warning LEXUS LS430 2005 Service Manual

OCCUPANT RESTRAINT SYSTEMS
192
16L656
 1Collision from the front
2Collision from the rear
3Vehicle rollover
The SRS side airbags and curtain shield airbags are not
generally designed to inflate if the vehicle is involved in a
front or rear collision, if it rolls over, or if it is involved in
a lowspeed side collision.
16L657
 1 Curtain shield airbag module (airbag and inflator)
2Side airbag module (airbag and inflator)
3Curtain shield airbag sensor assembly
4Side and curtain shield airbag sensor assembly
5SRS warning light
6Airbag sensor assembly
The SRS side airbag and curtain shield airbag system consists
mainly of the above components, and their locations are
shown in the illustration.
The SRS side airbag and curtain shield airbag system is
controlled by the airbag sensor assembly. The airbag sensor
assembly consists of a safing sensor and airbag sensor.

OCCUPANT RESTRAINT SYSTEMS
197
NOTICE
Do not perform any of the following changes without
consulting your Lexus dealer. Such changes can
interfere with proper operation of the SRS side airbag
and curtain shield airbag system in some cases.
Installation of electronic devices such as a mobile
twoway radio, cassette tape player or CD player.
 Modification of the suspension system.
 Modification of the structure of the passenger
compartment.
 Repairs made on or near the console or front seat.
16L330b
The indicator comes on when the ignition switch is turned
to the “ON” position. It goes off after about 6 seconds.
This means the SRS side airbags and curtain shield
airbags are operating properly.
This warning light system monitors the airbag sensor
assembly, front airba g sensors, side and curtain shield airbag
sensor assemblies, curtain shield airbag sensor assemblies,
driver’s seat position sensor, driver’s seat belt buckle switch,
occupant detection sensor, front passenger’s seat belt buckle
switch, seat belt pretensioner assemblies, inflators, warning
light, interconnecting wiring and power sources. (For details,
see “Service reminder indicators and warning buzzers” on
page 82.)

SECTION 3 – 1
295
STARTING AND DRIVING
Starting and driving
Three−way catalytic converters296
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine exhaust caution 297
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before starting the engine 298
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Smart ignition system with steering lock 298
. . . . . . . . . . . . . . . . . . . . .
Ignition switch with steering lock 301
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking brake 304
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . .
How to start the engine 304
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic transmission 305
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electronic throttle control system 315
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Lexus park assist system 316
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear view monitor system 323
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cruise control 326
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . .
Dynamic radar/laser cruise control 329
. . . . . . . . . . . . . . . . . . . . . . . . .
Electronically modulated air suspension 360
. . . . . . . . . . . . . . . . . . . . .
Traction control system 362
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vehicle stability control system 364
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake system 366
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . .
Tire pressure warning system 370
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake pad wear limit indicators 373
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pre−collision safety system 374
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

STARTING AND DRIVING
299
31L346a
When you enter the vehicle carrying a sm art key and push
the ignition switch, the electronic code in the key is
automatically checked as to whether it corresponds to the
registered ID code for the vehicle. The key indicator light
comes on, the steering column lock is released, and the
engine immobilizer system is cancelled.
At this time, the security indicator light goes off and you can
start the engine when you turn the ignition switch and the key
indicator light does not come on. When you turn the ignition
switch, turn it slowly and surely. If you turn it quickly, it may
become stuck. To free it, see the following “If the ignition switch
seems to be stuck”.
If you push the ignition switch when the smart key is not within
the effective range of the smart key system, a warning tone
sounds and “Key is not Detected” appears on the display. If the ignition switch seems to be stuck:
To free the ignition switch, perform the following:
31L638
1. Push the ignition switch.
31L639
2. Be sure to push the ignition switch while turning the
steering wheel slightly in either direction, and then turn
the switch.

