radio LEXUS LS430 2005 User Guide

AUDIO
267

The following products may not be playable on your CD
player.
Copy−protected CD
CD− R (CD− Recordable)
CD−RW (CD− Re−writable)
CD−ROM
 Your CD player is intended for use with 12 cm (4.7 in.) CDs
only.
Radio operation
(a) Listening to the radio
20L363
Push these buttons to choose either an AM or FM station.
“AM”, “FM1”, “FM2” or “FM TYPE” appears on the d\
isplay.
If your vehicle is equipped with satellite radio broadcast
system, when you push the “AM·SAT” button, “AM”,
“SAT1”, “SAT2” or “SAT3” station appears on the display. For
details about satellite radio broadcast, see “Radio operation
(XM satellite radio broadcast)” on page 272

AUDIO
268
20L128
Push this button on the upper side to step up the station
band or on the lower side to step down.
Your radio automatically changes to stereo reception when a
stereo broadcast is received. “ST” appears on the display. If
the signal becomes weak, the radio reduces the amount of
channel separation to prevent the weak signal from creating
noise. If the signal becomes extremely weak, the radio
switches from stereo to mono reception. In this case, “ST”
disappears from the display.(b) Presetting a station
20L129
1. Tune in the desired station.
2. Push
one of the station selector buttons ( 16 ) and hold
it until a beep is heard. This sets the station to the button
and the button number ( 16 ) appears on the display.
Each button can store one AM station and two FM stations. To
change the preset station to a different one, follow the same
procedure.
The preset station memory is cancelled when the power
source is interrupted by battery disconnection or a blown fuse.

AUDIO
269
(c) Selecting a station
Tune in the desired station using one of the following methods.
20L130a
Preset
tuning: Push the button ( 1 −6 ) for the station you want.
The button number ( 1− 6 ) and station frequency appear on the
display.
Manual tuning: Push the “TUNE SEEK” button briefly. Each
time you push the button, the radio will step up or down to
another frequency.
Seek tuning: Push the “TUNE SEEK” button and hold it until
you hear a beep. The radio will begin seeking up or down for
a station of the nearest frequency and will stop on reception.
Each time you push the button, the stations will be searched
automatically one after another.
20L139a
To scan all the frequencies: Push the “SCAN” button briefly.
“SCAN” appears on the display. The radio will find the next
station up the band, stay there for a few seconds, and then
scan again. To select a station, push the “SCAN” button a
second time.
To scan the preset stations: Push the “SCAN” button and
hold it until you hear a beep. “P .SCAN” appears on the display.
The radio will tune in the next preset station up the band, stay
there for a few seconds, and then move to the next preset
station. To select a station, push the “SCAN” button a second
time.

AUDIO
270(d) RDS (Radio Data System)
20L364
Program type:
When you push the TYPE “
”
or “” button, the current
program type receiving from the RDS station appears on the
display.
If the radio receives no RDS stations, “NO PTY” appears on the
display.
Each time you push the TYPE “
” or “” button, the program
type changes as in the following:
 ROCK
 EASY LIS (Easy listening)
 CLS/JAZZ (Classical music and jazz)
 R&B (Rhythm and Blues)
 INFORM (Information)
 RELIGION 
MISC
 ALERT (Emergency message)
While you are listening to a program type, you can operate the
“TUNE SEEK” or “SCAN” function.
20L406
Push the “TUNE SEEK” or “SCAN” button. The radio seeks or
scans the station in the relevant program type. (See page 269
for details.)

AUDIO
271
Traffic program: A station that regularly broadcasts
traffic information is automatically located.
When you push the “TRAF” button, “TRAF SEEK” appears on
the display and the radio will start seeking any traffic program
station.
If no traf
fic program station is found, “NO TRAF INFO” appears
on the display for a few seconds and the display returns to the
previous mode. Radio text:
20L177a
If the radio receives radio text, “MSG” appears on the display.
When you push the “MSG” button, a message is displayed.
In case a message is more than a line, hold the “MSG” button.
The rest of the message is displayed.
When the system
can show the station name, “RDS” appears
on the display. Each time you push the “MSG” button, the
indication changes from the band to the station name to radio
text in this order. After six seconds, the indication returns to the
band.

