wheel LEXUS LX470 2006 Owner's Guide

STEERING WHEEL AND MIRRORS
199
CAUTION
Do not adjust the display while the vehicle is moving.
Be sure to adjust the display only when the vehicle is
stopped.
CALIBRATING THE COMPASS (circling calibration)
16x280a
“C” appears on the display in case the circling calibration is
required due to a drastic change in the magnetic field. To
rectify this, follow the calibration procedure below.
16x270
Drive the vehicle slowly (at 8 km/h (5 mph) or lower) in a circle
until the direction is displayed. If there is not enough space to
drive in a circle, drive around the block until the direction is
displayed.
After driving in 1 to 3 circles in the above method, calibration
is complete with the direction shown on the display.
If calibration cannot be performed because of the magnetized
vehicle, etc., take your vehicle to Lexus dealer.
 Do not perform circling calibration of the compass in a place
where the earth’s magnetic field is subject to interference by
artificial magnetic fields (underground parking, under a
steel tower, between buildings, roof parking, near a
crossing, near a large vehicle, etc.).
 During calibration, do not operate electric systems (moon
roof, power windows, etc.) as they may interfere with the
calibration.

STEERING WHEEL AND MIRRORS
200
CAUTION
When doing the circling calibration, be sure to secure
a wide space, and watch out for people and vehicles
in the neighborhood. Do not violate any local traffic
rules while performing circling calibration.
 Do not adjust the display while the vehicle is moving.
Be sure to adjust the display only when the vehicle is
stopped.

AUDIO
243
(i) If the player malfunctions
If the player or another unit equipped with the player
malfunctions,
your audio system will display the following error
messages.
If “WAIT” appears on the display: It indicates that the inside
of the player unit may be too hot due to the very high ambient
temperature. Remove the CD from the player and allow the
player to cool down.
If “ERROR 1” appears on the display: It indicates that the
CD is dirty, damaged, or it was inserted upside down. Clean
the CD or insert it correctly.
If “ERROR 3” or “ERROR 4” appears on the display: It
indicates there is trouble inside the system. Eject the CD.
If the malfunction is not rectified: Take your vehicle to your
Lexus dealer.
Audio remote controls (steering switches)
21x570
The switches are installed on the left side of the steering wheel.
“MODE” switch: Use this switch to change the mode. If a tape
or CD is not inserted, the “TAPE” or “CD” mode is skipped.
When you push the switch with the audio system turned off, the
audio system turns on.
“
” switches: Use these switches to adjust the volume.
Push “+” to increase the volu me and “–” to decrease the
volume. The volume continues to increase or decrease while
the switch is being pressed.

SECTION 3 – 1
253
STARTING AND DRIVING
Starting and driving
Three−way catalytic converters254
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine exhaust caution 255
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before starting the engine 256
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition switch 256
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . .
Parking brake 258
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . .
How to start the engine 258
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic transmission 259
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Four−wheel drive system 266
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear view monitor system 269
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lexus night view system 272
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cruise control 275
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . .
Active height control suspension (AHC) 279
. . . . . . . . . . . . . . . . . . . . .
Adaptive variable suspension (AVS) 287
. . . . . . . . . . . . . . . . . . . . . . . .
Active traction control system 288
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vehicle stability control system 290
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Variable gear ratio steering system 293
. . . . . . . . . . . . . . . . . . . . . . . . .
Brake system 295
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . .
Brake pad wear limit indicators 299
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tire pressure warning system 299
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

STARTING AND DRIVING
256
BEFORE STARTING THE ENGINE
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle, head restraint height
and steering wheel angle.
3. Adjust the inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts.
Remember to check that the service reminder indicators
function when turning the key to “ON”, and check the fuel
gauge to see that you have sufficient fuel.
IGNITION SWITCH
31X002a
“START” Starter motor on. The key will return to the
“ON” position when released.
For starting tips, see page 258.
“ON” Engine on and all accessories on.
This is the normal driving position.
NOTICE
Do not leave the key in the “ON” position if the engine
is not running. The battery will discharge and the
electronic ignition system could be damaged.
“ACC” Accessories such as the radio operate, but the
engine is off.

