warning light LEXUS RX330 2006 Owner's Guide

OCCUPANT RESTRAINT SYSTEMS
186
1Curtain shield airbag modules (airbag and inflater)
2Side airbag modules (airbag and inflator)
3Front passenger occupant classification system
(ECU and sensors)
4“AIRBAG ON” and “AIRBAG OFF” indicator lights
5SRS warning light
6Curtain shield airbag sensor assemblies
7Side and curtain shield airbag sensor assemblies
8Airbag sensor assembly
9Front passenger’s seat belt buckle switch
The SRS side airbag and curtain shield airbag system consists
mainly of the above components, and their locations are shown
in the illustration.
The SRS side airbag and curtain shield airbag system is
controlled by the airbag sensor assembly. The airbag sensor
assembly consists of a safing sensor and airbag sensor.
In a severe side impact, the side and curtain shield airbag
sensor and/or the curtain shield airbag sensor trigger(s) the
side airbag inflators and/or the curtain shield airbag inflators.
At this time a chemical reaction in the inflators quickly fills the
airbags with non −toxic gas to help restrain the lateral motion
of the occupants.
In a vehicle rollover, the airbag sensor assembly triggers the
curtain shield airbag inflator. At this time, a chemical reaction
in the inflators quickly fills the airbags with non −toxic gas to
help restrain the lateral motion of the occupants. When the airbags inflate, they produce a fairly loud noise and
release some smoke and residue along with non
−toxic gas.
This does not indicate a fire. This smoke may remain inside the
vehicle for some time, and may cause some minor irritation to
the eyes, skin or breathing. Be sure to wash off any residue as
soon as possible to prevent any potential skin irritation with
soap and water. If you can safely exit from the vehicle, you
should do so immediately.
Deployment of the airbags happens in a fraction of a second,
so the airbags must inflate with considerable force. While the
system is designed to reduce se rious injuries, it may also
cause minor burns or abrasions and swelling.
Front seats as well as parts of the front and rear pillars, and roof
side rail may be hot for several minutes, but the airbags
themselves will not be hot. The airbags are designed to inflate
only once.
CAUTION
SRS side airbags and curtain shield airbags inflate with
considerable force. To reduce the possibility of death
or serious injury when they inflate, the driver, front
passenger and rear outboard passengers must:
 Wear their seat belts properly.
 Remain properly seated with their backs upright and
against the seats at all times.

OCCUPANT RESTRAINT SYSTEMS
191
The indicator comes on when the ignition key is turned to
the “ON” position. It goes off after about 6 seconds. This
means the SRS side airbags and curtain shield airbags are
operating properly.
This warning light system monitors the airbag sensor
assembly, front airbag sensors, side and curtain shield airbag
sensor assemblies, curtain shield airbag sensor assemblies,
driver’s seat position sensor, driver’s seat belt buckle switch,
front passenger occupant classification system, “AIRBAG ON”
indicator light, “AIRBAG OFF” indicator light, front passenger’s
seat belt buckle switch, front seat belt pretensioner
assemblies, inflators, warning light, interconnecting wiring and
power sources. (For details, see “Service reminder indicators
and warning buzzers” on page 74 for instructions.)
If any of the following conditions occurs, this indicates a
malfunction of the airbags or seat belt pretensioners. Contact
your Lexus dealer as soon as possible. 
The light does not come on when the ignition key is turned
to the “ON” position or remains on for more than 6 seconds
or flashes.
 The light comes on or starts flashing while driving.
If the light stays on, it indicates that the SRS driver and front
passenger airbag and/or front passenger occupant
classification system, ”AIRBAG ON” indicator light and
“AIRBAG OFF” indicator light have a problem. If the light
flashes, the SRS side and curtain shield airbags have a
problem.
The SRS warning light and “AIRBAG OFF” indicator light will
be illuminated if there is a malfunction in the front passenger
occupant classification system.

OCCUPANT RESTRAINT SYSTEMS
193
FRONT PASSENGER OCCUPANTCLASSIFICATION SYSTEM
Your vehicle is equipped with a front passenger occupant
classification system. This system detects the conditions
1 — 4 in the table shown below, and based on these
conditions activates or deactivates the following
systems;
 Front passenger airbag
 Side airbag on the front passenger seat
 Front passenger’s seat belt pretensioner
The system monitors the weight and load on the front
passenger seat, and the seat belt buckle switch in
determining conditions 1 — 4.
In order for the system to detect the conditions correctly,
do not do any of the following:
 Apply a heavy load to the front passenger seat or equipment
(e.g. seatback pocket or armrest).
 Attach a commercial seatback table, etc. to the front
passenger seat seatback.
 Put weight on the front passenger seat by putting your
hands or feet on the seatback from the rear passenger seat.
“AIRBAG ON” and “AIRBAG OFF” indicator and front
passenger’s seat belt reminder light
SRS warning light