AUDIO
272
Radio operation (XM satellite radio broadcast)
To listen to a satellite radio broadcast in your vehicle, an
additional genuine Lexus satellite receiver and antenna (or
equivalents) must be purchased and installed. A subscription
to the XM satellite radio service is also necessary.
(a) How to subscribe to an XM satellite radio
An XM satellite radio is a tuner designed exclusively to receive
broadcasts provided under a separate subscription.
Availability is limited to the 48 contiguous states.
How to subscribe:
You must enter into a separate service agreement with the XM
radio in order to receive satellite broadcast programming in the
vehicle. Additional activation and service subscription fees
apply that are not included in the purchase price of the vehicle
and optional digital satellite tuner. For complete information on
subscription rates and terms, or to subscribe to the XM radio,
visit XM on the web at www.xmradio.com
or call an XM’s
Listener Care at (800) 852 −9696. The XM radio is solely
responsible for the quality, availability and content of the
satellite radio services provided, which are subject to the terms
and conditions of the XM radio customer service agreement.
Customers should have their radio ID ready; the radio ID can
be found by tuning to “channel 000” on the radio. For details,
see “Displaying the radio ID” below.
All fees and programming are the responsibility of the XM
satellite radio and are subject to change. Satellite tuner technology notice:
Lexus satellite radio tuners are awarded Type Approval
Certificates from XM
Satellite Radio Inc. on “March 10, 2003”
and “April 15, 2003” as proof of compatibility with the services
offered by the XM satellite radio.
(b) Displaying the radio ID
Each XM tuner is identified with a unique radio ID. You will
need the radio ID when activating XM service or when
reporting a problem.
If you select the “CH 000” using the “TUNE” button, the ID cod\
e
of 8 alphanumeric characters appears. If you select another
channel, display of the ID code is canceled. The channel (000)
alternates the display between the radio ID and the specific
radio ID code.

AUDIO
273
(c) Listening to the satellite radio
20L469
Push the “AM·SAT” button to choose a SAT station.
Besides “AM”, “SAT1”, “SAT2” or “SAT3” appears on the
display.
20L471a
Push this button to select the next or previous channel.
If you push and hold the button, you can rapidly scroll forward
or down through the channels. When displaying the channel
category by the “TYPE” button, pushing the “TUNE SEEK”
button lets you select the next or previous channel within the
currently selected type.

AUDIO
275
20L139a
To scan the currently selected channel category : Push the
“SCAN” button briefly. “SCAN” appears on the display. The
radio will find the next channel in the same channel category
up the band, stay there for a few seconds, and then scan again.
To select a channel, push the “SCAN” button a second time.
To scan the preset channels: Push the “SCAN” button and
hold it until you hear a beep. “P .SCAN” appears on the display.
The radio will tune in the next preset channel , stay there for a
few seconds, and then move to the next preset channel. To
select a channel, push the “SCAN” button a second time. (f) Channel category
20L364
When you push the TYPE “”
or “” button, the current
channel category appears on the display.
When the channel category appears, push either “
” or “”
button to switch to the next or previous category.

AUDIO
277
(h) If the satellite radio tuner malfunctions
When
problems occur with the XM tuner, a message will appear on the display. Referring to the table below to identify the problem,
take the suggested corrective action.
ANTENNA
The XM antenna is not connected. Check whether the XM antenna cable is \
attached securely.
A short−circuit occurs in the antenna or the surrounding antenna cable. See a L\
exus certified
dealer.
UPDATING
You have not subscribed to the XM satellite radio. The radio is being up\
dated with the latest
encryption code. Contact the XM satellite radio for subscription inform\
ation. When a contact is
canceled, you can choose the “CH000” and all free −to− air channels.
The premium channel you selected is not authorized. Wait for about 2 seconds until the radio
returns to the previous channel or “CH001”. If it does not change\
automatically, select another
channel. If you want to listen to the premium channel, contact the XM s\
atellite radio.
NO SIGNALThe XM signal is too weak at the current location. Wait until your vehicle reaches a location
with a stronger signal.
LOADINGThe unit is acquiring audio or program information. Wait until the unit has received the informa-
tion.
OFF AIRThe channel you selected is not broadcasting any programming. Select an\
other channel.
−−−−−There is no song/program title or artist name/feature associated with th\
e channel at that time.
No action needed.
−−−
The channel you selected is no longer available. Wait for about 2 seconds until the radio re-
turns to the previous channel or “CH001”. If it does not change a\
utomatically, select another
channel.
The XM Listener Care Center is also available on the phone, please call \
(800) 852 −9696 during the following hours:
Monday – Saturday: 7 a.m. – 1 a.m. Sunday: 12 p.m – 12 a.m.

AUDIO
278
NOTICE
This equipment has been tested and found to comply
with the limits for a class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
Information to user
Alternation or modifications carried out without
appropriate authorization may invalidate the user’s
right to operate the equipment.
NOTICE
This XM tuner supports “Audio Services” (Music and
Talk) of only XM satellite radio and “Text Information”*
linked to the respective audio services.
*Text Information includes, Channel Name, (Artist)
Name, (Song) Title and Category Name.