vent plugs securely.
NOTICE
Do not overfill the cells. Excess electrolyte could squirt out
of the battery during heavy charging, causing corrosion or
damage.
Use a cover on the battery for longer life.
BATTERY RECHARGING
PRECAUTIONS
During recharging, the battery is producing hydrogen gas.
Therefore, before recharging:
1. Maintenance type batteries Remove the vent plugs.
2. If recharging with the battery installed on the vehicle, be sure to
disconnect the ground cable.
3. Make sure the power switch on the recharger is off when
connecting the charger cables to the battery and when disconnecting
them.
CAUTION
Always charge the battery in an unconfined area. Do not
charge the battery in a garage or closed room where there
is not sufficient ventilation.
Nonmaintenance batteries: Only do a slow charge (5 A or
less). Charging at a quicker rate is dangerous. The battery
may explode causing personal injuries.
Maintenance type batteries: Be sure to remove the vent
plugs before recharging.
NOTICE
Never recharge the battery while the engine is running. Also,
make sure all accessories are turned off.

ELECTRICAL COMPONENTS
264
REPLACING LIGHT BULBS
The illustration on the following pages show the locations of light
bulbs. If it is necessary to replace a bulb, take your vehicle to your
Lexus dealer as soon as possible. Use bulbs with the bulb numbers
and wattage ratings given in the table.
CAUTION
Do not disassemble, repair or take apart the low beam
headlight bulbs, connector, power supply circuits and
rotated components. Or you may be injured by electric
shocks. Call your dealer when the headlights fail to work
or have to be replaced or disposed of.
Halogen bulbs have pressurized gas inside and require
special handling. They can burst or shatter if scratched or
dropped. Hold a bulb only by its plastic or metal case. Do
not touch the glass part of a bulb with bare hands.
NOTICE
Only use a bulb of the listed type.
LIGHT LOCATION
64L022-4
Light Bulbs Bulb No. W Type
1 Headlights (High beam) HB3 60 A
2 Parking lights 5 D
3 Headlights (Low beam)
Discharge bulbs D2R 35 B
Halogen bulbs HB4 51 C
4 Front turn signal lights 21 D
5 Front side marker lights 5 D
6 Fog lights HB4 51 C

BODY
272Aluminum wheels: Use only a mild soap or neutral detergent.
Urethane bumpers and side moldings: Wash carefully. Do not
scrub with abrasive cleaners. The bumper and side molding faces are
soft.
Road tar: Remove with turpentine or cleaners that are marked safe
for painted surfaces.
NOTICE
Do not use gasoline or strong solvents, which may be toxic or
cause damage.
3. Rinse thoroughly dried soap can cause streaking. In hot weather
you may need to rinse each section right after you wash it.
4. To prevent water spots, dry the vehicle using a clean soft cotton
towel. Do not rub or press hard you might scratch the paint.
Automatic car wash
Your vehicle may be washed in an automatic car wash, but remember
that the paint can be scratched by some type of brushes, unfiltered
washing water, or the washing process itself. Scratching reduces
paint durability and gloss, especially on darker colors. The manager
of the car wash should be able to advise you whether the process is
safe for the paint on your vehicle.
Waxing your Lexus
Polishing and waxing is recommended to maintain the original
beauty of your Lexus’ finish.
Once a month or if the vehicle does not repel water well, apply wax.
1. Always wash and dry the vehicle before you begin waxing, even
if you are using a combined cleaner and wax.
2. Use a good quality polish and wax. If the finish has become
extremely weathered, use a carcleaning polish, followed by a
separate wax. Carefully follow the manufacturer’s instructions and
precautions. Be sure to polish and wax the chrome trim as well as
the paint.
3. Wax the vehicle again when water does not bead but remains on
the surface in large patches.

BODY
274
Synthetic Leather Areas
(Dash and sun visors)
The synthetic leather areas may be easily cleaned with a mild
soap or detergent and water.
First vacuum over the upholstery to remove loose dirt. Then, using
a sponge or soft cloth, apply the soap solution to the synthetic leather.
After allowing it to soak in for a few minutes to loosen the dirt,
remove the dirt and wipe off the soap with a clean damp cloth. If all
the dirt does not come off, repeat the procedure. Commercial
foamingtype cleaners are also available which work well. Follow
the manufacturer’s instructions.
NOTICE
Do not use solvent, thinner, gasoline or window cleaner on the
interior.
Carpets, Windows and Seat Belts
Begin by vacuuming thoroughly to remove as much dirt as possible.
Several types of foam cleaners are available; some are in aerosol
cans and others are powders or liquids which you mix with water to
produce a foam. To shampoo the carpets, use a sponge or brush to
apply the foam. Rub in overlapping circles. Do not apply water
the best results are obtained by keeping the carpet as dry as possible.
Read the shampoo instructions and follow them closely.
The seat belts may be cleaned with mild soap and water or with
lukewarm water.
Use a cloth or sponge. As you are cleaning, check the belts for
excessive wear, fraying or cuts.
NOTICE
Use a good foamtype shampoo to clean the carpets.
Do not use dye or bleach on the belts it may weaken them.
The windows may be cleaned with any household window
cleaner.
When cleaning the inside of the rear window, be careful not
to scratch or damage the heater wires.

