lights LEXUS LX470 2006 Owner's Manual

Page 120 of 493

EXTERIOR EQUIPMENT
98
REAR STEP BUMPER
15X600b
The rear step bumper is for rear end protection and easier
stepup loading.
CAUTION
Do not allow more than one person to get on the rear
step bumper at a time. It is designed for only one
person.
 Never drive the vehicle with anyone on the rear step
bumper.
RUNNING BOARD LIGHTS
15x019b
Lighting the running board and the ground helps you
easily to get in and out of the vehicle in the night.
When you unlock any door with a key or wireless remote
control, the lights come on and go out after about 15 seconds
automatically.
Opening any door lights up the lights and closing it goes out
them after 15 seconds. However, if the door remains open, the
lights automatically go out after about 30 minutes.

Page 121 of 493

EXTERIOR EQUIPMENT
99
Cleaning ground lights
15X020
Ground light
If the mud or debris are sticking on the lense covers of the
ground lights, the lights will dim. Wipe off them from the lens
covers with a soft moist cloth periodically.

Page 215 of 493

STEERING WHEEL AND MIRRORS
193
Automatic tiltaway*
16X100f
When the ignition key is removed, the steering column
moves forward away from the driver and also tilts up for
easy exit and entry.
When the key is inserted in the ignition switch, the steering
column returns to the previously set position.NOTE: *This feature can be deactivated. Ask your Lexus
dealer for details.
OUTSIDE REAR VIEW MIRRORS
16X013a
Adjust the mirror so that you can just see the side of your
vehicle in the mirror.
Be careful when judging the size or distance of any object seen
in the outside rear view mirror on the passenger’s side
because it is a convex mirror. Any object seen in a convex
mirror will look smaller and farther away than if seen in a normal
flat mirror.
When the inside rear view mirror darkens in “AUTO” mode, the
outside rear view mirrors also darken to reduce the reflection
of the headlights of the following vehicle. For details, see
“Inside rear view mirror” on page 196.
When you push the outside rear view mirror defogger switch,
the heater panels in the outside rear view mirrors will quickly
clear the mirror surface. (See “Outside rear view mirror
defogger switch” on page 38.)

Page 218 of 493

STEERING WHEEL AND MIRRORS
196
INSIDE REAR VIEW MIRROR
16X016e
Adjust the mirror so that you can just see the rear of your
vehicle in the mirror.
Pushing the switch changes the mode between “AUTO”
and “DAY”.
The indicator comes on when the “AUTO” mode is selected.
“DAY” mode: The mirror surface is normal.
“AUTO” mode: If the mirror detects light from the
headlights of the vehicle behind you, the mirror surface
darkens slightly to reduce the reflected light.
When the inside rear view mirror surface changes, the outside
rear view mirror surfaces will also become darker.
When the ignition key is inserted and turned on, the inside rear
view mirror always turns on in the “AUTO” mode. When
the inside air temperature is low, it may take a little longer
for the mirror to darken in response to the detection of
headlights.
CAUTION
Do not adjust the mirror while the vehicle is moving.
Doing so may cause the driver to mishandle the vehicle
and an accident may occur resulting in death or serious
injuries.
16x658b
To ensure correct functioning of antiglare mirror sensors
located on both sides of the mirror, do not touch or cover
the sensors with your finger or a piece of cloth, etc.

Page 280 of 493

STARTING AND DRIVING
258
PARKING BRAKE
31X065
1To set: Pull up the lever. For better holding power,
first depress the brake pedal and hold it while setting
the parking brake.
2 To release: Pull up the lever slightly (1), press the
lock release button (2), and lower the lever (3).
Before leaving your vehicle, firmly apply the parking brake. For
better holding power, first depress the brake pedal and hold it
while setting the parking brake.
CAUTION
Before driving, make sure the parking brake is fully
released and that the parking brake reminder light is off.
HOW TO START THE ENGINE
Cranking hold function
Once you turn the ignition key to “START” position and release
it, the cranking hold function continues to crank the engine in
“ON” position until it starts.
The function stops cranking the engine after about 25 seconds
maximum if the engine has not started yet. When you crank
the engine again, wait a few seconds and restart it.
If you hold the key in “START” position, the function will keep
cranking for about 30 seconds maximum.
Before cranking
1. Apply the parking brake firmly.
2. Turn off unnecessary lights and accessories.
3. Put the selector lever in “P”. If you need to restart the engine
while the vehicle is moving, put the selector lever in “N”. A
starter safety device will prevent the starter from operating if
the selector lever is in any drive position.
4. Depress the brake pedal and hold it to the floor until driving
off.

Page 288 of 493

STARTING AND DRIVING
266
(g) Driving in “2nd STRT” (second start)mode
31X012c
In the “2nd STRT” (second start) mode, the transmission
system shifts up from second gear. Use this mode when
starting your vehicle in sand, mud, ice or snow.
To set the “2nd STRT” mode, push the “2nd” switch. In the “2nd
STRT” mode, the “2nd STRT” indicator light comes on. To
cancel the “2nd STRT” mode, push the “2nd” switch again.
The “PWR” mode is automatically cancelled when you push
the “2nd” switch.
(h) If you cannot shift the selector lever
If you cannot shift the selector lever from “P” position even
though the brake pedal is depressed, use the shift lock
override button. For instruct ions, see “If you cannot shift
automatic transmission selector lever” on page 357.
FOURWHEEL DRIVE SYSTEM
(a) Fourwheel drive control
31X013e
Use the fourwheel drive control lever and center
differential lock button to select the fo llowing transfer and
center differential modes.
The “H” and “L” position of the four−wheel drive control lever
provides either lock or unlock mode of the center differential
depending on the center differential lock button position.
Use the center dif ferential lock system if your wheels get stuck
in a ditch, or when you are driving on a slippery or bumpy
surface. When the center differential is locked, the vehicle
stability control system is automatically turned off and the
center dif ferential lock and “VSC OFF” indicator lights come on
because the function that controls engine performance
interferes with the process of freeing your wheels.

