bulb LINCOLN MARK VIII 1998 Owners Manual

Speed control (if equipped)
This light comes on when either the
SET/ACCEL or RESUME controls
are pressed. It turns off when the
speed control OFF control is
pressed, the brake is applied or the
ignition is turned to the OFF
position.
High beams
Illuminates when the high beam
headlamps are turned on.
Redundant electronic gearshift indicator
These lights operate with the key in
the ON position only and display the
same gear selection as shown on the
gear selector indicator located on
the floor console next to the
gearshift lever.
Turn signal
Illuminates when the left or right
turn signal or the hazard lights are
turned on. If one or both of the
indicators stay on continuously or
flash faster, check for a burned-out
turn signal bulb. Refer toExterior
bulbsin theMaintenance and care
chapter.
CRUISE
ON
P
R
N
D
2
1
Instrumentation
8

Message center warning lights
The following warning lights are displayed directly above the message
center controls.
Safety belt
Illuminates when the ignition is
turned on to remind you to fasten
your safety belts. For more
information, refer to theSeating
and safety restraintschapter.
Check engine
Your vehicle is equipped with a
computer that monitor's the engine's
emission control system. This
system is commonly known as the
On Board Diagnostics System (OBD
II). This OBD II system protects the
environment by ensuring that your
vehicle continues to meet
government emission standards. The OBD II system also assists the
service technician in properly servicing your vehicle.
Thecheck engineindicator light illuminates when the ignition is first
turned to the ON position to check the bulb. If it comes on after the
VEHICLE
SETTINGDRIVER
SETTINGTRIP
ODO RANGE
RESET
N
S W
E
FUELECONOMY
DATE
TIMESYSTEM
CHECK
CHECK
ENGINEO/D
OFFANTI
THEFTT/C
OFF
CHECK
ENGINE
Instrumentation
9

TRANSMISSION OVERHEAT. Indicates the transmission is
overheating. This warning may appear when towing heavy loads or when
driving in a low gear at a high speed for an extended period of time.
Stop the vehicle as soon as safely possible, turn off the engine and let it
cool. Check the transmission fluid and level. Refer toTransmission
fluidin theMaintenance and carechapter. If the warning stays on or
continues to come on, contact your dealer for transmission service as
soon as safely possible.
CHECK BRAKE LAMPS. Displayed when the brake lamps are
activated and at least one is burned out. Check the lamps as soon as
safely possible and have the burned out lamp replaced. The center
high-mount brakelamp is not monitored.
CHECK HEADLAMPS. Displayed when the headlamps are activated
and at least one is burned out. Check the lamps as soon as safely
possible and have the burned out lamp replaced. Refer toReplacing
headlamp bulbsin theMaintenance and carechapter. The high beam
lamps are not monitored.
CHECK TAIL LAMPS. Displayed when the tail lamps are activated and
at least one is burned out. Check the lamps as soon as safely possible
and have the burned out lamp replaced.
CHECK FRT TURN LAMPS. Displayed when the turn signals are
activated and at least one is burned out. Check the lamps as soon as
safely possible and have the burned out lamp replaced.
LOW WASHER FLUID. Indicates there is less than one quarter of
washer fluid left in the reservoir. Check the washer fluid level. Refer to
Windshield washer fluidin theMaintenance and carechapter.
TRUNK AJAR. Displayed when the trunk is not completely closed and
the ignition switch is in ON or ACC.
CHECK TRACTION CONTROL. Displayed when the Traction
Controlysystem is not operating properly. If this message is displayed
on the message centerandthe green T/C OFF light isnotilluminated,
the Traction Controlysystem will be partially operable. If this warning
stays on, contact your dealer for service as soon as possible. For further
information, refer toTraction controlyin theDrivingchapter.
AIR RIDE SWITCH OFF. Displayed when the air suspension switch is
in the OFF position.
Instrumentation
29

