Start MAZDA CX90 2024 User Guide

Temporarily Deactivating the Rear
Seat Alert
When the instrument cluster displays a
message concerning the Rear Seat
Alert, the driver can temporarily
deactivate the system.
Operate according to the message
displayed in the instrument cluster.
When the message "Press and Hold
INFO Switch to Deactivate Rear Seat
Alert" is displayed in the instrument
cluster, press and hold the INFO switch
for 2 seconds or longer.
When the system is temporarily
deactivated, a chime sounds and a
message to notify that the operation
was completed appears in the
instrument cluster. The message
disappears after a short period of time.
NOTE
When the vehicle power is switched
OFF, the temporary deactivation is
canceled.
Turning the Rear Seat Alert Off
The Rear Seat Alert can be set to off
using Mazda Connect.
Refer to Mazda Connect Owner's
Manual or consult an Authorized
Mazda Dealer.
NOTE
Under the following conditions, the
warning light
turns on 2 times to
indicate the system has been stopped
when the vehicle power is switched
ON, and then turns off after a short
period of time.
The Rear Seat Alert is turned off.The Rear Seat Alert is temporarily
deactivated.
Remote engine starting via
Connected Service is used*.The lead-acid battery charge is low.
Opening/closing
Rear Seat Alert
4-44*Some models.
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Warnings and Cautionsfor Using the Mirrors
WARNING
Be sure to look over your shoulder
before changing lanes.
Changing lanes without taking into
account the actual distance of a vehicle
in the convex mirror is dangerous. You
could have a serious accident. What
you see in the convex mirror is closer
than it appears.
Always return the outside mirrors to
the driving position before you start
driving.
Driving with the outside mirrors folded
in is dangerous. Your rear view will be
restricted, which could lead to an
unexpected accident.

(Vehicles with electric retractable
mirrors)
Do not touch the outside mirrors
while they are folding in and out.
Touching an outside mirror while it is
folding in or out is dangerous. Your
hands could get caught which could
cause an injury or the door mirror
could be damaged.
Use the switch to set the outside
mirrors.
Setting the outside mirrors manually is
dangerous. The outside mirrors will not
lock into place, which could obstruct
visibility.
Always operate the electric retractable
mirrors with the vehicle parked in a
safe place.
Operating the electric retractable
mirrors while driving is dangerous.
Wind pressure could damage the
outside mirrors, making it impossible
to return them to the driving position
and to see behind you.
Do not adjust the outside mirrors
while driving the vehicle.
Adjusting the outside mirrors while
driving the vehicle is dangerous as
doing so could distract your attention
from the road ahead and lead to an
accident.
CAUTION
(Vehicles with electric retractable
mirrors)
Operate the folding switch to fold in or
out the outside mirrors. If you unfold
the outside mirrors manually, they will
not be in a secured position and you
will be unable to check the view to the
rear of the vehicle.
Driving
Mirrors
5-8
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Convenient Ways to Usethe Outside Mirrors
Driving Position Memory*
The angle of the outside mirrors can be
programmed to the Driving Position
Memory.
Refer to Driving Position Memory on
page 3-33.
Auto fold function
*
When locking/unlocking the doors
while the vehicle power is switched
OFF, the outside mirrors automatically
fold in and out.
When the outside mirrors are folded in
and the vehicle power is switched ON,
or the hybrid system is started, the
outside mirrors fold out automatically.
Turn the auto fold function on using
the center display.
Refer to Settings section in the Mazda
Connect Owner's Manual or consult
an Authorized Mazda Dealer.
Operation function after hybrid
system is stopped
The angle of the outside mirrors can be
adjusted and they can be folded in and
out for about 40 seconds after the
vehicle power is switched from ON to
OFF.
Auto tilt-down outside mirror
function for reversing *
The outside mirrors can be set to tilt
downwards automatically when
reversing the vehicle. When the vehicle
is finished reversing , the outside
mirrors return to their original angle.
1. Press the select switch on the side of the door mirror to be tilted
down.
Turn on the indicator light of the
select switch.
2. Shift the selector lever to the Rposition.
The outside mirror on the side
where you pressed the select switch
will tilt downward.
NOTE
When any of the following condition is
met, the outer mirrors return to their
normal positions.
The vehicle power is switched to a
position other than ON.
The shift selector lever is shifted to a
position other than R.
The select switch is pressed again.
Automatic glare prevention function
*
In conjunction with the glare
prevention function of the auto-type
rearview mirror, only the driver's side
outside mirror reduces the light from
the headlights of on-coming vehicles.
Operation Function After Vehicle
power is Switched OFF
The outside mirrors can be operated
for about 40 seconds after the vehicle
power is switched from ON to off with
all doors closed. If any door is opened,
the outside mirrors will stop operating.
Driving
Mirrors
5-10*Some models.
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Powe r Sw i tc h
Press the power switch to start/stop
the hybrid system or to switch the
vehicle power position (OFF/ACC/
ON).
Vehicle power position
OFF
All electrical accessories cannot be
used.
ACC
Some electrical accessories such as
audio can be used.
ON
All electrical accessories can be used.
Warning and Cautions forUsing the Power Switch
WARNING
Before leaving the driver's seat,
always switch the vehicle power off,
set the parking brake, and make sure
the selector lever is in the P position.
Leaving the driver's seat without
switching the vehicle power off, setting
the parking brake, and shifting the
selector lever to the P position is
dangerous. Unexpected vehicle
movement could occur which could
result in an accident. In addition, if
your intention is to leave the vehicle for
even a short period, it is important to
switch the vehicle power position to
OFF, as leaving it in another position
will disable some of the vehicle's
security systems and run the lead-acid
battery down.
Radio waves from the key may affect
medical devices such as pacemakers.
Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will affect
the device.
Other than for an emergency
situation, do not attempt to stop the
hybrid system while driving the
vehicle.
If the hybrid system is stopped while
driving the vehicle, loss of brake power
and power steering functions could
occur, making it difficult to control the
vehicle which could result in an
accident.
Driving
Po we r Sw i tc h
5-13
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

