LEXUS NX250 350 2023 Owners Manual

IndicatorLane displaySteering iconSituationNot illuminatedNot illuminatedNot illuminatedSystem disabled
WhiteGray
Not illuminatedLane lines are not detected by the
system
WhiteWhite
Not illuminatedLane lines are detected by the system
Orange
FlashingOrange
Flashing
Not illuminated
Lane departure alert function is op-
erating for the side which the lane
display is flashing
GreenGreenGreen
Lane departure prevention function
is operating for the side which the
lane display is illuminated
Orange
FlashingOrange
FlashingGreen
Lane departure alert function/lane
departure prevention function is op-
erating for the side which the lane
display is flashing
ChangingLDAsettings

WARNING

Frontcrosstrafficalert*
FCTA(Frontcrosstrafficalert)
When approaching an intersection, etc., at a low speed, vehicles approaching from
the left and right of the front of the vehicle can be detected and the driver informed
of these vehicles.
FCTAsystemcontrol

INFORMATION

Assistanceindetectingvehiclesbehindwhenchanginglanes
RelatedLinks
Customizable features(P. 701)
PurposeoftheBlindSpotMonitor
The Blind Spot Monitor is a system that uses rear side radar sensors installed onthe inner side of the rear bumper on the left and right side to assist the driver in
confirming safety when changing lanes.
WARNING

Systemcomponents
A
Center display
Turning the Blind Spot Monitor on/off.
B
Outside rear view mirror indicators
When a vehicle is detected in a blind spot of
the outside rear view mirrors or approach-
ing rapidly from behind into a blind spot,
the outside rear view mirror indicator on
the detected side will illuminate. If the turn
signal lever is operated toward the detectedside, the outside rear view mirror indicator
flashes.
INFORMATION

WARNINGRA sensor or its surrounding area is subject to a strong impact.
R If the surrounding area of a sensor is scratched or dented, or part of them has
become disconnected.

The range of each detection area is:A
Approximately 1.6 ft. (0.5 m) to 11.5 ft. (3.5 m) from either side of the vehicle*2
B
Approximately 3.3 ft. (1 m) forward of the rear bumper
C
Approximately 9.8 ft. (3 m) from the rear bumper
D
Approximately 9.8 ft. (3 m) to 197 ft. (60 m) from the rear bumper
*3
TurningtheBlindSpotMonitorsystemON/OFF
The Blind Spot Monitor system can be changed between ON and OFF on the
center display.
1 Select
.
2 Select [Driving assist@ .
3 Select [Blind spot monitor@ .
When the BSM function is disabled, the driving assist infomation indicator illumi-
nates.
Each time the engine switch is turned off then changed to ON, the Blind Spot
Monitor will be enabled automatically.
INFORMATION

RWhen the sensor is misaligned due to a strong impact to the sensor or its surround-
ing area
R When mud, snow, ice, a sticker, etc., is covering the sensor or surrounding area on
the rear bumper
R When driving on a road surface that is wet with standing water during bad weather,
such as heavy rain, snow, or fog
R When multiple vehicles are approaching with only a small gap between each
vehicle
R When the distance between your vehicle and a following vehicle is short
R When there is a significant difference in speed between your vehicle and the
vehicle that enters the detection area
R When the difference in speed between your vehicle and another vehicle is chang-
ing
R When a vehicle enters a detection area traveling at about the same speed as your
vehicle
R As your vehicle starts from a stop, a vehicle remains in the detection area
R When driving up and down consecutive steep inclines, such as hills, dips in the road,
etc.
R When driving on roads with sharp bends, consecutive curves, or uneven surfaces
R When vehicle lanes are wide, or when driving on the edge of a lane, and the vehicle
in an adjacent lane is far away from your vehicle
R When an accessory (such as a bicycle carrier) is installed to the rear of the vehicle
R When there is a significant difference in height between your vehicle and the
vehicle that enters the detection area
R Immediately after the Blind Spot Monitor is turned on