ignition LEXUS LX470 2006 Owners Manual

STARTING AND DRIVING
300
31x608
Tire pressure warning light
The tire pressure warning light comes on when the ignition
switch is turned to the “ON” position and goes off after a few
seconds. This means the tire pressure warning light is
operating properly. If the tire inflation pressure becomes low,
the light comes on again. In this case, adjusting the tire
inflation pressure will turn off the light after a few minutes. If the
light blinks, the tire pressure warning system is not working
properly.
Indicator status
MeaningsDo this
ONTire inflation
pressure is lowAdjust the tire
inflation pressure
BlinkingTire pressure
warning system
malfunctionHave the system
checked at your
Lexus dealer
CAUTION
If the tire pressure warning light comes on, be sure to
observe the following precautions. Failure to do so
could cause loss of vehicle control and result in death
or serious injury.
 Stop your vehicle in a safe place as soon as possible.
Adjust the tire inflation pressure immediately.
 If the tire pressure warning light comes on even after
tire inflation pressure adjustment, it is probable that
you have a flat tire. Check the tires. If the tire is flat,
change to the spare tire and have the flat tire repaired
by the nearest Lexus dealer.
 Avoid abrupt maneuvering and braking. If the vehicle
tires deteriorate, you could lose control of the
steering wheel or the brakes.

STARTING AND DRIVING
303
If the tire pressure warning light blinks...
31x609
If the tire pressure warning light blinks when the ignition
switch is turned to the “ON” position, the tire pressure
warning system is not working properly.
The system will be disabled in the following conditions:
(When the condition becomes normal, the system will work
properly.)

If tires not equipped with tire pressure warning valves and
transmitters are used.
 If the ID code on the tire pressure warning valves and
transmitters is not registered.
 If electronic devices or facilities using similar radio wave
frequencies are nearby.
 If a radio set at similar frequencies is in use in the vehicle. 
If a window tint that affects the radio wave signals is
installed.
 If the tire pressure warning select switch is set to a dif ferent
tire setting.
 If there is a lot of snow or ice on the vehicle, in particular
around the wheels or wheel housings.
 If non− genuine Lexus wheels are used.
 If tire chains are used.
 If the spare tire is in a location subject to poor radio wave
signal reception.
 If the tire inflation pressure is 500 kPa (5.1 kgf/cm2
or bar,
73 psi) or higher.
If the tire pressure warning light blinks frequently when the
ignition switch is turned to the “ON” position, have it checked
by your Lexus dealer.
Even if you use genuine wheels, the tire pressure warning
system may not work properly with some types of tires.
Pushing the tire pressure warning reset switch should not turn
off the tire pressure warning light.

STARTING AND DRIVING
306To initialize the system, perform the following:
1. Park the vehicle in a safe place and turn the ignition switch
to the “OFF” position.
2. Adjust the pressure of all the installed tires to the specified
cold tire inflation pressure level. (See “Tire and wheels” on
page 420.)
3. Turn the ignition switch to the “ON” position.
4. Push and hold the tire pressure warning reset switch until
the tire pressure warning light blinks slowly three times.
5. Wait for a few minutes with the ignition switch “ON”, and
then turn the ignition switch to the “OFF” position.
If you push the tire pressure reset switch while the vehicle is
moving, initialization is not performed.
If you push the tire pressure reset switch accidentally and
initialization is performed, adjust the tire inflation pressure to
the specified level and initialize the system again.
31x609
If the tire pressure warning light does not blink slowly three
times when you push and hold the reset switch, initialization
has failed and the tire pressure warning system may not work
properly. In this case, initialize the system again. If
initialization
cannot be performed, have the system checked at
your Lexus dealer.
CAUTION
Do not push the reset switch without first adjusting the
tire inflation pressure to the specified level. Otherwise,
the tire pressure warning light may not come on even if
the tire inflation pressure is low, or it may come on when
the tire inflation pressure is actually normal.