OCCUPANT RESTRAINT SYSTEMS
194The “AIRBAG ON” and “AIRBAG OFF” indicator lights will
be illuminated when the ignition switch is in the “ON”
position
and a child or child restraint system is in the front
passenger seat (see tablecondition 2). This indicates
that in the event of a severe frontal or passenger’s side
impact, the front passenger airbag and side airbag on the
front passenger seat are deactivated and will not deploy.
If the front passenger occupant classification system
determines that a person of adult size sits in the front
passenger seat but the “AIRBAG OFF” indicator light is
illuminated, one of the following is likely to have occurred:
 The rear passenger lifts the front passenger seat cushion
with their legs.
 Objects are placed under the front passenger seat.
 A front passenger seat seatback is in contact with a rear
seat.
To ensure the system correctly detects an adult sitting in the
front passenger seat, make sure the above do not happen.
Make sure the “AIRBAG ON” indicator light is illuminated when
an adult sits in the front passenger seat. If the “AIRBAG OFF”
indicator light is illuminated, ask the passenger to sit up
straight, well back in the seat, and with the seat belt worn
correctly. If the “AIRBAG OFF” indicator light still remains
illuminated, either ask the passenger to move to the rear seat,
or if that is not possible, move the front passenger seat fully
rearward. The “AIRBAG ON” and “AIRBAG OFF” indicator light will
be initially illuminated when the ignition switch is turned
to the “ON” position. It will remain for about four seconds
and then go off. After about two seconds, the front
passenger occupant classification system operates and
judges whether to turn the indicator light on or not.
The SRS warning light and “AIRBAG OFF” indicator light
will be illuminated if there is a malfunction in the front
passenger occupant classification system.

OCCUPANT RESTRAINT SYSTEMS
195
Condition and operation in the front passenger occupant classification s\
ystem
Condition detected by the front
passenger occupant
classification system
Indicator/warning lightDevices
“AIRBAG ON” and
“AIRBAG OFF”
indicator lights
SRS
warning light
Front
passenger’s seat belt
reminder light
Front
passenger airbagSide airbag
on the frontpassenger seatCurtain
shield airbag in the frontpassenger sideFront
passenger’s seat belt
pretensioner
1Adult*1“AIRBAG ON”OffFlashing*4Activated
2Child *2 or child
restraint system*3“AIRBAG OFF”OffFlashing*4Deactivated
Activated
Activated
3UnoccupiedNot
illuminatedOffOffDeactivatedDeactivated
4There is a
malfunction in the
system“AIRBAG OFF”OnOffDeactivatedActivated
*1: The system judges a person of adult size as an adult. When a smaller ad\
ult sits in the front passenger seat, the system may recognize him/her as a child depending on his/her physique and posture.
*
2: When a larger child who has outgrown a child restraint system sits in the front\
passenger seat, the system may recognize him/her as an adult depending on his/her physique or posture.
*
3: Never install a rear −facing child restraint system on the front passenger seat. A forward −facing child restraint system should
only be installed on the front passenger seat when it is unavoidable. (\
See “Child restraint system” as for installing the chil d
restraint system.)
*
4: In the event the front passenger does not wear a seat belt.

OCCUPANT RESTRAINT SYSTEMS
197
If an adult sits in the front passenger seat, the
“AIRBAG ON” indicator light is illuminated. If the
“AIRBAG OFF” indicator is illuminated, ask the
passenger to sit up straight, well back in the seat, feet
on the floor, and with the seat belt worn correctly. If
the “AIRBAG OFF” indicator still remain illuminated,
either ask the passenger to move to the rear seat, or
if that is not possible, move the front passenger seat
fully rearward.
 When it is unavoidable to install the forwardfacing
child restraint system on the front passenger seat,
install the child restraint system on the front
passenger seat in the proper order. (As for the
installation order, see “Child restraint system” on
page 199.)
 Do not remove the seat.
 Do not kick the front passenger seat or subject it to
severe impact. Otherwise, the SRS warning light may
come on to indicate a malfunction of the detection
system. In this case, contact your Lexus dealer
immediately.
 Child restraint systems installed on the rear seat
should not contact the front seatbacks.In addition to the precautions outlined above, the “AIRBAG
ON” indicator light may be illuminated when a child sits in the
front passenger seat or a forward −facing child restraint system
is installed in the front passenger seat. If the “AIRBAG ON”
indicator light is illuminated in these circumstances, the front
passenger airbag and side airbag on the front passenger side
are in an activated condition — the airbags will deploy if an
impact meets the deployment criteria. Refer to all the cautions
in this Section and “Child restraint system” on page 199.

STARTING AND DRIVING
402“3” (third range): The most suitable gear is automatically
selected between first and third gears according to vehicle
speed and driving conditions. This range is best used when
stronger engine braking is necessary.
“2” (second range): First or second gear will automatically
be selected according to vehicle speed and driving
conditions. This range is to be used when engine braking
stronger than that of the “3” (third range) position is
necessary.
“1” (first range): This gear is fixed in first regardless of
vehicle
speed or driving conditions. This range is to be used
when maximum engine braking is necessary.
If you attempt to downshift the transmission when it is not
possible to downshift due to high vehicle speed, a warning tone
sounds twice. 
Maximum allowable speeds
To get on a highway or to pass slower traffic, maximum
acceleration may be necessary. Make sure you observe the
following maximum allowable speeds in each range:
range km/h (mph)1 51 (32)
2 92 (58)
3 144 (90)
NOTICE
Do not downshift if you are going faster than the
maximum allowable speed for the next lower range.
 “S” mode indicator light
“S” mode allows you to use the shift range positions.
The “S” mode indicator light comes on when the selector
lever is shifted into the “S” position. When the “S” mode
indicator light does not come on even with the selector lever
moved to the “S” position, there may be a problem
somewhere in the system. Have your vehicle
checked/repaired by your Lexus dealer as soon as possible.
In this case, you can drive in the same condition as in the “D”
position.

