check engine light LEXUS RX330 2006 User Guide

STARTING AND DRIVING
443

Selecting the “N” mode
To change “HI” to “N” mode: Push the height select switch
on the “
” (lower) side once.
To change “LO” to “N” mode: Push the height select switch
on the “ ” (higher) side once.
The “N” indicator light blinks as the vehicle’s height changes.
When the vehicle’s height reaches the “N” mode, the indicator
light remains on.
Even if the engine stops while the vehicle’s height is being
lowered, the operation continues for up to one minute.
 Selecting the “LO” mode
To change “N” mode to “LO”: Push the height select switch
on the “
” (lower) side once.
To change “HI” mode to “LO”: Push the height select switch
on the “
” (lower) side twice.
The “LO” indicator light blinks as the vehicle’s height changes.
When the vehicle’s height reaches the “LO” mode, the indicator
light remains on.
Even if the engine stops while the vehicle’s height is being
lowered, the operation continues for up to one minute.
CAUTION
 Before you lower the vehicle’s height with the height
select switch, check under the vehicle to make sure
nothing that could damage the vehicle or no one who
could be injured is there and that the underbody of
the vehicle does not touch the ground.
 Do not select the “HI” mode when you load cargo on
the roof luggage carrier. Otherwise it may result in a
loss of control or vehicle rollover due to failure to
operate this vehicle correctly.
NOTICE
If the vehicle height is changed frequently, the
compressor may overheat, causing the vehicle
height adjustment operation to stop.
 After unloading, vehicle height rises slightly. Take
sufficient care where overhead space is restricted.
 Do not select “LO” mode when on bumpy roads. If
the underbody of the vehicle touches the rugged
road surface, the vehicle may be damaged.

STARTING AND DRIVING
445
1Higher2Lower
3Height control indicator lights
 Changing the mode
You can change the easy access mode to the “LO”, “N” or “HI”\
mode when the engine is running.
To change easy access mode to “LO” mode: Push the
height select switch on the “ ” (higher) side once.
To change easy access mode to “N”mode: Push the height
select switch on the “ ” (higher) side twice.
In the following cases, the vehicle’s height is automatically
changed to “N” (normal) mode.
 The vehicle speed exceeds approximately 12 km/h (8 mph).
 The engine is restarted and the easy access mode is
canceled. To change easy access
mode to “HI” mode: Push the height
select switch on the “ ” (higher) side for three times.
The “LO”, “N” or “HI” indicator light blinks while the\
vehicle’s
height changes. When the vehicle’s height reaches the “LO”,
“N” or “HI” mode, the indicator light remains on.
If the vehicle’s height is changed frequently, the raising or
lowering will take longer than usual. There is no problem in the
electronically modulated air suspension.
CAUTION
If you select easy access mode, check under the vehicle
to make sure nothing that could damage the vehicle or
no one who could be injured is there and that the
underbody of the vehicle does not touch the ground
before the engine is stopped.

STARTING AND DRIVING
446
(e) Turning off the electronically modulated airsuspension
1Height control switch
2Height control “OFF” indicator light
To turn off the electronically modulated air suspension
with the vehicle stopped, push the height control switch.
The height control “OFF” indicator light comes on and the
vehicle height is fixed in the same mode as was last
selected.
This status is maintained in the system even after the engine
is stopped.
If you push the switch again, the height control “OFF” indicator
light goes out and the electronically modulated air suspension
is turned on. When the vehicle’s speed exceeds 30 km/h (19 mph), the
height control “OFF” indicator light goes out and the
electronically modulated air suspension turns on
automatically.
CAUTION

If you drive through water, such as when crossing
shallow streams, first check the depth of the water
and the firmness of the bottom of the river bed then
put the vehicle height into “HI” mode with the height
select switch and turn off the electronically
modulated air suspension by pushing the height
control switch. Drive your vehicle at 30 km/h (19
mph) or slower and avoid deep water.
 When jacking up, installing tire chains or tying your
vehicle with chains or wires for transportation by a
flat bed, be sure to turn off the electronically
modulated air suspension with the height control
switch and stop the engine. Otherwise, the automatic
leveling function may cause the vehicle’s height to
change, resulting in an unexpected accident.
 If your vehicle must be towed, put the vehicle height
in the “N” mode and turn off the electronically
modulated air suspension. Otherwise, the automatic
leveling function may cause the vehicle’s height to
change, resulting in an unexpected accident.