INDEX (E G)
280
Checking the coolant level 233. . . . . . . . . . . .
Coolant 233. . . . . . . . . . . . . . . . . . . . . . . . . . .
Coolant temperature gauge 34. . . . . . . . . . . . .
Emission control device 155. . . . . . . . . . . . . .
Engine compartment 220 . . . . . . . . . . . . . . . . .
Exhaust gas caution 156. . . . . . . . . . . . . . . . . .
Hood release 62. . . . . . . . . . . . . . . . . . . . . . . .
Oil consumption 229. . . . . . . . . . . . . . . . . . . .
Oil level 230. . . . . . . . . . . . . . . . . . . . . . . . . . .
Overheating 196. . . . . . . . . . . . . . . . . . . . . . . .
Spark plugs 226. . . . . . . . . . . . . . . . . . . . . . . .
Starting procedure 159. . . . . . . . . . . . . . . . . . .
Threeway catalytic converter 155. . . . . . . . .
Engine coolant, Winter driving tips 182. . . . . . .
Engine immobiliser system 10. . . . . . . . . . . . . .
Engine oil, Winter driving tips 182. . . . . . . . . . .
Engine coolant temperature gauge 34. . . . . . . . .
Exhaust gas caution 156. . . . . . . . . . . . . . . . . . . F
Facts about engine oil consumption 229. . . . . . .
Flasher, Headlight 5, 24. . . . . . . . . . . . . . . . . . .
Flat tire
After changing wheels 204. . . . . . . . . . . . . . . .
Changing tires 202. . . . . . . . . . . . . . . . . . . . . .
If you have a flat tire 197 . . . . . . . . . . . . . . . . .
Jack point 201. . . . . . . . . . . . . . . . . . . . . . . . .
Jacking precautions 197. . . . . . . . . . . . . . . . . .
Jacking up 201. . . . . . . . . . . . . . . . . . . . . . . . .
Loosening wheel nuts 201 . . . . . . . . . . . . . . . . .
Lowering vehicle 203. . . . . . . . . . . . . . . . . . . .
Reinstalling wheel ornament 204. . . . . . . . . . .
Removing wheel ornament 200. . . . . . . . . . . .
Wheel block 200. . . . . . . . . . . . . . . . . . . . . . .
Wheel nuts 201. . . . . . . . . . . . . . . . . . . . . . . . .
Floor mat 58. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fluid level
Brake 239. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine coolant 233. . . . . . . . . . . . . . . . . . . . . .
Power steering 240. . . . . . . . . . . . . . . . . . . . . .
Washer fluid 261. . . . . . . . . . . . . . . . . . . . . . .
Fog light 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Foreign countries, Operation in 181. . . . . . . . . . Front seat
Lumbar support 73. . . . . . . . . . . . . . . . . . . . . .
Position 71. . . . . . . . . .
Seat cushion angle and height 72. . . . . . . . . . .
Seatback angle 72. . . . . . . . . . . . . . . . . . . . . . .
Fuel
Filler door opener 65. . . . . . . . . . . . . . . . . . . .
Fuel economy 189. . . . . . . . . . . . . . . . . . . . . .
Fuel information 227. . . . . . . . . . . . . . . . . . . .
Gauge 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MTBE 228. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation in foreign countries 181. . . . . . . . . .
Tank cap 65. . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse
Blade type fuses 258. . . . . . . . . . . . . . . . . . . .
Cartridge type fuses 260. . . . . . . . . . . . . . . . . .
Fuse locations 249. . . . . . . . . . . . . . . . . . . . . . . .
Fuse box 220. . . . . . . . . . . . . . . . . . . . . . . . . . . .
G
Garage door opener 54. . . . . . . . . . . . . . . . . . . .
Gas station information Inside back cover. . . . .
Gauge
Engine coolant temperature 34. . . . . . . . . . . . .
Fuel 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glovebox 54. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Good driving practice 166 . . . . . . . . . . . . . . . . . .

GAS STATION INFORMATION
Fuel selection:
Select premium unleaded gasoline with an Octane Rating of 91
(Research Octane Number 96) or higher for optimum engine
performance. However, if such premium type cannot be
obtained, you may temporarily use unleaded gasoline with an
Octane Rating as low as 87 (Research Octane Number 91).
Fuel tank capacity:
85 L (22.5 gal., 18.7 lmp.gal.)
Engine oil:
API SH, ”EnergyConserving II” or SJ, ”EnergyConserving”
multigrade engine oil or ILSAC multigrade engine oil.
Recommended oil viscosity SAE 5W30 if normal
temperatures are below 38C (100F)
Oil capacity: L (qt., lmp.qt.)
Drain and refill
with filter 5.6 (5.9, 4.9)
without filter 5.3 (5.6, 4.7)
See page 230 for detailed information.
Engine coolant:
Capacity: 10.8 L (11.4 qt, 10.4 lmp.qt.)
Coolant type Ethylene glycol coolant (Do not use alcohol
coolant.)
For checking the engine coolant, see page 233.
For changing the engine coolant, see the label on the coolant
reservoir.Automatic transmission:
Fluid type Automatic transmission fluid Type TIV or
equivalent
Tire information:
See page 241 through 247 for detailed information.
Tire pressure:
Tire size: P225/60R16 97V
cold tires
kPa (kgf/cm
2
or bar, psi)
Vehicle loaded up
Vehicle load up to vehicle capacity
up to occupants weight
Front tires 200 (2.0, 29) 220 (2.2, 32). . . . . . . . . . . . .
Rear tires 200 (2.0, 29) 220 (2.2, 32). . . . . . . . . . . . .
For sustained high speeds above 160 km/h (100 mph), in
countries where such speeds are permitted by law, add 80 kPa
(0.9 kgf/cm
2, 0.8 bar, 12 psi) to the front tires and rear tires, but
never exceed the maximum cold tire pressure molded on the tire
sidewall.
LS400 (U) 98