sells, leases, trades vehicles, or supervises a fleet of vehicles are not
permitted to intentionally remove an emission control device or prevent
it from working. Information about your vehicle's emission system is on
the Vehicle Emission Control Information Decal located on or near the
engine. This decal identifies engine displacement and gives some tune up
specifications.
Please consult your ªWarranty Guideº for complete emission warranty
information.
Readiness for inspection/maintenance (I/M) testing
In some localities, it may be a legal requirement to pass an I/M test of
the on-board diagnostic (OBD-II) system. If your ªcheck engine/service
engine soonº light is on, reference the applicable light description in the
Warning Lights and Chimessection of your owners guide. Your vehicle
may not pass the I/M test with the ªcheck engine/service engine soonº
light on.
If the vehicle's powertrain system or its battery has just been serviced,
the OBD-II system is reset to a ªnot ready for I/M testº condition. To
ready the OBD-II system for I/M testing, a minimum of 30 minutes of city
and highway driving is necessary as described below:
²First, at least 10 minutes of driving on an expressway or highway.
²Next, at least 20 minutes driving in stop and go, city type traffic with
at least four idle periods.
Allow the vehicle to sit for at least eight hours without starting the
engine. Then, start the engine and complete the above driving cycle. The
engine must warm up to its normal operating temperature. Once started,
do not turn off the engine until the above driving cycle is complete.
EXTERIOR BULBS
Replacing exterior bulbs
Check the operation of the following lamps frequently:
²Headlamps
²Tail lamps
²Brakelamps
²High-mount brakelamp
²Turn signals
Maintenance and care
145

²Backup lamps
²License plate lamp
Do not remove lamp bulbs unless they will be replaced immediately. If a
bulb is removed for an extended period of time, contaminants may enter
the lamp housings and affect performance.
Replacing headlamp bulbs
The high beam headlamps on your vehicle use halogen bulbs. If the lamp
burns out, simply replace it with a new one.
Handle a halogen headlamp bulb carefully and keep out of
children's reach. Grasp the bulb only by its plastic base and do
not touch the glass. The oil from your hand could cause the bulb to
break the next time the headlamps are operated.
Unlike the high beam headlamps, the low beam headlamps on your
vehicle use a ªhigh intensity dischargeº source. These lamps operate at a
high voltage.
Low beam headlamps that flicker, are dim, or appear yellow or red
should be replaced using the following instructions provided the vehicle
is equipped with an orange sticker displayed near the front of the engine
compartment which reads WARNING: HIGH VOLTAGE.
Take your vehicle to your Lincoln Mercury dealer for service if:
²One or both of your low beam headlamp bulbs are burned out and the
orange sticker which reads WARNING: HIGH VOLTAGE is not
displayed near the front of the engine compartment or
²The message center displays ªCHECK HEADLAMPS.º
Replacing the low beam headlamp bulb
1. Make sure the headlamp switch is
in the OFF position.
2. Lift the hood and disconnect the
battery ground cable.
3. Remove the sight shield located
above the headlamps.
Maintenance and care
146

9. Remove the headlamp bulb
retaining nuts.
10. Remove the headlamp bulb
assembly.
11. Slide the headlamp level and
bracket off the bulb assembly and
remove.
12. Twist headlamp housing
counterclockwise to remove
headlamp bulb from socket.
Maintenance and care
148

To install the new low beam headlamp bulb:
1. Insert the new bulb into the
socket and twist clockwise to lock
into place.
2. Pull the headlamp level and
bracket over the bulb assembly and
snap into place.
3. Insert the bulb assembly into the
socket opening.
4. Install the retaining nuts. Tighten
them 1/4 turn past finger tight.
Maintenance and care
149

5. Position the low beam headlamp
housing cover over the bulb
assembly and rotate clockwise to
lock into place.
6. Match the remaining wire
connectors with their proper mates
and reinstall.
7. Reinstall the top bolts. Tighten
1/2 turn past finger tight.
8. Reinstall the retaining screw at
the corner of the headlamp
assembly.
Maintenance and care
150

9. Replace the sight shield.
10. Reconnect the battery ground
cable and close the hood.
Replacing the high beam headlamp bulb
To remove the high beam headlamp bulb:
1. Make sure the headlamp switch is
in the OFF position.
2. Lift the hood and remove the
sight shield located above the
headlamps.
3. Remove the high beam headlamp
housing cover by rotating it 1/4 turn
counterclockwise.
Maintenance and care
151

4. Rotate the plastic bulb base
counterclockwise and pull the bulb
assembly out of the housing.
5. Pull the bulb socket retaining clip
outward while carefully pulling up
on the plastic base of the bulb.
To install the new high beam headlamp bulb:
1. Hold the bulb by its plastic base
and insert it into the socket.
Maintenance and care
152