STARTING AND DRIVING
448In the following cases, there is a problem somewhere in the
electronically
modulated air suspension, in which case the “N”
mode is automatically selected. Although there is no problem
to continue driving normally, have the electronically modulated
air suspension checked by your Lexus dealer as soon as
possible.
 The height control “OFF” indicator light does not come on
when the ignition switch is turned on.
 The height control “OFF” indicator light blinks.
(g) Operating noise of the electronically
modulated air suspension
You may hear an operating noise in the following cases. There
is no problem in the electronically modulated air suspension.
Selecting vehicle height with the height select switch
 Adjusting vehicle height according to the number of
occupants or the luggage load
 Changing vehicle height by selecting the easy access mode
when the engine is stopped
 Changing vehicle height by selecting the easy access mode
when the vehicle speed exceeds 12 km/h (8 mph)
 Changing the vehicle height by selecting the “HI” mode
when the vehicle speed exceeds 50 km/h (31 mph) or
driving at a speed of 30 km/h (19 mph) for 10 seconds or
more
 Lowering the vehicle’s height automatically when the
vehicle is moving at high speed
 Returning the vehicle height after high speed driving

STARTING AND DRIVING
450
Normal driving mode
Slip indicator light
Leave the system on during the ordinary driving so that it
can operate when needed.
You may hear a sound in the engine compartment for a few
seconds just after the vehicle begins to move. This means that
the traction control system is in the self− check mode, but does
not indicate a malfunction. When the traction control system is operating, the following
conditions occur:

The system controls the spinning of the front wheels. At this
time, the slip indicator light blinks.
 You may feel vibration or noise in your vehicle, caused by
operation of the brakes. This indicates the system is
functioning properly.
The slip indicator light comes on for a few seconds when the
ignition key is turned to “ON”. If the indicator light does not
come on when the ignition is turned on, contact your Lexus
dealer.

STARTING AND DRIVING
453
TRACTION CONTROL SYSTEM
(fourwheel drive modes)
The traction control system automatically helps prevent
the spinning of 4 wheels when the vehicle is started or
accelerated on slippery road surfaces.
When the ignition key is turned to “ON”, the system
automatically turns on.
CAUTION
Under certain slippery road conditions, full traction of
the vehicle and power against 4 wheels cannot be
maintained, even though the traction control system is
in operation. Do not drive the vehicle under any speed
or maneuvering conditions which may cause the
vehicle to lose traction control. In situations where the
road surface is covered with ice or snow, your vehicle
should be fitted with snow tires or tire chains. Always
drive at an appropriate and cautious speed for the
present road conditions.
Normal driving mode
 Slip indicator light
Leave the system on during the ordinary driving so that it
can operate when needed.
You may hear a sound in the engine compartment for a few
seconds just after the vehicle begins to move. This means that
the traction control system is in the self− check mode, but does
not indicate a malfunction.

STARTING AND DRIVING
455
In the following cases, contact your Lexus dealer:

The warning light does not come on after the ignition key is
turned to “ON”.
 The warning light remains on after the ignition key is turned
to “ON”.
 The warning light comes on while driving.
VEHICLE STABILITY CONTROL
SYSTEM
The vehicle stability control system helps provide
comprehensive control of the systems such as antilock
brake system, traction control, engine control, etc. This
system automatically controls the brakes and engine to
help prevent the vehicle from skidding when cornering on
a slippery road surface or operating steering wheel
abruptly.
This system activates when the vehicle speed is about more
than 15 km/h (9 mph).
You may hear a sound in the engine compartment for a few
seconds just after the vehicle begins to move. This means that
the system is in the self −check mode, but does not indicate a
malfunction.