DRIVING TIPS
316Make sure the engine oil viscosity is suitable for the cold
weather.
See page 412 for recommended viscosity. Leaving a heavy
summer oil in your vehicle during winter months may cause
harder starting. If you are not sure about which oil to use, call
your Lexus dealer
− they will be pleased to help.
Check the electronic ignition system for loose
connections or obvious damage.
Keep the door locks from freezing.
Squirt lock de −icer or glycerine into the locks to keep them from
freezing.
Use a washer fluid containing an antifreeze solution.
This product is available at your Lexus dealer and most auto
parts stores. Follow the manufacturer’s directions for how
much to mix with water.
NOTICE
Do not use engine antifreeze or any other substitute
because it may damage your vehicle’s paint.
Do not use your parking brake when there is a possibility
it could freeze.
When parking, put the transmission into “P” and block the front
wheels. Do not use the parking brake, or snow or water
accumulated in and around the parking brake mechanism may
freeze the parking brake, making it hard to release. Keep ice
and snow from accumulating under the fenders.
Ice and snow built up under your fenders can make steering
difficult. During bad winter driving, stop and check under the
fenders occasionally.
Depending on where you are driving, we recommend you
carry some emergency equipment.
Some of the things you might put in the vehicle are tire chains,
window scraper, bag of sand or salt, flares, small shovel,
jumper cables, etc.

DRIVING TIPS
323
Trailer lights
32x601b
Your vehicle is equipped with a wire harness stored in the
rear end underbody. Some models are fitted with a socket
for trailer lights under the rear bumper. Use either of them
to connect and operate the trailer lights. However, the trailer
lights must comply with federal, state/provincial and local
regulations. See your local recreational vehicle dealer or
rental agency for the correct type of wiring and relays for
your trailer. Check for correct operation of the turn signals
and stop lights each time you hitch up. Direct splicing may
damage your vehicle’s electrical system and cause a
malfunction of your lights.
Breakin schedule
 Lexus recommends that you do not tow a trailer with a new
vehicle or a vehicle with any new power train component
(engine, transmission, differential, wheel bearing, etc.) for
the first 800 km (500 miles) of driving.
Maintenance
 If you tow a trailer, your vehicle will require more frequent
maintenance due to the additional load. For this
information, please refer to the scheduled maintenance
information in the “Owner’s Manual Supplement /
Scheduled Maintenance”.
 Retighten all fixing bolts of the towing ball and bracket after
approximately 1000 km (600 miles) of trailer driving.
Connecting a trailer
Stop your vehicle and a trailer in line and perform the following:
1. Put the active height control suspension in the “LO” (low)
mode. Turn the ignition switch off or push the height control
switch to turn off the active height control suspension.
2. Connect a trailer.
3. Turn the ignition switch on or push the height control switch
to turn on the active height control suspension. Select the “N”
(normal) mode with the height select switch.
When a vehicle loaded with 4 occupants tows a trailer of about
1800 kg (4000 lb.) with more than about 180 kg (400 lb.) tongue
load, the normal mode may not be selected with the height
control indicator “LO”. However, there is no problem to
continue normal driving. Drive with sufficient care because of
large load.

DRIVING TIPS
324
Disconnecting a trailer
Stop your vehicle and a trailer in line and perform the following:
1. Put the active height control suspension in the “LO” mode.
(Make sure the vehicle height is in the “LO” mode by pushing
the height select switch on the “
”side.)
2. Turn the ignition switch off or push the height control switch
to turn off the active height control suspension.
3. Set the supporting leg of a trailer on the ground and raise the
hitch by 100 mm (4 in.).
4. Turn the ignition switch on or push the height control switch
to turn on the active height control suspension.
5. Wait for about 20 seconds until the rear vehicle height is
lowered by the automatic leveling function.
6. Make sure the hitch is disconnected. If not, raise the hitch
higher and repeat steps 2 through 5.
7. Move the vehicle forward in the “LO” mode where the hitch
does not touch anything in the “N” mode.
8. Put the active height control suspension in the “N” mode.
Pretowing safety check
 Check that your vehicle remains level when a loaded or
unloaded trailer is hitched. Do not drive if the vehicle has
an abnormal nose −up or nose− down condition, and check
for improper tongue load, overload, worn suspension or
other possible causes.
 Make sure the trailer cargo is securely loaded so that it
cannot shift.
 Check that your rear view mirrors conform to any federal,
state/provincial or local regulations. If they do not, install
required rear view mirrors appropriate for towing purposes.

