parking brake LEXUS SC300 1991 Service Owner's Manual

4. REMOVE SHOE RETURN SPRINGSUsing needle±nose pliers, remove the 2 shoe return springs.
5. REMOVE SHOE STRUT WITH SPRING
6. REMOVE FRONT SHOE ADJUSTER AND TENSION SPRING
(a) Slide out the front shoe and remove the shoe adjuster.
(b) Disconnect the tension spring and remove the front shoe.
7. REMOVE REAR SHOE
(a) Slide out the rear shoe.
(b) Remove the tension spring from the rear shoe.
(c) Disconnect the parking brake cable from the parking brake
shoe lever.
(d) Remove the shoe hold±down spring cups, springs and pins.
±
BRAKE SYSTEM REAR BRAKE (Parking Brake)BR±45
WhereEverybodyKnowsYourName

PARKING BRAKE COMPONENTS
INSPECTION AND REPAIR
BR04G±0B
1. INSPECT DISASSEMBLED PARTSInspect the disassembled parts for wear, rust or damage.
2. MEASURE BRAKE SHOE LINING THICKNESS Using a scale, measure the thickness of the shoe lining.
Standard thickness:
2.5 mm (0.098 in.)
Minimum thickness: 1.0 mm (0.039 in.)
If the lining thickness is at the minimum thickness or less, or
if there is extremely uneven wear, replace the brake shoe.
3. MEASURE BRAKE DISC INSIDE DIAMETER Using a vernier caliper, measure the inside diameter of the
disc.
Standard inside diameter:
190 mm (7.48 in.)
Maximum inside diameter: 191 mm (7.52 in.)
Replace the disc if the inside di ameter is at the maximum val-
ue or more. Replace the disc or grind it with a lathe if the disc
is scored or is worn unevenly.
4. INSPECT P ARKING BRAKE LINING AND DISC FOR
PROPER CONTACT
Apply chalk to the inside surface of the disc, then grind down
the brake shoe lining to fit. If the contact between the disc and
the brake shoe lining is improper, repair it using a brake shoe
grinder or replace the brake shoe assembly.
5. MEASURE CLEARANCE BETWEEN PARKING BRAKE SHOE AND LEVER
Using a feeler gauge, measure the clearance.
Standard clearance:
Less than 0.35 mm (0.0138 in.)
If the clearance is not within the specification, replace the
shim with one of the correct size.
BR±46
±
BRAKE SYSTEM REAR BRAKE (Parking Brake)
WhereEverybodyKnowsYourName

 
Thickness mm(in.) Thickness mm(in.)
 0.3 (0.012) 0.9 (0.035)
 

0.6 

(0.024) 


 


6. IF NECESSARY, REPLACE SHIM
(a) Remove the parking brake shoe lever, and install the correct
size shim.
(b) Install the parking brake shoe lever with a new Cwasher.
(c) Remeasure the clearance.
PARKING BRAKE ASSEMBLY
BR0ES±04
HINT: Assemble the parts in the correct direction, as shown.
1. APPLY HIGH TEMPERATURE GREASE ON BACK± ING PLATE
±
BRAKE SYSTEM REAR BRAKE (Parking Brake)BR±47
WhereEverybodyKnowsYourName

2. APPLY HIGH TEMPERATURE GREASE TO ADJUSTER
3. CONNECT PARKING BRAKE CABLE TO PARKINGBRAKE LEVER
(a) Install the shoe hold±down springs, cups and pins.
(b) Connect the parking brake cable to the parking brake shoe
lever of the rear shoe.
4. INSTALL REAR SHOE Slide in the rear shoe between the shoe hold±down spring
cup and the backing plate.
NOTICE: Do not allow oil or grease to get on the rubbing face.
5. INSTALL TENSION SPRING, FRONT SHOE ANDADJUSTER
(a) Install the tension spring on the rear shoe.
(b) Install the front shoe on the tension spring.
(c) Install the adjuster between the front and rear shoes.
(d) Slide in the front shoe between the shoe hold±down spring
cup and the backing plate.
BR±48
±
BRAKE SYSTEM REAR BRAKE (Parking Brake)
WhereEverybodyKnowsYourName

6. INSTALL SHOE STRUT WITH SPRINGInstall the strut with the spring forward.
7. INSTALL SHOE RETURN SPRINGS Using needle±nose pliers, install the front shoe return spring
and then install the rear shoe return spring.
8. INSTALL DISC
(a) Before installing, polish the disc and shoe surfaces with sandpaper.
(b) Align the matchmarks and install the disc. HINT: If there are no matchmarks, temporarily install the disc,
then measure the disc runout and install the disc in the posi-
tion.
(See page BR±41)
9. ADJUST PARKING BRAKE SHOE CLEARANCE
(a) Temporarily install the hub nuts.
(b) Remove the hole plug.
(c) Turn the adjuster and expand the shoes until the disc locks.
(d) Return the adjuster 8 notches.
(e) Install the hole plug.
10. INSTALL REAR DISC BRAKE ASSEMBLY Install the disc brake assembly and torque the 2 mounting
bolts.
Torque: 104 N Vm (1,065 kgf Vcm, 77 ft Vlbf)
11. INSTALL REAR WHEEL
±
BRAKE SYSTEM REAR BRAKE (Parking Brake)BR±49
WhereEverybodyKnowsYourName