STARTING AND DRIVING
462
Brake assist system
If you slam the brakes on such as in an emergency or
apply the brakes more firmly than usual such as when
descending the hill with the designated number of
occupants in the vehicle, the brake assist system
provides more powerful braking.
If you slam the brakes on or apply the brakes more firmly, more
powerful braking will be applied. At this time, you may hear a
sound in the engine compartment and feel the vibrations of the
brake pedal. This does not indicate a malfunction.
The brake assist system becomes operative after the vehicle
has accelerated to a speed in excess of approximately 10 km/h
(6 mph). It stops operating when the vehicle decelerates to a
speed below approximately 5 km/h (3 mph).
For an explanation of this system’s warning light, see “ABS
warning light” on page 81 or 460.
TIRE PRESSURE WARNING SYSTEM
The tire pressure warning system is designed to provide
warning when tire inflation pressure is critically low while
the vehicle is moving. The low tire pressure warning light
comes on to inform you that such low tire pressure may
hamper driving.
This system is not designed to operate when the vehicle is
stopped. Therefore, check the tire inflation pressure regularly.
The recommended cold tire inflation pressure, tire size and the
vehicle capacity weight are on the tire and loading information
label. (For instructions, see “Checking tire inflation pressure”
on page 570.)
Installed tires should be of the specified size. They should be
of the same size and construction. If tires other than the
specified size are used, or if tires of different sizes or
constructions are mixed, the tire pressure warning system will
not function properly.

DRIVING TIPS
471
CAUTION
Before driving off, make sure the parking brake is
fully released and that the parking brake reminder
light is off.
 Do not leave your vehicle unattended while the
engine is running.
 Do not rest your foot on the brake pedal while driving.
It can cause dangerous overheating, needless wear,
and poor fuel economy.
 To drive down a long or steep hill, reduce your speed
and downshift. Remember, if you ride the brakes
excessively, they may overheat and not work
properly. See page 392 or 403.
 Be careful when accelerating, upshifting,
downshifting or braking on a slippery surface. The
abrupt change in engine speed, such as sudden
acceleration or engine braking, could cause the
vehicle to skid or spin.
Do not drive in excess of the speed limit. Even if the
legal speed limit permits it, do not drive over 140 km/h
(85 mph) unless your vehicle has highspeed
capability tires. Driving over 140 km/h (85 mph) may
result in tire failure, loss of control and possible
injury. Be sure to consult a tire dealer to determine
whether the tires on your vehicle are highspeed
capability tires or not before driving at such speeds.
 Do not continue normal driving when the brakes are
wet. If they are wet, your vehicle will require a longer
stopping distance, and it may pull to one side when
the brakes are applied. Also, the parking brake will
not hold the vehicle securely.
 Vehicles with electronically modulated air
suspension: If you drive through water, such as when
crossing swallow streams, first check the depth of
the water and the bottom of the river bed of firmness,
put the vehicle height in the “HI” (high) mode with the
height select switch and then turn off the
electronically modulated air suspension by pushing
the height control switch. Drive your vehicle at 30
km/h (19 mph) or lower speed.

DRIVING TIPS
483
Trailer lights
 Socket for trailer lights
Your vehicle is equipped with a wire harness stored in the rear
end underbody. Models with tow hitch receiver are fitted with
a socket for trailer lights under the rear bumper. Use either of
them to connect and operate the trailer lights. However, the
trailer lights must comply with federal, state/provincial and
local regulations. See your local recreational vehicle dealer or
rental agency for the correct type of wiring and relays for your
trailer. Check for correct operation of the turn signals and stop
lights each time you hitch up. Direct splicing may damage your
vehicle’s electrical system and cause a malfunction of your
lights.
Breakin schedule
 Lexus recommends that you do not tow a trailer with a new
vehicle or a vehicle with any new power train component
(engine, transmission, differential, wheel bearing, etc.) for
the first 800 km (500 miles) of driving.
Maintenance
 If you tow a trailer, your vehicle will require more frequent
maintenance due to the additional load. For this
information, please refer to the scheduled maintenance
information in the “Owner’s Manual Supplement /
Scheduled Maintenance”.
 Retighten all fixing bolts of the towing ball and bracket after
approximately 1000 km (600 miles) of trailer driving.
Connecting a trailer (models with
electronically modulated air suspension)
Stop your vehicle and a trailer in line and perform the following:
1. Put the electronically modulated air suspension in the “LO”
mode. Turn the ignition switch off or push the height control
switch to turn off the electronically modulated air suspension.
2. Connect a trailer.
3. Turn the ignition switch on or push the height control switch
to turn on the electronically modulated air suspension. Select
the “N” (normal) mode with the height select switch.