IN CASE OF AN EMERGENCY
335
NOTICE
Do not pull or pushstart the vehicle. It may damage
the vehicle or cause a collision when the engine starts.
Also the threeway catalytic converter may overheat
and become a fire hazard.
If the engine turns over at its normal speed but will not
start
1. The engine may be flooded because of repeated cranking.
See “(b) Starting a flooded engine” for further instructions.
2. If the engine still will not start, it needs adjustment or repair.
Call a Lexus dealer, Roadside Assistance or Customer
Service Assistance. (See “Foreword”.)
(b) Starting a flooded engine
If the engine will not start, your engine may be flooded
because of repeated cranking.
If this happens, turn the ignition key to “START” with the
accelerator pedal fully depressed, and hold the key at this
position for about 30 seconds. Then the cranking hold function
stops cranking automatically, and you can try starting the
engine with your foot off the accelerator pedal.
If the engine does not start, wait a few minutes and try again.
If the engine still will not start, it needs adjustment or repair.
Call a Lexus dealer, Roadside Assistance or Customer
Service Assistance. (See “Foreword”.)
(c) Jump starting
To avoid serious personal injury and damage to your
vehicle which might result from battery explosion, acid
burns, electrical burns, or damaged electronic
components, these instructions must be followed
precisely.
If you are unsure about how to follow this procedure, we
strongly recommend that you seek help from your Lexus
dealer, Roadside Assistance or Customer Service Assistance.
(See “Foreword”.)

IN CASE OF AN EMERGENCY
355
(d) Emergency towing
40x600a
If towing is necessary, we recommend you to have it done
by your Lexus dealer or a commercial tow truck service.
If towing service is not available in an emergency, your
vehicle may be temporarily towed by a cable or chain
secured to the emergency towing hook. Use extreme
caution when towing the vehicle.
NOTICE
Never tow a vehicle from the rear with four wheels on the
ground. This may cause serious damage to the
transmission.
A driver must be in the vehicle to steer it and operate the
brakes.
Towing in this manner may be done only on hard −surfaced
roads for a short distance and at low speeds. Also, the wheels,
axles, drive train, steering and brakes must all be in good
condition.
CAUTION
Use extreme caution when towing the vehicle. Avoid
sudden starts or erratic driving maneuvers which would
place excessive stress on the emergency towing hook
and towing cable or chain. The hook and towing cable
or chain may break and cause serious injury or damage.
NOTICE
 Do not use front and rear eyelets. It is not designed
for towing.
 Use only a cable or chain specifically intended for
use in towing vehicles. Securely fasten the cable or
chain to the towing hook provided.
Before towing, check that the center differential is unlocked.
(The indicator light must be off with the ignition on.) Release
the parking brake and put the transmission in “N”. The ignition
key must be in “ACC” (engine off) or “ON” (engine running).

IN CASE OF AN EMERGENCY
357
IF YOU CANNOT SHIFT
AUTOMATIC TRANSMISSION SELECTOR LEVER
40X023e
If you cannot shift the selector lever, use the shift lock
override button as follows:
1Turn the ignition key to “LOCK” or “ACC”. Make sure the
parking brake is applied. Pry up the cover with a flathead
screwdriver or equivalent.
40X024e
2 Insert your finger, the screwdriver or equivalent into the
hole to push down the shift lock override button. You can
shift the selector lever while pushing the button.
For your safety, keep the brake pedal depressed.
Be sure to have the system checked by your Lexus dealer as
soon as possible.

IN CASE OF AN EMERGENCY
358
LEXUS LINK SYSTEM(If equipped)
31x522b
 1PTT (Push To Talk) button 2Volume button
3Phone button 4“SERVICES” button
5Emergency button
The Lexus Link System is an invehicle communications
service that provides you with enhanced safety, security
and convenience. With an active subscription you can
push the “SER VICES” button for operator assistance or in
an emergency situation such as a vehicle accident (in
which the airbag was activated), you will automatically be
connected to the Lexus Link Call Center which will assist
you and/or send help 24 hours a day, 7 days a week.
The Lexus Link System can also record your conversation with
the Lexus Link Call Advisor.
Safety information for the Lexus Link System
Important!: Read this information before using the Lexus
Link System.
EXPOSURE TO RADIO FREQUENCY SIGNALS
The Lexus Link System to be installed in your vehicle is a low
power radio transmitter and receiver. When the ignition is
turned to the “ON” position, it receives and also sends out radio
frequency (RF) signals.
In August 1996, the Federal Communications Commission
(FCC) adopted RF exposure guidelines with safety levels for
mobile wireless phones. Those guidelines are consistent with
the safety standards previously set by both U.S. and
international standards bodies.
 ANSI C95.1 (1992)*
1
NCRP Report 86 (1986)*2
ICNIRP (1996)*3
*1: American National Standards Institute
*2: National Council on Radiation Protection and
Measurements
*
3: International Commission on Non −Ionizing Radiation
Protection