Page 293 of 493

STARTING AND DRIVING
271
THE REAR VIEW MONITOR SYSTEM CAMERA
31x602b
The rear view monitor system camera is located on the back
door as shown in the illustration. The camera uses a special
lens. The distance of the image that appears on the screen
differs from the actual distance.
In the following cases, it may become difficult to see the images
on the screen, even when the system is functioning.

In the dark (for example, at night)
 When the temperature near the lens is extremely high or low
 When water droplets are adhering to the camera, or when
humidity is high (for example, when it rains)
 When foreign matter (for example, snow or mud) adheres
to the camera lens
 When the sun or the beam of headlights is shining directly
into the camera lens
31x603
Check surroundings for safety.
If a bright light (for example, sunlight reflected off the vehicle
body) is picked up by the camera, the smear effect* peculiar
to the camera may occur.
*: Smear effect — A phenomenon that occurs when a bright
light (for example, sunlight reflected off the vehicle body) is
picked up by the camera; when transmitted by the camera, the
light source appears to have a vertical streak above and below
it.

Page 294 of 493

STARTING AND DRIVING
272
LEXUS NIGHT VIEW SYSTEM
31X521
The Lexus night view system can help you see forward
when driving at night. If pedestrians or objects are
detected within the area reaching the tip of the low beam
to high beam, they are displayed along with the layout of
the road in the windshield as a monochrome image.
CAUTION
 This system should be used as a supplemental aid to
help you see objects. Never depend on this system
only. Be sure to view objects with your own eyes
while driving.
 This system is designed to help you see objects
better when driving in a flat area with few curves in
darkness. Use of this function in an area with many
curves or slopes or in a welllit area could cause an
accident.
Turning on the system
31x522b
The Lexus night view system turns on and the “MAIN”
indicator light comes on when you push the knob with the
ignition switch on:
When the system is turned on in the following conditions, the
head− up display (night view display) shutter opens
automatically and the image sent from the head −up display is
shown on the windshield.
 It is dark outside.
 The headlights are on.
When the vehicle starts moving in this condition, the “BEAM”
indicator light comes on, the near −infrared floodlight (night
view projector) is irradiated, and the image of the road ahead
is shown on the windshield.
You can adjust the brightness by turning the knob.

Page 295 of 493

STARTING AND DRIVING
273
While the
system is on, pushing the knob turns off the “MAIN”
indicator light and the system. If you turn the ignition off with
the system turned on, the system will be turned off
automatically.
CAUTION
If the image in the headup display (night view display)
is too bright, you cannot see the surroundings through
the windshield clearly. To avoid glare, do not make the
display brighter than necessary.
31x533c
 1 Nearinfrared floodlight (Night view projector)
2Nearinfrared camera (Night view camera)
3Headup display (Night view display)
4Automatic light control sensor
The nearinfrared floodlight (night view projector which
irradiates nearinfrared light not seen by people) located
near the fog lights irradiates the area reaching from the tip
of the low beam to high beam. The nearinfrared camera
(night view camera) located on top of the windshield
converts irradiated light into an image. This image is
shown on the headup display (night view display)
located on the bottom of the windshield.
The automatic light control sensor is on top of the passenger
side instrument panel.
Do not place anything on the instrument panel and do not affix
anything on the windshield to block this sensor.

Page 306 of 493

STARTING AND DRIVING
284
CAUTION
If you drive through deep water over about 500 mm (20
in.) in depth, put the vehicle height in the “HI” (High)
mode with the height select switch and then turn off the
active height control suspension by pushing the height
control switch. Drive your vehicle at 30 km/h (19 mph)
or lower speed.
NOTICE
 When jacking up or installing tire chains, be sure to
turn off the active height control suspension and
stop the engine. Otherwise, the vehicle height may
change because of the automatic leveling function,
resulting in an accident.
 If your vehicle must be towed, put the vehicle height
in the normal mode and turn off the active height
control suspension. Otherwise, the vehicle height
may change because of the automatic leveling
function, resulting in an accident.
 If your vehicle gets ditched, turn off the active height
control suspension with the height control switch.
Otherwise, the vehicle height may change because of
the automatic leveling function, resulting in an
accident.
Even after the active height control suspension is turned
off with the height control switch, if the vehicle speed
exceeds 30 km (19 mph), the active height control
automatically selects the normal mode.
(f) Height control indicator lights
31X050d
 1 Height control indicator lights
2Height control “OFF” indicator light
When the ignition switch is turned on, all the indicator
lights come on. The indicator light showing the present
mode only remains on and all other lights go off after a few
seconds. This means the system operates correctly.
If you change the vehicle height mode, the indicator lights
change as follows:

Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 60 next >