turn LEXUS SC300 1999 Service Manual

COMFORT ADJUSTMENT
101
CAUTION

After the seat returns, try pushing the seat forward and
rearward to make sure it is secured in place.

Never allow anyone to rest their foot on the release pedal
while the vehicle is moving.

COMFORT ADJUSTMENT
102
HEAD RESTRAINTS
To raise the head restraint, pull it up. To lower it, press the
lock release button and push the head restraint down. To
move the head restraint forward, pull on the top.
Pulling the top of the head restraint forward as far as it can go
will return it to the upright position.
The head restraint is most effective when it is close to your
head. Therefore, using a cushion on the seatback is not
recommended.

COMFORT ADJUSTMENT
106Auto mode
When the tilt and telescopic steering wheel auto mode button
on the steering column is set to the ºONº position, the current
position of the steering column becomes the memorized
position.
When the ignition key is removed with the auto mode
button set to the ºONº position, the steering column
moves forward away from the driver and also tilts up for
easy exit and entry.
When the key is inserted in the ignition, the steering column
returns to the previously set position. This occurs regardless
of whether the auto mode button is ON or OFF.

COMFORT ADJUSTMENT
113
INSIDE REAR VIEW MIRROR
Adjust the mirror so that you can just see the rear of your
vehicle in the mirror.
Pushing the switch changes the mode between ºAUTOº
and ºDAYº.
The indicator comes on when the ºAUTOº mode is selected.
ºDAYº mode: The mirror surface is normal.
ºAUTOº mode: If the mirror detects light from the
headlights of the vehicle behind you, the mirror surface
darkens slightly to reduce the reflected light.
When the inside rear view mirror surface changes, the outside
rear view mirror surfaces will also become darker.
When the ignition key is inserted and turned on, the inside rear
view mirror always turns on in the ºAUTOº mode. When the outside air temperature is low, it may take a little
longer for the mirror to darken in response to the detection of
headlights.

COMFORT ADJUSTMENT
129
CAUTION
The driver or front passenger too close to the steering wheel
or dashboard during airbag deployment can be killed or
seriously injured. Lexus strongly recommends that:

The driver sit as far back as possible from the steering
wheel while still maintaining control of the vehicle.

The front passenger sit as far back as possible from the
dashboard.

All vehicle occupants be properly restrained using the
available seat belts.
This indicator comes on when the ignition key is turned to
the ºACCº or ºONº position. It goes off after about 6
seconds. This means the SRS airbags are operating
properly.
The SRS airbag warning light system monitors the airbag
sensor assembly, inflators, warning light, interconnecting
wiring and power sources. (For details, see ºService
reminder indicators and warning buzzersº on page 53 for
instructions.)

COMFORT ADJUSTMENT
141
This SRS airbag system has a service reminder indicator to
inform the driver of operating problems. If either of the
following conditions occurs, this indicates a malfunction of
the airbags. Contact your Lexus dealer as soon as possible to
service the vehicle.

The light does not come on when the ignition key is turned
to the ºACCº or ºONº position, or remains on.

The light comes on while driving.

THEFT DETERRENT
173
Setting the system
1. Turn the ignition key to the ºLOCKº position and
remove it.
The indicator light flashes by means of the engine
immobiliser system.
2. Close and lock all the doors, trunk and hood using an
ignition key or wireless remote control.If you lock them with wireless remote control, the turn signals
flash once.
The flashing indicator light changes to stay on when all the
doors, trunk and hood are closed and locked.
3. After 30 seconds, the indicator starts flashing and the
system is set.
Cancelling the system
When you unlock any door or trunk using an ignition key
or wireless remote control, the system is cancelled.
If you unlock any door or trunk with wireless remote control,
the turn signals flash twice.
Activating the system
The alarm sounds for 60 seconds if any of the following are
operated:


Unlocking any door or trunk without using an ignition key
or wireless remote control.

Opening the hood forcibly.

Reconnecting the battery.
If any door is unlocked and the ignition key is not in the
ignition switch during the alarm sounding, its door is
automatically locked.