STARTING AND DRIVING
415
5Resetting to a slower speed
Press the control lever downward in the “ − SET” direction and
hold it. Release the lever when the desired speed is attained.
While the lever is held downward, the vehicle speed will
gradually decrease.
When the difference between the actual vehicle speed and the
set speed is less than 5 km/h (3 mph), the set speed can be
lowered 1.6 km/h (1 mph) each time by pressing the control
lever downward in the “ − SET” direction quickly.
However, a quicker way to reset is to depress the brake pedal
and then press the control lever downward in the “ − SET”
direction.
Vehicle with automatic transmission (standard type) —
Even if you downshift the transmission from the “D” position to
“4” with the cruise control on, engine braking will not be
enabled because the cruise control is not cancelled. To
decrease the vehicle speed, reset to a slower speed with the
cruise control lever or depress the brake pedal. If you use the
brake pedal, cruise control is cancelled.
Vehicle with automatic transmission (multi −mode type) —
Even if you downshift the transmission from the “D” or “5” (fifth
range) to the “4” (fourth range) with the cruise control on,
engine braking will not be enabled because the cruise control
is not cancelled. To decrease the vehicle speed, reset to a
slower speed with the cruise control lever or depress the brake
pedal. If you use the brake pedal, cruise control is cancelled.Cruise control failure warning
If the “CRUISE” indicator light flashes when using the cruise
control, press the “ON− OFF” button to turn the system off and
then press it again to turn it on.
If any of the following conditions then occurs, there is some
trouble in the cruise control system.
 The indicator light does not come on.
 The indicator light flashes again.
 The indicator light goes out after it comes on.
If this is the case, contact your Lexus dealer and have your
Lexus inspected.

STARTING AND DRIVING
416
DYNAMIC LASER CRUISECONTROL
Dynamic laser cruise control allows you to drive at a
constant cruising speeds over about 45 km/h (28 mph)
with your foot off the accelerator pedal, maintaining an
appropriate vehicletovehicle distance between the
vehicle ahead.
CAUTION
Do not rely excessively on dynamic laser cruise control
in order to avoid serious injury or death, or to prevent
accidents or to control the vehicle’s speed in
emergency situations. Do not use cruise control except
in appropriate road and traffic conditions. Always drive
carefully and attentively. Before using dynamic laser
cruise control, read and understand the following
instructions.1Cruise control switch
2Distance switch
3Display
4“NORM.” indicator light
(conventional cruise control mode indicator light)
5“CRUISE” indicator light
6“READY” indicator light
(ready mode indicator light)
7Master warning light

STARTING AND DRIVING
425
Bring your vehicle to the desired speed, push the lever down
in the “−
SET” direction and release it. This sets the vehicle at
that speed. At this time, the display indicates settings such as
the preset vehicle speed, whether a vehicle is present ahead
and the selected following distance. If no vehicle is detected
ahead, the display does not indicate the vehicle ahead. You
can now take your foot off the accelerator pedal.
If you need to accelerate — for example, when passing —
depress the accelerator pedal enough for the vehicle to exceed
the preset speed. When you release the accelerator pedal, the
vehicle will return to the control prior to acceleration.
You cannot set a desired speed if the master warning light
comes on, the alarm sounds and the display indicates one of
the warning codes “E1”, “E2” or “E3”. If any of the above codes
appears on the display, see “(l) Vehicle −to−vehicle distance
control mode failure warning” on page 431. (d) Cancelling the vehicletovehicle distance control
mode
The vehicle
−to−vehicle distance control mode may be
temporarily cancelled by the driver or by the system itself under
certain circumstances. Temporary cancellation allows the set
cruising speed and vehicle −to−vehicle distance to remain in
memory.
The vehicle −to−vehicle distance control mode can be
temporarily cancelled by doing the following:
 Pulling the lever in the “CANCEL” direction and releasing it
 Depressing the brake pedal
Under certain circumstances, the vehicle −to− vehicle distance
control mode is temporarily cancelled:
 When vehicle speed falls below 40 km/h (25 mph)
 When vehicle stability control is activated
The “READY” indicator light comes on to indicate that the
system is still in operation.
To turn the system off, press the “ON −OFF” button. Make sure
the “CRUISE” indicator light is off.
If one of the warning codes “E1”, “E2” or “E3” appears\
on the
display, the preset speed automatically cancels out. See “(l)
Vehicle −to−vehicle distance control mode failure warning” on
page 431.
If the vehicle− to−vehicle distance control mode automatically
cancels out other than for the above cases, have your vehicle
checked by your Lexus dealer at the earliest opportunity.