key LEXUS SC300 1999 Workshop Manual

COMFORT ADJUSTMENT
129
CAUTION
The driver or front passenger too close to the steering wheel
or dashboard during airbag deployment can be killed or
seriously injured. Lexus strongly recommends that:

The driver sit as far back as possible from the steering
wheel while still maintaining control of the vehicle.

The front passenger sit as far back as possible from the
dashboard.

All vehicle occupants be properly restrained using the
available seat belts.
This indicator comes on when the ignition key is turned to
the ºACCº or ºONº position. It goes off after about 6
seconds. This means the SRS airbags are operating
properly.
The SRS airbag warning light system monitors the airbag
sensor assembly, inflators, warning light, interconnecting
wiring and power sources. (For details, see ºService
reminder indicators and warning buzzersº on page 53 for
instructions.)

COMFORT ADJUSTMENT
141
This SRS airbag system has a service reminder indicator to
inform the driver of operating problems. If either of the
following conditions occurs, this indicates a malfunction of
the airbags. Contact your Lexus dealer as soon as possible to
service the vehicle.

The light does not come on when the ignition key is turned
to the ºACCº or ºONº position, or remains on.

The light comes on while driving.

COMFORT ADJUSTMENT
168
2. To remove the child restraint system, press the
buckle±release button and allow the belt to retract.DRIVING POSITION MEMORYSYSTEM
The micro computer can memorize the position of the driver's
seat, the positions of the tilt and telescopic steering, and
outside rear view mirrors. Two different driving position
profiles can be entered into the computer's memory.
This can only be done when the ignition key is in the ºONº
position, and the selector lever is in the ºPº position.
Setting a driving position

COMFORT ADJUSTMENT
170
When you push button º1º or º2º, the signal beeps and the
driving position automatically adjusts to the position
recorded for that button.
Conditions for memorized position activation

Ignition key ºONº
Selector lever in ºPº position
All parts of the memorized positions can be activated.
However, if the brake pedal is being depressed, the seat
position will not change.

Key not in ignition switch
Within 30 seconds of opening driver's door
The memorized position can be activated, except for the
tilt and telescopic steering. If any driving position memory switch is pushed while one of
the memorized driving position profiles is being activated,
the operation will stop.
To activate the system, push the desired button (º1º or º2º)
again.
The driving position memory control system cannot be
operated while the vehicle is moving.
If the vehicle's battery is disconnected, the computer's
memory
will be erased and the memorized positions will have
to be set again.

THEFT DETERRENT
173
Setting the system
1. Turn the ignition key to the ºLOCKº position and
remove it.
The indicator light flashes by means of the engine
immobiliser system.
2. Close and lock all the doors, trunk and hood using an
ignition key or wireless remote control.If you lock them with wireless remote control, the turn signals
flash once.
The flashing indicator light changes to stay on when all the
doors, trunk and hood are closed and locked.
3. After 30 seconds, the indicator starts flashing and the
system is set.
Cancelling the system
When you unlock any door or trunk using an ignition key
or wireless remote control, the system is cancelled.
If you unlock any door or trunk with wireless remote control,
the turn signals flash twice.
Activating the system
The alarm sounds for 60 seconds if any of the following are
operated:


Unlocking any door or trunk without using an ignition key
or wireless remote control.

Opening the hood forcibly.

Reconnecting the battery.
If any door is unlocked and the ignition key is not in the
ignition switch during the alarm sounding, its door is
automatically locked.

THEFT DETERRENT
174To stop the alarm: Use either of the following methods.


Unlock the door or trunk using an ignition key or wireless
remote control.

Turn the ignition switch on.
Testing the system
1. Open all the windows.
2. Set the system as described above.
The front doors should be locked with the ignition key or
wireless remote control. Be sure to wait until the indicator
light starts flashing.
3. Unlock one of the doors from the inside.
The system should activate the alarm.
4. Unlock any of the doors with a key or the wireless
remote control to cancel the system.
5. Repeat this operation for the other doors and hood.
When testing the hood, also check that the system is activated
when the battery terminal is disconnected and then
reconnected.
If the system does not work properly, have it checked by your
Lexus dealer.
NOTICE
Disconnecting the battery may result in the erasure of
information you have set in the computer memory. After
reconnecting the battery, check that the memorized data
has been retained. If it has been erased, input it into the
computer once more.

AIR CONDITIONING AND AUDIO
180The automatic air conditioning automatically maintains the
set temperature.
This air conditioning features automatic fan speed and air
flow
control which automatically selects the most suitable fan
speed and air flow to control the temperature. The ignition
key must be in the ºONº position.
You may use manual control to override the automatic
settings.
You can adjust the brightness of the display. See ºInstrument
panel light controlº on page 64 for details.

