turn LEXUS SC300 1999 Manual Online

DRIVING TIPS
271
Supplement/Maintenance Scheduleº.)
CAUTION
Never turn off the engine to coast down hills. Your power
steering and brake booster will not function without the
engine running. Also, the emission control system operates
properly only when the engine is running.

IN CASE OF AN EMERGENCY
274
IF YOUR ENGINE STALLSWHILE DRIVING
If your engine stalls while driving . . . .
1. Reduce your speed gradually, keeping a straight line.
Move cautiously off the road to a safe place.
2. Turn on your emergency flashers.
3. Try starting the engine again.
If the engine will not start, see ºIf your vehicle will not startº.
CAUTION
If the engine is not running, the power assist for the brakes and
steering will not work, so steering and braking will be much
harder than usual.

IN CASE OF AN EMERGENCY
275
IF YOUR VEHICLE WILL NOTSTART
(a) Simple checks
Before making these checks, make sure you have followed
the correct starting procedure instructions in ºHow to start the
engineº on page 216 and that you have sufficient fuel. Since
your vehicle is equipped with the engine immobiliser system,
also check whether the other keys will start the engine. If they
work, your key may be broken. Have the key checked at your
Lexus dealer. If none of your keys work, the system is
possibly broken. Call your Lexus dealer. See ºKeysº on page
12. If the engine is not turning over or is turning over too
slowly ±
1. Check that the battery terminals are tight and clean.
2. If the battery terminals are O.K., switch on the interior
light.
3. If the light is out, dim or goes out when the starter is
cranked,
the battery is discharged. You may try jump starting.
See º(c) Jump startingº for further instruction.
If the light is O.K., but the engine still will not start, it needs
adjustment or repair. Call a Lexus dealer, Roadside
Assistance or Customer Service Assistance. (See
ºForewordº.)
NOTICE
Do not pull±or push±start the vehicle. It may damage the
vehicle or cause a collision when the engine starts. Also
the three±way catalytic converter may overheat and
become a fire hazard.
If the engine turns over at its normal speed but will not
start ±
1. The engine may be flooded because of repeated cranking.
See º(b) Starting a flooded engineº for further instructions.
2. If the engine still will not start, it needs adjustment or
repair. Call a Lexus dealer, Roadside Assistance or Customer
Service Assistance. (See ºForewordº.)

IN CASE OF AN EMERGENCY
276
(b) Starting a flooded engine
If the engine will not start, your engine may be flooded
because of repeated cranking.
If this happens, turn the key to ºSTARTº with the accelerator
pedal held down. Continue this operation for 30 seconds and
then stop cranking. Then try starting the engine with your foot
off the accelerator pedal.
If the engine does not start after 30 seconds of cranking,
release the key, wait a few minutes and try again.
If the engine still will not start, it needs adjustment or repair.
Call a Lexus dealer, Roadside Assistance or Customer
Service Assistance. (See ºForewordº.)
NOTICE
Do not crank for more than 30 seconds at a time. This
may overheat the starter and wiring systems.
(c) Jump starting
To avoid serious personal injury and damage to your
vehicle which might result from battery explosion, acid
burns, electrical burns, or damaged electronic
components, these instructions must be followed
precisely.
If you are unsure about how to follow this procedure, we
strongly recommend that you seek help from your Lexus
dealer, Roadside Assistance or Customer Service Assistance.

IN CASE OF AN EMERGENCY
279
JUMP STARTING PROCEDURE
1. If the booster battery is installed in another vehicle, make
sure the vehicles are not touching. Turn off all unnecessary
lights and accessories.
2. If required, remove all the vent plugs from the booster
battery.
Lay a cloth over the open vents on the booster battery.
(This helps reduce the explosion hazard, personal injuries and
burns.)
3. If the engine in the vehicle with the booster battery is not
running, start it and let it run for about 5 minutes. During
jump starting, run the engine at about 2000 rpm with the
accelerator pedal lightly depressed.
4. Connect the jumper cables in the exact order shown in the
illustration: positive terminal (º+º mark)±to±positive
terminal (º+º mark), and negative terminal (º±º
mark)±to±engine or body ground. Note that you first connect
the positive cable to the discharged battery and then to the
booster battery. Next, connect the negative cable to the
booster battery and then to a solid, stationary, unpainted
metallic point (e.g. SC400: brake booster vacuum pipe
bracket, SC300: cylin der head) away from the battery. Do not
connect it to or near any part that moves when the engine is
cranked.
CAUTION
When making the connections, to avoid serious injury, do not
lean over the battery or accidentally let the jumper cables or
clamps touch anything except the correct battery terminals or
the ground.

IN CASE OF AN EMERGENCY
281
When the engine overheats
Pull safely off the road, stop the vehicle and turn on your
emergency flashers. Put the transmission in ºPº and apply the
parking brake.
A: If steam is coming from your engine:
Turn off the engine. Leave the hood closed until there is no
sign of steam or coolant. Your engine could have been
seriously damaged already. Call your Lexus dealer for
assistance.
CAUTION
To help avoid personal injury, keep the hood closed until there
is no steam. Escaping steam or coolant is sign of very high
pressure.

IN CASE OF AN EMERGENCY
282B: If no steam is coming from your engine:
Leave the engine running and turn off the air conditioning.
Check the following.


Is the cooling fan operating?

Is the coolant in the acceptable range?

Is the engine drive belt O.K.?
CAUTION

When the engine is running, keep hands and clothing away
from the moving fan and engine drive belt.

Do not attempt to remove the radiator cap when the engine
and radiator are hot. Serious injury could result from
scalding hot fluid and steam blown out under pressure.
If the cooling fan is not operating or the coolant is not in the
acceptable range, turn off the engine and call your Lexus
dealer.
If both conditions are O.K., after the engine coolant
temperature has cooled to normal, continue driving your
vehicle.
If the engine coolant temperature does not cool down, or your
vehicle overheats again, have it checked as soon as possible
by your Lexus dealer.

IN CASE OF AN EMERGENCY
283
IF YOU HAVE A FLAT TIRE
1. Reduce your speed gradually, keeping a straight line.
Move cautiously off the road to a safe place ± well away from
the traffic. A void stopping on the center divider of a highway.
Park on a level spot with firm ground.
2. Stop the engine and turn on your emergency flashers.
3. Firmly set the parking brake and put the transmission in
ºPº.
4. Have everyone get out of the vehicle on the side away from
traffic.
5. Read the following instructions thoroughly.
CAUTION
When jacking, be sure to observe the following to reduce the
possibility of personal injury:

Follow jacking instructions.

Do not put any part of your body under a vehicle supported
by a jack. Personal injury may occur.

Do not start or run the engine while your vehicle is
supported by the jack.

Stop the vehicle on a level firm ground, firmly set the
parking brake and put the transmission in ºPº. Block the
wheel diagonally opposite to the one being changed if
necessary.

IN CASE OF AN EMERGENCY
285
When removing the jack, turn the joint by hand in the
CONTRACT direction until the jack is free. When storing,
turn the joint by hand in the EXPAND direction until the jack
is firmly secured to prevent it from flying forward during a
collision or sudden braking.

IN CASE OF AN EMERGENCY
288
3. Loosen all the wheel nuts.
Always loosen the wheel nuts before raising the vehicle.
Turn the nuts counterclockwise to loosen them. To get
maximum leverage, fit the wrench to the nut so that the handle
is on the right side, as shown above. Grab the wrench near the
end of the handle and pull up on the handle. Be careful that
the wrench does not slip off the nut.
Do not remove the nuts yet ± just unscrew them about
one±half turn.