STARTING AND DRIVING
257
If you leave the key in the “ACC” or “LOCK” position and open
the driver’s door, a buzzer will remind you to remove the key.
31X003a
“LOCK” Engine is off and the steering wheel is locked.
The ignition key can be removed only at this position.
To turn the key from “ACC” to the “LOCK” position, you must
put the transmission selector lever in the “P” position.
Once you remove the key, the engine immobilizer system is
automatically set. See “Engine immobilizer system” on page
11 .
When starting the engine, the key may seem stuck at the
“LOCK” position. To free it, first be sure the key is pushed all
the way in, and then rock the steering wheel slightly while
turning the key gently.
If, in an emergency, you must turn the engine off while the
vehicle is moving, turn the key only to “ACC”.
It is not a malfunction if the needles on all meters and gauges
move slightly when the key is turned to the “ACC”, “ON” or
“START” position.
Several hours after the engine is turned off, you may hear a
sound coming from underneath the luggage compartment for
several minutes. This is normal operation and does not
indicate a malfunction. (See page vii.)

STARTING AND DRIVING
266
(g) Driving in “2nd STRT” (second start)mode
31X012c
In the “2nd STRT” (second start) mode, the transmission
system shifts up from second gear. Use this mode when
starting your vehicle in sand, mud, ice or snow.
To set the “2nd STRT” mode, push the “2nd” switch. In the “2nd
STRT” mode, the “2nd STRT” indicator light comes on. To
cancel the “2nd STRT” mode, push the “2nd” switch again.
The “PWR” mode is automatically cancelled when you push
the “2nd” switch.
(h) If you cannot shift the selector lever
If you cannot shift the selector lever from “P” position even
though the brake pedal is depressed, use the shift lock
override button. For instruct ions, see “If you cannot shift
automatic transmission selector lever” on page 357.
FOURWHEEL DRIVE SYSTEM
(a) Fourwheel drive control
31X013e
Use the fourwheel drive control lever and center
differential lock button to select the fo llowing transfer and
center differential modes.
The “H” and “L” position of the four−wheel drive control lever
provides either lock or unlock mode of the center differential
depending on the center differential lock button position.
Use the center dif ferential lock system if your wheels get stuck
in a ditch, or when you are driving on a slippery or bumpy
surface. When the center differential is locked, the vehicle
stability control system is automatically turned off and the
center dif ferential lock and “VSC OFF” indicator lights come on
because the function that controls engine performance
interferes with the process of freeing your wheels.

STARTING AND DRIVING
267
NOTICE
As soon as the center differential lock switch is turned
on, the “VSC OFF” indicator light comes on. After the
wheels are out of the ditch or off the slippery or bumpy
surface, turn the center differential lock switch off.
Make sure the center differential lock indicator light and
vehicle stability control system off indicator light turn
off.
“H” (high speed position, center differential unlocked):
Lever at “H”, center differential lock button left out
Use this for normal driving on all types of roads, from dry
hard−surfaced roads to wet, icy or snow −covered roads. This
position gives greater economy, quietest ride, least wear and
better vehicle control.
“H” (high speed position, center differential locked):
Lever at “H”, center differential lock button pushed in
Use this for greater traction when you experience a loss of
power, such as wheel slipping, in the center dif ferential unlock
mode.
“N” (neutral position): Lever at “N”
No power is delivered to the wheels. The vehicle must be
stopped. “L” (low speed position, center differential unlocked):
Lever at “L”, center differential lock button left out
Use this for maximum power and traction. Use this for climbing
or descending steep hills, off
−road driving, and hard pulling in
sand or mud.
In this mode, the braking feeling that occurs when the wheels
are negotiating a sharp corner is further reduced than in the “L”
(low position, center differential locked) mode.
“L” (low speed position, center differential locked): Lever
at “L”, center differential lock button pushed in
Use this for maximum power and traction. Use this for hard
pulling in situations the vehicle cannot negotiate even in the “L”
(low speed position, center differential unlocked) mode. Also,
using this mode when driving down steep off −road inclines will
help contribute to increased vehicle stability.
The indicator light tells when the differential lock is engaged.
Note that the differential is not still locked as long as the
indicator light remains off.
When the operation is not completed, the indicator blinks. If
the indicator light does not go off when you push out the center
differential lock switch, drive straight ahead while accelerating
or decelerating, or drive in reverse.
The center differential lock system operation is not completed
within 5 seconds while the cruise control system is set, cancel
the cruise control system. To cancel the cruise control system,
see “Cruise control” on page 275.