12. SETTLING PARKING BRAKE SHOES AND DISC
(a) Drive the vehicle at about 50 km/h (31 mph) on a safe, leveland dry road.
(b) With the parking brake release button pushed in, pull on the
lever with 88 N (9 kgf, 19.8 lbf) of force.
(c) Drive the vehicle for about 400 meters (0.25 mile) in this condition.
(d) Repeat this procedure 2 or 3 times.
13. CHECK AND ADJUST PARKING BRAKE LEVER TRAVEL
BR±50
±
BRAKE SYSTEM REAR BRAKE (Parking Brake)
WhereEverybodyKnowsYourName

SERVICE SPECIFICATIONS
SERVICE DATA
MA002±0B 








Engine 








Spark plug
Recommended spark plug
Correct electrode gap
Firing order
Valve clearance 








ND
NGK
Intake
Exhaust
\








\
PK20R11
BKR6EP11
1.1 mm (0.043 in.)
1 ± 8 ± 4 ± 3 ± 6 ± 5 ± 7 ± 2
0.15 ± 0.25 mm (0.006 ± 0.010 in.)
0.25 ± 0.35 mm (0.010 ± 0.014 in.)
 






BrakeFront and rear brakes
Pad thickness
Disc thickness
Limit
Limit (Front) (Rear)1.0 mm (0.039 in.)
30.0 mm (1.181 in.)
15.0 mm (0.591 in.)
 




Disc runout
Parking brake
Lining thickness
Drum inside diameter
()
Limit
Limit
Limit
()
0.05 mm (0.0020 in.)
1.0 mm (0.039 in.)
191 mm (7.520 in.)
 ChassisSteering linkage
Steering wheel freeplay
Limit30 mm (1.18 in.) 


gy
Ball joint
Vertical play
Limit
()
0.3 mm (0.012 in.)
MA002±0B
TORQUE SPECIFICATIONS
\
 \
Part tightened N
Vm kgf Vcm ft Vlbf
 Spark plug x Cylinder head1818013
 Front seat x Body3737527
 Front suspension crossmember x Body for nut1271,30094
  for bolt 201
,
2,050148
 Rear suspension member x Body1761,800130
 Rear suspension member rear cushion x Body3839028
±
MAINTENANCE (1UZ ± FE)MA±21
WhereEverybodyKnowsYourName

V04535
(4) Also applicable to drum lining for parking brake. For other usage condit\
ions, refer to SCHEDULE B.
(5) Check for leakage.
(6) Check for oil leaks from steering gear housing.
(7) Applicable only when operating mainly on rough, muddy roads. The applicable parts \
are listed below. Forother usage conditions, refer to SCHEDULE B.
Front and rear suspension member to cross body.
 Bolts for seat installation.
±
MAINTENANCE (1UZ ± FE)MA±3
WhereEverybodyKnowsYourName

MA033±0C
SCHEDULE B
CONDITIONS:
Conditions others than those listed for SCHEDULE A.Maintenance operation: A = Check and adjust if necessary. R = Replace, change or lubricate.
I = Inspect and correct or replace if necessary.
V04409

mark indicates maintenance which is part of the warranty conditions for\
the Emission Control Systems.
The warranty period is in accordance with the owner's guide or the warranty booklet.
(
: California and New York specification vehicles only)
(1) Includes inspection of fuel tank band and vaper vent system.
(2) Also applicable to drum lining for parking brake.
(3) Check for leakage.
(4) Check for oil leaks from steering gear housing.
(5) The applicable parts are listed below. Front and rear suspension member to cross body.
 Bolts for seat installation.
MA±4
±
MAINTENANCE (1UZ ± FE)
WhereEverybodyKnowsYourName

14. INSPECT BRAKE PADS AND DISCS FOR FRONT ANDREAR
(a) Check the thickness of the disc brake pads and check for irregular wear.
Minimum pad thickness:
1.0 mm (0.039 in.)
HINT: If a squealing or scraping noise comes from the brake
during driving, check the pad wear indicator to see if it is con-
tacting the disc rotor. If so, the disc pad should be replaced.
(b) Check the disc for wear or runout.
Minimum disc thickness: Front
30.0 mm (1.181 in.)
Rear
15.0 mm (0.591 in.)
(c) Check the disc for runout.
Maximum disc runout: 0.05 mm (0.0020 in.)
15. INSPECT BRAKE LININGS AND DRUMS FOR PARKINGBRAKE
(a) Check the lining±to±drum contact condition and lining wear.
Minimum lining thickness:
1.0 mm (0.039 in.)
MA±12±
MAINTENANCE (1UZ ± FE)
WhereEverybodyKnowsYourName