STARTING AND DRIVING
300“START” Starter motor on. The ignition switch will
return to the “ON” position when released.
For starting tips, see page 304.
“ON” Engine on and all accessories on.
This is the normal driving position.
NOTICE
Do not leave the ignition switch in the “ON” position if
the engine is not running. The battery will discharge
and the electronic ignition system could be damaged.
“ACC” Accessories such as the radio operate, but the
engine is off.
31L347
“LOCK” Engine is off and the steering wheel is locked.
When
you leave your vehicle, be sure to turn the ignition switch
to the “LOCK” position and carry the smart key.
 If you open the driver’s door without returning the ignition
switch to the “LOCK” position, beeps keep sounding while
the door is opened.
 If you close a door to leave your vehicle while carrying a key
on which the ignition switch has not been returned to the
“LOCK” position, “Key is not Detected” appears on the
multi−information display, a warning tone sounds inside and
beeps sound outside.
 If the selector lever is in a position other than “P”, you cannot
turn the ignition switch to the “LOCK” position. At this time,
when you open the driver’s door and are going to get out of
the vehicle, “Shift to P Range” appears on the
multi−information display and a warning tone sounds inside.

STARTING AND DRIVING
310“4” (fourth range):
The most suitable gear is automatically
selected between first and fourth gears according to vehicle
speed and driving conditions. In the “4” (fourth range)
position, the automatic transmission system will select the
most suitable gear to handle current running conditions
such as hill climbing, hard towing, etc.
“3” (third range): The most suitable gear is automatically
selected between first and third gears according to vehicle
speed and driving conditions. This range is best used when
stronger engine braking is necessary.
“2” (second range): First or second gear will automatically
be selected according to vehicle speed and driving
conditions. This range is to be used when engine braking
stronger than that of the “3” (third range) position is
necessary.
“1” (first range): This gear is fixed in first regardless of
vehicle speed or driving conditions. This range is to be used
when maximum engine braking is necessary.
If you attempt to downshift the transmission when it is not
possible to downshift due to high vehicle speed, a warning tone
sounds twice. 
Maximum allowable speeds
To get on a highway or to pass slower traffic, maximum
acceleration may be necessary. Make sure you observe the
following maximum allowable speeds in each range:
range km/h (mph)1 59 (36)
2 100 (62)
3 146 (90)
NOTICE
Do not downshift if you are going faster than the
maximum allowable speed for the next lower range.
 “S” mode indicator light
“S” mode allows you to use the shift range positions.
The “S” mode indicator light comes on when the selector
lever is shifted into the “S” position. When the “S” mode
indicator light does not come on even with the selector lever
moved to the “S” position, there may be a problem
somewhere in the system. Have your vehicle
checked/repaired by your Lexus dealer as soon as
possible. In this case, you can drive in the same condition
as in the “D” position.

STARTING AND DRIVING
317
31L340
You can use this system in either of the following ways.
Push the main switch of the Lexus park assist system with
the ignition on. A beep sounds for one second. After the
system self− check is performed, the Lexus park assist
system screen appears for 2 seconds.
 Push the main switch of the Lexus park assist system and
turn the ignition on. The Lexus park assist system screen
appears for 2 seconds and a system self −check is
performed. At this time, a beep does not sound.
If an error is detected in the Lexus park assist system while
self−checking, beeps sound and the message appears in the
multi− information display. For details, see “Lexus park assist
system failure warning” on page 319. Up to 4 indicator bars are shown on the front and rear sides of
the vehicle mark and up to 3 indicator arcs are shown on each
corner of the vehicle mark. The number of indicators shows
the approximate range up to the obstacle. The indicator marks
disappear one
−by−one as your vehicle comes closer to the
obstacle. Also, as you get closer to the obstacle, the beeping
interval becomes shorter.
To turn off the system, push the main switch again.
NOTICE
 If an accident should occur, the sensors will be
affected, resulting in a system failure.
 If the indicators remain on the display but you do not
hear a beeping sound, the system may be
malfunctioning. Contact your Lexus dealer.