CAUTION
If the KEY warning light (red) is
displayed, or the power switch
indicator light (amber) flashes, this
could indicate a problem with the
hybrid starting system. This may
prevent the hybrid system from
starting or from switching the vehicle
power position to ACC or ON. Have
your vehicle inspected at an
Authorized Mazda Dealer as soon as
possible.
Refer to KEY Warning Light (Red) on
page 8-48.
 Before leaving the vehicle, make sure
that the vehicle power is switched
OFF.
How to Use the Power
Switch
The power switch starts/stops the
hybrid system and switches the vehicle
power position depending on the
vehicle status and the driver's
operation.
Starting the Hybrid system
1. Make sure that the parking brake isapplied.
2. Make sure that the selector lever is in the P position.
3. Depress the brake pedal. The power switch indicator light
(green) and the KEY indicator light
(green)
in the instrument
cluster turn on.
4.
The hybrid system starts and the
KEY indicator light (green)
in
the instrument cluster turns off.
The READY indicator light
in the instrument cluster turns on.
NOTE
Do not use high engine speeds until
reaching the operating temperature.
Driving
Power Switch
5-14
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

If an Accident Occurs
Heed the following cautions to prevent serious injury such as electric shock, or in the
worst case death.
WARNING
Do not continue to drive the vehicle.
To prevent further accidents, stop the vehicle in a safe place, shift the selector lever
to the P position, and then apply the parking brake to stop the hybrid system.
Never touch electrical wiring that may be protruding into or outside of the cabin.
Otherwise, it could result in electrical shock and serious injury.
Never touch any area where electrolyte is visible or electrolyte is leaking from the
area.
If electrolyte from the high voltage battery gets in the eyes or on the skin, it could
cause loss of vision or skin reactions. If electrolyte comes into contact with the eyes,
do not rub them, and after flushing with water for 15 minutes or longer, seek
medical attention immediately. In addition, if electrolyte comes into contact with
the skin, wash the areas with soap and wate r thoroughly. If you feel any abnormality
in your body, seek medical attention immediately.
Never approach objects that are on fire or extremely hot.
Electrolyte in the high voltage battery may cause a fire. If the vehicle catches fire,
extinguish the fire using a fire extinguisher (type ABC, BC, or C). Only extinguish a
fire with water when a large amount of water is available such as from a fire hydrant.
Using a small amount of water may cause the fire to spread.
Do not tow the vehicle with the front wheels or the rear wheels grounded.
Otherwise, the motor generates electricity which may cause a fire depending on the
condition of the damage. When towing the vehicle, tow it with all 4 wheels off the
ground.
Do not start the hybrid system if there is liquid leaking from the vehicle (other than
air conditioner water).
If liquid leakage (other than air conditioner water) is found on the road surface
under the vehicle, the fuel system may be damaged. Starting the hybrid system in
this condition, may cause a fire. Do not start the hybrid system and contact an
Authorized Mazda Dealer.
Scrapping Your Vehicle and Disposing of High Voltage Battery
The high voltage battery is collected to prevent accidents involving it. When
scrapping your vehicle, replacing the high voltage battery, or disposing of the high
voltage battery, consult an Authorized Mazda Dealer. Please cooperate in ensuring
that the vehicle's high voltage battery is collected.
Driving
e-SKYACTIV PHEV
5-21
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

