roof LEXUS LX470 2006 Owner's Manual
Page 219 of 493
STEERING WHEEL AND MIRRORS
197
Compass (vehicles without navigation
system)
16x271a
The compass indicates the direction in which the vehicle
is heading. The illustration shown above indicates that the
vehicle is heading north.Displays
Directions
N
NE
E
SE S
SW W
NWNorth
Northeast
East
Southeast South
Southwest West
Northwest
Pushing the “AUTO” button for longer than 3 seconds
turns on or off the compass display.
The compass may not show the correct direction in the
following conditions:
The vehicle is stopped immediately after turning.
The compass does not adjust while the vehicle is stopped.
The ignition switch is turned off immediately after turning.
The vehicle is on an inclined surface.
The vehicle is in a place where the earth’s magnetic field is
subject to interference by artificial magnetic fields
(underground parking, under a steel tower, between
buildings, roof parking, near a crossing, near a large
vehicle, etc.).
The vehicle is magnetized. (There is a magnet or a metal
object on or near the inside rear view mirror.)
The battery has been disconnected.
Any door is open.
If the deviation is small, the compass works to calibrate the
direction automatically while the vehicle in motion.
For obtaining additional precision or for complete calibrating,
see “CALIBRATING THE COMPASS” below.
Page 221 of 493
STEERING WHEEL AND MIRRORS
199
CAUTION
Do not adjust the display while the vehicle is moving.
Be sure to adjust the display only when the vehicle is
stopped.
CALIBRATING THE COMPASS (circling calibration)
16x280a
“C” appears on the display in case the circling calibration is
required due to a drastic change in the magnetic field. To
rectify this, follow the calibration procedure below.
16x270
Drive the vehicle slowly (at 8 km/h (5 mph) or lower) in a circle
until the direction is displayed. If there is not enough space to
drive in a circle, drive around the block until the direction is
displayed.
After driving in 1 to 3 circles in the above method, calibration
is complete with the direction shown on the display.
If calibration cannot be performed because of the magnetized
vehicle, etc., take your vehicle to Lexus dealer.
Do not perform circling calibration of the compass in a place
where the earth’s magnetic field is subject to interference by
artificial magnetic fields (underground parking, under a
steel tower, between buildings, roof parking, near a
crossing, near a large vehicle, etc.).
During calibration, do not operate electric systems (moon
roof, power windows, etc.) as they may interfere with the
calibration.
Page 235 of 493
AIR CONDITIONING
213
REAR AIR CONDITIONINGCONTROLS
20X054b
The control panel is located in the roof panel above the
second seat.
1 Automatic control button
2 Air flow control buttons
3 OFF button
4 Temperature control lever
5 Fan speed control buttons
The automatic air conditioning automatically maintains the set
temperature.
This air conditioning features automatic fan speed and air flow
control which automatically se lects the most suitable fan
speed and air flow to control the temperature. The ignition key
must be in the “ON” position.
NOTICE
To prevent the battery from being discharged, do not
leave the air conditioning on longer than necessary
when the engine is not running.
Page 237 of 493
AIR CONDITIONING
215
20X056
2. Use the temperature control lever to set the desired
temperature.
Slide the lever to the right for higher temperature and to the left
for lower temperature.
In the vehicles sold in U.S.A., the figures above the
temperature control lever are the temperature in degrees
Fahrenheit, while in the vehicles sold in Canada, the
temperature is indicated in degrees Centigrade. SETTING OPERATION manual control
If manual air flow selection is desired
20X057a
The outlets from which air is delivered can be selected
manually by
pressing in the appropriate air flow control button.
The function of each button is as follows:
1 Panel − Air flows mainly from the roof panel vents.
2
Bi level − Air flows from both the floor vents and the roof
panel vents.
3 Floor − Air flows mainly from the floor vents.
Air at higher than room temperature does not flow from the roof
panel vents.
Air at lower than room temperature does not flow from the floor
vents.
Page 250 of 493
AUDIO
228
Radio operation (XM satellite radio broadcast)
To listen to a satellite radio broadcast in your vehicle, an
additional genuine Lexus satellite receiver and antenna (or
equivalents) must be purchased and installed. A subscription
to the XM satellite radio service is also necessary.
(a) How to subscribe to an XM satellite radio
An XM satellite radio is a tuner designed exclusively to receive
broadcasts provided under a separate subscription.
Availability is limited to the 48 contiguous states.
How to subscribe:
You must enter into a separate service agreement with the XM
radio in order to receive satellite broadcast programming in the
vehicle. Additional activation and service subscription fees
apply that are not included in the purchase price of the vehicle
and optional digital satellite tuner. For complete information on
subscription rates and terms, or to subscribe to the XM radio,
visit XM on the web at www.xmradio.com
or call an XM’s
Listener Care at (800) 852 −9696. The XM radio is solely
responsible for the quality, availability and content of the
satellite radio services provided, which are subject to the terms
and conditions of the XM radio customer service agreement.
Customers should have their radio ID ready; the radio ID can
be found by tuning to “channel 000” on the radio. For details,
see “Displaying the radio ID” below.
All fees and programming are the responsibility of the XM
satellite radio and are subject to change. Satellite tuner technology notice:
Lexus satellite radio tuners are awarded Type Approval
Certificates from XM Satellite Radio Inc. as proof of
compatibility
with the services offered by the XM satellite radio.
(b) Displaying the radio ID
Each XM tuner is identified with a unique radio ID. You will
need the radio ID when activating XM service or when
reporting a problem.
If you select the “CH 000” using the “AUDIO −TUNE” knob, the
ID code of 8 alphanumeric characters appears. If you select
another channel, display of the ID code is canceled. The
channel (000) alternates the display between the radio ID and
the specific radio ID code.