LEXUS SC400 1991 Service Repair Manual
Page 3081 of 4087
±
STEERING STEERING COLUMNSR±59
WhereEverybodyKnowsYourName
Page 3082 of 4087
SR±60±
STEERING STEERING COLUMN
WhereEverybodyKnowsYourName
Page 3083 of 4087
LOCATION OF CONNECTORS IN SEAT
±
STEERING STEERING COLUMNSR±61
WhereEverybodyKnowsYourName
Page 3084 of 4087
SR±52).
IN±33).
WIRING DIAGRAM
CIRCUIT INSPECTION
ECU Power Source Circuit
CIRCUIT DESCRIPTION
The ECU power source also supplies power to the CPU and sensor, etc. Power is supplied to the ECU even
when the ignition switch is off.
DIAGNOSTIC CHARTDIAGNOSTIC CHART
SR±62±
STEERING STEERING COLUMN
WhereEverybodyKnowsYourName
Page 3085 of 4087
NGOK
OKNG
INSPECTION PROCEDURE
1Check voltage between terminals ECU±B and ECU±E of ECU connector.
C
OK
PRemove ECU with connectors still connected.
Measure voltage between terminals ECU±B and ECU±
E of ECU connector.
Voltage: 10 ~ 14 V
Proceed to next circuit inspection shown on matrix chart
(See page SR±52).
2Check continuity between terminal ECU±E of ECU connector and body gro\
und.
C
OK
Measure resistance between terminal ECU±E of ECU
connector and body ground.
Resistance: 1 or less
Repair or replace harness or connector.
Go to Step .
±
STEERING STEERING COLUMNSR±63
WhereEverybodyKnowsYourName
Page 3086 of 4087
OKNG
3Check DOME Fuse.
C
OK
PRemove DOME Fuse from R/B No. 2.
Check continuity of DOME Fuse.
Continuity
Check for short in all the harness and components con-
nected to DOME Fuse (See attached wiring diagram).
Check harness and connector between ECU and
battery (See page
IN±33).
SR±64±
STEERING STEERING COLUMN
WhereEverybodyKnowsYourName
Page 3087 of 4087
±MEMO±
±
STEERING STEERING COLUMNSR±65
WhereEverybodyKnowsYourName
Page 3088 of 4087
DTC53Short in Squib Circuit (Between P+ Wire Harness
P
± Wire Harness)
CIRCUIT DESCRIPTION
The squib circuit consists of the center airbag sensor assembly, (squib). It causes the SRS to deploy when the
SRS deployment conditions are satisfied.
For details of the function of each component, see FUNCTION OF COMPONENTS o\
n page RS±10. Diagnostic
trouble code 53 is recorded when an short is detected in the P
+ wire harness and P± wire harness of the squib
circuit.
DTC No.Diagnosis
53
Short circuit between P+ wire harness and P± wire harness of squib.
Squib malfunction.
Center airbag Sensor Assembly malfunction.
DIAGNOSTIC CHARTDIAGNOSTIC CHART
RS±110±
SUPPLEMENTAL RESTRAINT SYSTEM TROUBLESHOOTING
WhereEverybodyKnowsYourName
Page 3089 of 4087
WIRING DIAGRAM
DIAGNOSTIC CHARTDIAGNOSTIC CHART
±
SUPPLEMENTAL RESTRAINT SYSTEM TROUBLESHOOTINGRS±111
WhereEverybodyKnowsYourName
Page 3090 of 4087
OKNG
INSPECTION PROCEDURE
1Preparation.
P1. Disconnect battery negative (±) terminal cable, andwait at least 90 seconds.
2. Remove steering wheel pad (See page RS±19).
3. Disconnect connectors of front passenger airbag assembly (See page RS±32).
Caution: Store the steering wheel pad with the
surface facing upward.
2Check P squib circuit.
C
OK
Measure resistance between P+ and P± on center air-
bag sensor assembly side of connector between center
airbag sensor assembly and front passenger airbag as-
sembly.
Resistance: 1 k or higher
Go to step .
RS±112
±
SUPPLEMENTAL RESTRAINT SYSTEM TROUBLESHOOTING
WhereEverybodyKnowsYourName