AIR CONDITIONING AND AUDIO
187
To prevent the battery from being discharged, do not leave
the car audio on longer than necessary when the engine
is not running.
To ensure the correct audio system operation:


Be careful not to spill beverages over the audio system.

Do no put anything other than a cassette tape or CD
magazine into the cassette tape slot or CD changer.

The use of cellular phone inside or near the vehicle
may cause a noise from the speakers of the audio
system which you are listening to. However, this does
not indicate a malfunction.
You can listen to the car audio when the ignition key is at
ºONº or ºACCº. However, if the engine is not running,
the key must be in the ºACCº position.
You can adjust the brightness of the display. See ºInstrument
panel light control on page 64 for details.
Audio operation is described in detail on the following pages:

Radio operation ± See page 187.

Cassette tape player operation ± See page 192.

Compact disc player operation ± See page 196.
Radio operation
(a) Listening to the radio
1. Push the
(AM) or (FM1/2) button to turn the
radio on and select either an AM or FM broadcast.
ºAMº, ºFM1º or ºFM2º will appear on the display.
The radio can also be turned on by pushing the ºPWR.VOLº
knob if the radio was being used when the system was turned
off.
2. Turn the ºPWR.VOLº knob to adjust the volume.
3. Tune in the desired station. (See º(b) Selecting a stationº.)
The radio will change automatically to stereo reception when
an FM stereo broadcast is being received. At the same time
ºSTº will appear on the display. When the receiving signal
gets weak, the channel separation will automatically be
reduced for lowest noise. If the signal becomes extremely
weak, the radio will switch over to monaural reception.
4. Adjust the tone and sound balance. (See º(d) Adjusting the
toneº and º(e) Adjusting the sound balanceº.)
5. To turn the radio off, push the ºPWR.VOLº knob.

AIR CONDITIONING AND AUDIO
193
*Dolby noise reduction manufactured under license from Dolby
Laboratories Licensing Corporation. ºDOLBYº and the double±D
symbol
are trademarks of Dolby Laboratories Licensing
Corporation.
3. Turn the ºPWR.VOLº knob to adjust the volume.
4. Select your program. (See º(b) Selecting a programº.)
5. Adjust the tone and sound balance. (See º(d) Adjusting the
toneº and º(e) Adjusting the sound balanceº of radio
operation.)
6. If desired, other functions may be used for your
convenience. (See º(c) Other tape player functionsº.)
7. To turn the player off, push the ºPWR.VOLº knob.
8. To eject the cassette, push the
(EJECT) button. As this
is done, the player will turn off. If the radio was on when the
cassette tape was inserted, it will automatically turn on again.
The ignition key can be at any position to eject the cassette.
(b) Selecting a program
1. Push the left side of
(PROG) button to select a
side to play. The tape operation indicator display shows you
which side is being played.
The player will automatically reverse directions at the end of
the tape to play the other side.
2. Play the program you want using either of the following
methods. Manual program selection
Push the
(REW, FF) button on the right side to fast
forward the tape or on the left side to rewind the tape. At this
time, ºFFºor ºREWº will appear on the display. To stop
either fast forwarding or rewinding, push the button on the
same side again or push the
(TAPE) button. The tape
will then resume playing.
ºAutomatic program selectionº button: The automatic
program selection feature allows you to program your
cassette player to skip forward or backward to locate the song
you want to hear. You can skip up to nine programs at a time.
Push
(TRACK) button on the upper side to skip forward.
ºFFº and the number will appear on the display. Push the
button until the number you want to skip appears on the
display. After that, the player will automatically skip
forward.
When the end of the tape is reached, the player automatically
reverses sides and resumes normal play.
Push
(TRACK) button on the lower side to skip backward.
Push the button until ºREWº and the number you want to skip
appear on the display.

If you set ºREW 1º, the player will rewind to the
beginning of the current program.

When counting the number of programs you want to
rewind, remember to count the current program as well.
For example, if you want to rewind to a song that is two
before the song you are listening to, push this button until

STARTING AND DRIVING
212
To allow proper operation of your vehicle's
ventilation system, keep the inlet grilles in front of
the windshield clear of snow, leaves, or other
obstructions.
 If you smell exhaust fumes in the vehicle, drive with
the windows open and the trunk lid closed. Have the
cause immediately located and corrected.
BEFORE STARTING THE
ENGINE
1. Check the area around the vehicle before entering it.
2. Adjust seat position, seatback angle, head restraint height
and steering wheel angle.
3. Adjust inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts.
Remember to check that the service reminder indicators
function when turning the key to ºONº, and check the fuel
gauge to see that you have sufficient fuel.
IGNITION SWITCH WITH
STEERING LOCK