STARTING AND DRIVING
268If the indicator light does not go off when you push out the
center differential lock button, drive straight ahead while
accelerating or decelerating, or drive in reverse.
See “(b) Shifting procedure” for further instructions.
Advice for driving on slippery roads in “L” (low speed
position) mode
If you shift the four
−wheel drive control lever to “L”, the
automatic transmission lever to “2” when you drive in steep
off −road areas, the output of the brake can be controlled
effectively by the active traction control system, which assists
the driver to control the driving power of 4 wheels.
Use the “L” position of the automatic transmission lever for
maximum power and traction when your wheels get stuck or
when you drive down a steep incline. In the following cases,
the out put of the brake can be controlled by the active traction
control system if the engine speed is under 3,000 rpm
(normally engine speed is under 3,000 rpm when the wheels
get unstuck).
 The four− wheel drive control lever in the “L” position and the
automatic transmission lever in the “L” position or the
automatic transmission lever in the “D”, “4”, “3” or “2” \
with
the transmission downshifting to the first gear
 The four− wheel drive control lever in the “L” position and the
automatic transmission lever in the “R” position
(As for the automatic transmission lever positions, see
“Automatic transmission” on page 259.)
(b) Shifting procedure
To shift between unlock and lock modes in “H”, push the
center differential lock button.
To shift between unlock and lock modes in “L”, push the
center differential lock button.
To shift between “H” and “L”, stop the vehicle, put the
transmission into “N” and move the four −wheel drive control
lever.
CAUTION
Never move the fourwheel drive control lever if wheels
are slipping. Stop the slipping or spinning before
shifting.
NOTICE
For normal driving on dry and hard surface roads,
unlock the center dif ferential. To prevent damage to the
center differential lock system, do not push the center
differential lock button when the vehicle is cornering or
when its wheels are spinning freely of f the ground. If the
indicator light does not go off when unlocking the
center differential, drive straight ahead while
accelerating or decelerating, or drive in reverse.

STARTING AND DRIVING
279
ACTIVE HEIGHT CONTROLSUSPENSION (AHC)
This active height control suspension controls the vehicle
height depending on the vehicle driving condition. Select
your desired height among the “HI” (high), “N” (normal)
and “LO” (low) modes with the height select switch.
31X600
(a) Vehicle height modes
 “HI” (high) mode
The vehicle height is about 40 mm (1.6 in.) higher at front
and about 50 mm (2.0 in.) higher at rear than the normal
mode height.
This mode is suitable when driving on bumpy roads and
through water.
This mode is available when the vehicle speed is under about
30 km/h (19 mph).
CAUTION
The “HI” (high) or “Extra high” mode should be used for
severe offroad driving condition only. Because the
vehicle’s center of gravity is higher in this setting, the
vehicle may become unstable when turning abruptly,
resulting in an accident.
When the four −wheel drive control lever is put at “L”, this mode
may change to the extra high mode automatically in
accordance with the driving condition.
When the vehicle exceeds the specified vehicle speed, the
vehicle height changes to the following:
With the fourwheel drive control lever at “H” and at the
vehicle speed of 30 km/h (19 mph) or over, the normal mode
is automatically selected.
With the fourwheel drive control lever at “L” and at the
vehicle speed of 50 km/h (30 mph) or over, the vehicle
height becomes automatically about 25 mm (1.0 in.) higher
than the normal mode height. If the vehicle speed is lowered
about 20 km/h (12 mph) or le ss after that, the high mode
automatically resumes.
Extra high mode
This mode is automatically selected from the high mode
with the fourwheel drive control lever placed in “L”
position depending on the vehicle driving condition.
If the vehicle becomes stuck, the vehicle height rises
automatically to the extra high mode (slightly higher or at about
70 mm (2.8 in.) higher than normal mode height).