STARTING AND DRIVING
319
31L149b
Corner obstacles
Depending on the distance between your vehicle and the
obstacle, the display and beeps change as follows:
1 About 37.5 cm (1.1 ft.) to about 50 cm (1.5 ft.): 3 arcs
appear on the corner of the vehicle mark where the
obstacle is detected. At this time, the beeps remind you
that your vehicle is getting closer to the obstacle by
sounding intermittently.
2 About 25 cm (0.8 ft.) to about 37.5 cm (1.1 ft.): The
number of arcs will decrease from 3 to 2. The beeps
sound at shorter intervals than in step
1.
3 Less than about 25 cm (0.8 ft.): The number of arcs will
decrease from 2 to 1, and the bar blinks while the beeps
sound continuously.
Lexus park assist system failure warning
31L351
The system self check is automatically performed when
the Lexus park assist system is turned on. At this time if
an error is detected, the master warning light comes on
accompanied by 5 beeps, the faulty sensor blinks and
either of the following messages appear in the
multiinformation display.
 “Check Park Sonar”
 “Clean Park Sonar”
The sensors operate individually. When one sensor is
malfunctioning, you will notice sounding beeps and blinking
indicators to show that it is malfunctioning. If another sensor
detects an obstacle during this time, the approximate distance
to the obstacle will be shown by that sensor.

STARTING AND DRIVING
321
CAUTION
Do not install an accessory or the like within the sensor
detection range. Doing so may cause the Lexus park
assist system to malfunction, resulting in an accident.
NOTICE
The sensors do not detect an obstacle just under the
bumper. A short object, thin stake or the like will be
detected once but might not be detected as your
vehicle gets very close to such an object.
 If an obstacle is very close to your vehicle, it might
not be detected.
 If a sensor is subjected to a strong impact, it will not
operate properly.
The Lexus park assist system may not work properly in
the following cases:
When icicles, snowflakes or mud gets on the sensors.
If removed, the system will work properly.
 When the sensor is frozen.
If deiced, the system will work properly.
 When the sensor is covered with something.
If removed, the system will work properly. Especially in cold weather, a malfunction warning screen may
appear on
the display due to frozen sensors. If the “Clean Park
Sonar” appears on the display, be sure to clean the sensor. If
the “Clean Park Sonar” appears despite no mud, ice or
snowflakes on the sensor, the sensor might have
malfunctioned. Have your vehicle checked by your Lexus
dealer.
In the following conditions, the detection range may be
affected:
 When you stop your vehicle in extreme hot or cold weather.
 Foreign matter such as snowflakes or mud gets on the
sensor.

STARTING AND DRIVING
328
2Cancelling the preset speed
You can cancel the preset speed by either of the following:
a. Pulling the control lever in the “CANCEL” direction.
b. Depressing the brake pedal.
c. Pushing the “ON −OFF” button.
If the vehicle speed falls below about 40 km/h (25 mph), the
preset speed will be automatically cancelled.
If the vehicle speed drops 16 km/h (10 mph) below the preset
speed, the preset speed will also automatically be cancelled.
If the slip indicator light blinks and a warning tone sounds, the
preset speed will be automatically cancelled.
If the preset speed automatically cancels out for other than the
above reasons, do not operate the cruise control. Although it
is no problem to continue driving, have your vehicle checked
by your Lexus dealer at the earliest opportunity.
3 Resetting to a faster speed
Press the control lever upward in the “+ RES” direction and
hold it. Release the lever when the desired speed is attained.
While the lever is held upward, the vehicle will gradually gain
speed.
When the difference between the actual vehicle speed and the
set speed is less than 5 km/h (3 mph), the set speed can be
increased 1. 6 km/h (1 mph) each time by pressing the control
lever upward in the “+ RES” direction quickly within 0.6
seconds. However, a quicker way to reset is to accelerate the vehicle
and then press the control lever downward in the “– SET”
direction.
4
Resetting to a slower speed
Press the co ntrol lever downward in the “– SET” direction and
hold it. Release the lever when the desired speed is attained.
While the lever is held downward, the vehicle speed will
gradually decrease.
When the difference between the actual vehicle speed and the
set speed is less than 5 km/h (3 mph), the set speed can be
lowered 1.6 km/h (1 mph) each time by pressing the control
lever downward in the “– SET” direction quickly within 0.6
seconds.
However, a quicker way to reset is to depress the brake pedal
and then press the control lever downward in the “– SET”
direction.
With the cruise control on, even if you downshift the
transmission from the “D” position or “6” (sixth range) to the “5”\
(fifth range), or from the “D” position or “5” (fifth ran\
ge) to the
“4” (fourth range), engine braking will not be enabled because
the cruise control is not cancelled. To decrease the vehicle
speed, reset to a slower speed with the cruise control lever or
depress the brake pedal. If you use the brake pedal, cruise
control is cancelled.