LUCID AIR 2022 Owners Manual

When the gear is in D (Drive) or N (Neutral)
and forward vehicle motion is detected, Cross
Traffic Protection will sound an alert and
prompt on the Cockpit Panel when a collision risk is detected.
If the vehicle is moving and the driver does
not react in time, the system will activate
emergency braking.
When the gear is in R (Reverse) or N (Neutral)
and backward vehicle motion is detected,
Cross Traffic Protection will sound an alert
and prompt on the right Cockpit Panel when a
collision risk is detected.
If the vehicle is moving and the driver does
not react in time, the system will activate emergency braking.
Cross Traf

corrections, audible alerts will be longer induration.
Lane Departure Protection alerts will be
canceled immediately if any of the following
actions happen:
-A turn signal is activated
- Intentional steering
- Intentional acceleration
- Intentional braking
Lane Departure Protection settings
To configure Lane Departure Protection, from
the Pilot Panel touch
> DreamDrive,
then enable or disable Lane Departure Protection. Settings save to the current User
Profile.
When Lane Departure Protection is
disabled or unavailable, an indicator
will display on the Cockpit Panel.
When enabled, press INTERVENTION ONLY (default) or WARNING AND INTERVENTION if
you wish to receive haptic vibrations of the
steering wheel when a steering correction is recommended.
Warnings cancel automatically when the risk of an unintentional lane departure has beenreduced (such as when you steer the vehicle
back to the current lane).
Blind Spot Warning
WARNING: Blind Spot Warning should
not be used as a replacement for
checking the interior and exterior
mirrors or looking over your shoulder
before changing lanes. It

Blind Spot Display uses the exterior cameras
to project an image of the blind spot field
of view onto the Cockpit Panel when a
turn signal is activated, helping the driver to
assess the surroundings. See Turn Signals.
Note: Blind Spot Display is only available at
speeds above 25 mph (40 km/h).
With Blind Spot Display enabled, activating a turn signal will bring the camera view up forthat side on the Center Cockpit Panel.
Blind Spot Display settings
To configure Blind Spot Display, from the
Pilot Panel touch
> DreamDrive, then
enable or disable Blind Spot Display on Glass
Cockpit. Settings save to the current User
Profile.
DreamDrive110

Parking Experience
Automatic Park InWARNING: Automatic Park In does
not consider objects located outside
the range of sensors during
the detection of parking spaces
or calculating the parking path.
Continually check your surroundings
throughout the parking sequence. Be
prepared to apply the brake and take
control to avoid pedestrians, vehicles,
or objects.WARNING: It is the driver

and will resume automatically when the
brake is released.
- If a system detects an obstacle in
the vehicle

holding the brake pedal while the vehicle
scans the available space.
When the system prompts you, release the brake and steering wheel to begin the pull-
out sequence. An audible alert will sound
when vehicle movement begins. A turn signal
activates in the direction you

-A safety system activates (such
as Collision Protection or Automatic
Emergency Braking. See Collision
Detection and Protection on page 105)
When the system is canceled, the vehicle will
stop, emit an audible alert, and prompt the
driver to take control of the steering wheel
and brake pedal. If there is no response from
the driver after 20 seconds, the gear will
automatically shift into P (Park).
If Automatic Park Out cancels for any of the
aforementioned reasons and you wish to use
the system again, you must start over at the
beginning of the process.
Surround View MonitoringWARNING: The Surround View
Monitoring system should not be
used as a replacement for looking
into the interior and exterior mirrors
or looking over your shoulder when
operating and parking the vehicle.
Always inspect your surroundings with
your own eyes.
The Surround View Monitoring system uses
the exterior cameras to display the immediate vehicle surroundings in real time. This system
assists you in situations such as parking or at
exits with reduced visibility.
Note: Surround View Monitoring is only
available when the vehicle

-The side mirrors are folded in
- The trunk or hood is open
Rear View MonitoringWARNING: The Rear View Monitoring
system should not be used as a
replacement for looking into the
interior and exterior mirrors or looking
over your shoulder when operating and parking the vehicle. Always
inspect your surroundings with your
own eyes.
Rear View Monitoring is an assist feature that
automatically displays the rear camera view
on the right Cockpit Panel when the vehicle
shifts into R (Reverse). See Selecting a Drive
Mode.
To manually activate Rear View Monitoring,
press
on the Pilot Panel.
To manipulate the camera view, do any of the
following:
-Swipe down on the screen to switch to
the front camera view, or swipe up forthe rear camera view.
- Pinch outward with two fingers on the
screen to zoom in the camera angle.
Reverse the gesture to zoom out.
Note: The current magnification level
will be displayed to the right of the
camera view.
- Press the +/- buttons to zoom the view
in/out.
- Press
to close the screen.
Park Distance Warning
WARNING: Park Distance Warning is
an assist feature only, and will notact to prevent a collision. It is the
driver

Distance Warning. Settings save to the current
User Profile.DreamDrive116

07Infotainment
Infotainment117