THEFT DETERRENT
174To stop the alarm: Use either of the following methods.


Unlock the door or trunk using an ignition key or wireless
remote control.

Turn the ignition switch on.
Testing the system
1. Open all the windows.
2. Set the system as described above.
The front doors should be locked with the ignition key or
wireless remote control. Be sure to wait until the indicator
light starts flashing.
3. Unlock one of the doors from the inside.
The system should activate the alarm.
4. Unlock any of the doors with a key or the wireless
remote control to cancel the system.
5. Repeat this operation for the other doors and hood.
When testing the hood, also check that the system is activated
when the battery terminal is disconnected and then
reconnected.
If the system does not work properly, have it checked by your
Lexus dealer.
NOTICE
Disconnecting the battery may result in the erasure of
information you have set in the computer memory. After
reconnecting the battery, check that the memorized data
has been retained. If it has been erased, input it into the
computer once more.

AIR CONDITIONING AND AUDIO
181
(a) Climate control
SETTING OPERATION ± automatic control
1. Push the ºAUTOº knob.
Air flow quantity, switching of the diffusers, on±off of the air
conditioning, and switching of the air intake between
RECIRCULATED AIR and OUTSIDE AIR are
automatically adjusted. The operation status is shown by
each indicator.
When one of the manual control buttons is depressed while
operating in automatic mode, the operation corresponding to
the button depressed is set. Other conditions continue to be
adjusted automatically. 2. Turn the ºTEMPº knob until the desired temperature
is displayed.
The ºTEMPº knob is used to set the desired passenger
compartment temperature. The temperature of air delivered
to the passenger compartment will be controlled
automatically according to the setting. The figures on the
panel indicate degrees Fahrenheit.
SETTING OPERATION ± manual control
If manual air flow selection is desired ±
The outlets from which air is delivered can be selected
manually by pushing either side of the air flow control
(MODE) button. The mode appears on the display.
The function of each mode is as follows:
PANEL mode ± Directs air flow at face level.
BI±LEVEL mode ± Directs air flow at face level and
at floor level for both front and rear. Except in ventilation, the
air to the floor is slightly warmer than air to the face.
FLOOR mode ± Directs air flow mostly at floor level
for both front and rear.
FLOOR/WINDSHIELD mode ± Directs air flow to
the windshield and front side windows as well as floor level
for both front and rear.
FRONT WINDSHIELD mode ± Directs air flow
mostly to the windshield and front side windows.
When this mode is selected while operating in automatic
mode, the air conditioning is set to operate and the OUTSIDE

AIR CONDITIONING AND AUDIO
182AIR mode is set.
If you push the ºFRONT WINDSHIELDº button once again
while in the FRONT WINDSHIELD mode, the mode then
returns to the last mode used.
CAUTION
Do not use the FRONT WINDSHIELD mode during cooled
air operation in extremely humid weather. The difference
between the temperature of the outside air and that of the
windshield could cause the outer surface of the windshield to
fog up blocking your vision.
If quick heating or cooling is desired ±
Obtain maximum power by turning the ºTEMPº knob fully.
At this time, ºMAX. HOTº or ºMAX. COLDº will appear on
the display.
If manual fan speed control is desired ±
The fan speed can be set to your desired speed by pushing
either
side of the fan speed control
(FAN) button. The
higher the fan speed is, the more air is delivered. Pushing in
the
(OFF) button turns off the fan.
To remove exterior windshield frost, use the high speed
setting. Stopping the fan ±
Push in the
(OFF) button.
The fan stops in automatic mode or manual mode.
If manual switching of air intake is desired ±
(AIR INTAKE) button is used to switch the air
intake between the OUTSIDE AIR mode and
RECIRCULATED AIR mode.
With the button in the OUTSIDE AIR mode, the OUTSIDE
AIR mode indicator light will come on and the system will
take fresh outside air into the vehicle.
If quick circulation of cooled air is desired, press in the air
intake control button for RECIRCULATED AIR. The
RECIRCULATED AIR mode indicator light will come on.
For normal use, it is best to keep the air intake control button