engine LEXUS RX350 2015 Owners Manual

4253-3. Using the Lexus Display Audio system
3
Interior features ■
Certification for the Bluetooth ®
audio system
FCC ID: AJDK046
IC ID: 775E-K046
This device complies with Part 15 of FCC Rules and Indust ry Canada licence-
exempt RSS standard(s). Operation is subj ect to the following two conditions: (1)
this device may not cause interference, an d (2) this device must accept any inter-
ference, including interference that may cause undesired operation of this device.
Le présent appareil est conforme aux la partie 15 des règles de la FCC et CNR
d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploita-
tion est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire
de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouilla ge est susceptible d’en compromettre le
fonctionnement.■
Reconnecting the portable audio player
If the portable audio player is disconnected with a poor reception when the
“ENGINE START STOP” switch is in AC CESSORY or IGNITION ON mode, the
system automatically reconnects the portable audio player.
If you have switched off the portable audio player yourself, follow the instructions
below to reconnect: ●
Select the portable audio player again●
Enter the portable audio player■
When you release your car
Be sure to initialize your data. (  P. 3 3 6 )

4453-3. Using the Lexus Display Audio system
3
Interior features Connecting a Bluetooth ®
phone
There are two connecting methods av ailable-automatic and manual.
Automatic
When you register your phone, auto connection will be activated. Always
set it to this mode and leave the Bluetooth ®
phone in a place where con-
nection can be established.
When the “ENGINE START STOP” sw itch is turned to ACCESSORY or
IGNITION ON mode, the system will se arch for a nearby mobile phone
you have registered.
The system automatically connects with the most recent phone that was
connected. The connected result is displayed.
Depending on the type of phone, phone operations may be required (to
confirm if connection is to be receiv ed or not) even when automatically
connected.

4463-3. Using the Lexus Display Audio system
Manual
When the auto connection has failed or “Bluetooth
* Power” is turned off
(  P. 478), you must connect Bluetooth ®
manually.
* : Bluetooth is a registered tr ademark of Bluetooth SIG. Inc.
Display the “Phone” screen .
(  P. 4 4 1 )
Select “Connect Phone”.
Select the device to connect. A message is shown if connection
has been successful.
If connection fails, a message will
be displayed and connection will
be re-attempted.STEP 1
STEP 2
STEP 3
■
Reconnecting to the Bluetooth ®
phone
If the system cannot connect due to poor signal strength with the “ENGINE START
STOP” switch in ACCESSORY or IGNITION ON mode, the system will automat-
ically attempt to reconnect.
If the phone is turned off, the system will not attempt to reconnect. In this case, con-
nection must be made manually, or the phone must be re-selected.
■
Connecting the phone while Bluetooth ®
audio is playing
●
Bluetooth ®
audio will stop temporarily.
●
It may take time to connect.

4653-3. Using the Lexus Display Audio system
3
Interior features ■
Phonebook data
Phonebook data is managed for every registered phone. When another phone is
connecting, you cannot read the registered data.■
Setting the phonebook in a different wa y (To display the “Contacts” screen)
Display the “Phone” screen. (  P. 441)
Select “Contacts” on the “Phone” screen.
Select “Options” on the “Contacts” screen.
Select “Manage Contacts” on the “Contacts” screen.■
When transferring a phone number
Transfer the phone number while engine is running.
If your mobile phone is OPP or PBAP co mpatible, you may need to input “1234” by
your mobile phone for OBEX certification.■
When you have selected “Update Cont acts” to transfer the phone number●
If your mobile phone does not support PBAP service, you cannot use this func-
tion.●
If your phone supports PBAP service, you can transfer the phonebook data
without operating your phone.■
When you have selected “Replace Contacts” or “Add Contacts” to transfer the
phone number
If your mobile phone does not support OPP service, you cannot use these func-
tions. You can transfer the phonebook data only by operating your phone.■
Transferring the phone number in a different way (To display the “Transfer
Contacts” screen)
Display the “Phone” screen. (  P. 441)
Select “Contacts” on the “Phone” screen.
Select “Transfer” on the “Contacts” screen.
■
Transferring the phone number while Bluetooth 
audio is playing
Bluetooth 
audio will disconnect. It will reconnect automatically when data transfer
finishes. It will not be reconnected depending on the phone you are using. STEP 1
STEP 2
STEP 3
STEP 4
STEP 1
STEP 2
STEP 3

4823-4. Using the audio system
■
Using mobile phones
Interference may be heard through the audio system’s speakers if a mobile phone is
being used inside or close to the vehi cle while the audio system is operating.
CAUTION■
Certification ●
Pa r t 1 5 o f t h e F CC Ru l e s
FCC Warning:
Any unauthorized changes or modifications to this equipment will void the user’s
authority to operate this device.●
This product is a class 1 laser product clas sified under the Safety of laser products,
IEC 60825-1:2007, and contains a class 1 M laser module. To ensure continued
safety, do not remove any covers or atte mpt to gain access to the inside of the
product. Refer all servicing to qualified personnel.
NOTICE■
To prevent battery discharge
Do not leave the audio system on longer than necessary when the engine is off.
■
To avoid damaging the audio system
Take care not to spill drinks or other fluids over the audio system.CLASS 1 LASER PRODUCT
CAUTION - CLASS 1 M INVISIBLE LASER
RADIATION WHEN OPEN, DO NOT
VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS.

5473-4. Using the audio system
3
Interior features Pattern A
Press the talk switch and say “From Car” or “From Audio player”,
and select “Confirm” by using a voice command or .
Pattern B
Select “From Car” or “From Audio”, using . If “From Car” is selected, the portable player will be automatically con-
nected whenever the “ENGINE START STOP” switch is in either
ACCESSORY or IGNITION ON mode.
Changing the registered name of a portable player
Select “Change Name” using a voice command or .
Pattern A
Select the name of the portable player to be changed by either of
the following methods, and sele ct “Confirm” using a voice com-
mand or :
a. Press the talk switch and say the name of the desired portable
player.
b. Press the talk switch and sa y “List Audio Players”. When the
name of the desired portable pl ayer is read aloud, press the
talk switch.STEP 3
STEP 3
STEP 1
STEP 2

5973-5. Using the interior lights
3
Interior features ■
Illuminated entry system
The lights automatically turn on/off according to “ENGINE START STOP” switch
mode, the presence of the electronic key, whether the doors are locked/unlocked,
and whether the doors are open/closed.■
To prevent battery discharge
When the “ENGINE START STOP” switch is turned off, the lights will go off auto-
matically after 20 minutes. ●
Personal lights●
Interior lights●
Door courtesy lights●
Scuff lights (if equipped)●
Footwell lights■
Customization
Settings (e.g. the time elapsed before the lights turn off) can be changed.
(Customizable features  P. 8 3 4 ) Interior lights and personal lights

6103-7. Other interior features
Vanity mirrors ■
To prevent battery discharge
When the “ENGINE START STOP” switch is turned off, the lights will go off auto-
matically after 20 minutes.
NOTICE■
When not in use
Keep the vanity mirror closed. Slide the cover to open. The light turns on when the
cover is opened.

6123-7. Other interior features
■
The clock is displayed when
The clock is displayed when the “ENGINE START STOP” switch is in ACCES-
SORY or IGNITION ON mode.■
When the battery is disconnected
The time display will automatically be set to 1:00.

6173-7. Other interior features
3
Interior features
■
The power outlets can be used when
12 V
The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode.
120 VAC
The “ENGINE START STOP” switch is in IGNITION ON mode. Luggage compartment (12V)
Open the cover.
On the back surface of the console (120 VAC)*
Open the cover.
*: If equipped