WARNING
Appropriate disposal of the high voltage battery.
If the high voltage battery is not collected and disposed of appropriately, such as by
leaving it unattended or illegally abando ning it, some other person may touch it
which could cause electrocution leading to serious injury.
Fuel
CAUTION
 The e-SKYACTIV PHEV can be driven on electricity, but depending on the driving
conditions and mode, the vehicle will be driven using the engine and will need to
be refueled. Check the remaining amount of fuel and replenish the fuel if
necessary.
Refer to How to Use the Mazda intelligent Drive Select (Mi-Drive) on page 5-96.
 Depending on the vehicle usage conditions, fuel may remain in the tank for a long
period of time and the quality of the fuel may change. Refuel at least 25 L of fuel
every 12 months (total amount of refueling for 12 months is at least 25 L), as this
may affect parts of the fuel system and the engine.
 If the fuel has not been replenished for a certain period of time and the quality of
the fuel in the fuel tank is expected to change, a message is displayed in the
instrument cluster when the hybrid system is started. When a certain amount of
fuel is consumed, the message displayed in the instrument cluster is no longer
displayed.
Driving
e-SKYACTIV PHEV
5-22
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

How to Use the
e-SKYACTIV PHEV
Switching the Drive Mode
You can switch the drive mode of the
hybrid system by operating the switch.
TOWING mode/SPORT mode/
NORMAL mode/EV mode/
OFF-ROAD mode
Refer to How to Use the Mazda
intelligent Drive Select (Mi-Drive) on
page 5-96.
CHARGE Mode
The engine is used as a generator, and
the vehicle is driven while charging the
high voltage battery.
1. Start the hybrid system.
2.
When CHARGE mode is activated, the
CHARGE mode indicator light
in
the instrument cluster turns on.
Power is generated to the preset target
charge amount, and when the target
charge amount is reached, power is
generated to maintain it.
NOTE
Switching to CHARGE mode may not
be possible depending on the
conditions of the hybrid system.
When power consumption is high
due to the vehicle driving conditions,
outside air temperature, or when the
air conditioner is used, charging may
take longer than usual or may not
occur.
When the vehicle is driven while in
CHARGE mode, the engine operates
to generate electricity, therefore fuel
consumption may increase
compared to when driving the
vehicle in a mode other than
CHARGE mode.
If the vehicle power is switched OFF
while switching the mode to
CHARGE mode, the CHARGE mode
will be canceled the next time the
vehicle power is switched ON.
When pressing the charge mode
switch while the Mazda intelligent
Drive Select (Mi-Drive) is in EV
mode, the Mi-Drive switches to
NORMAL mode and the vehicle is
driven in CHARGE mode.
The mode may not be able to switch
to CHARGE mode when the fuel is
low.
The target charge amount can be
changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
Po we r Me te r
Displays in the instrument cluster while
driving in NORMAL mode or EV mode.
Driving
e-SKYACTIV PHEV
5-23
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

NORMAL mode
1. POWER gauge
2. CHARGE gauge
3. EV drive indicator light
4. Boost indicator light
5. CHARGE mode indicator light
EV mode
1. POWER gauge
2. CHARGE gauge
3. Boost indicator light
POWER gauge
Displays the energy used by the motor
or engine for driving. The higher the
output, the more the power meter
needle moves to the right. The more
the power meter needle moves to the
right, the easier it is to start the engine.
CHARGE gauge
Displays the energy charged in the high
voltage battery by regenerative braking.
The higher the charge, the more the
power meter needle moves
downward.
Boost indicator light
The light turns on when the energy
used for driving is at maximum output.
EV drive indicator light
The light turns on when the vehicle is
being driven using only the motor.
CHARGE mode indicator light
The light turns on when the vehicle is
being driven in CHARGE mode.
Approaching Vehicle Audible System
When the vehicle is driven at low
speeds, a warning sound is
automatically activated to warn that a
vehicle is approaching.
1. Start the hybrid system.
2. Shift the selector lever to a position other than P.
A warning sound is activated and stops
when the vehicle speed reaches 41
km/h (26 mph) or faster.
Driving
e-SKYACTIV PHEV
5-24
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Convenient Ways to Usethe e-SKYACTIV PHEV
Switch to Start in EV Mode
The hybrid system can be changed to
start in EV mode.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
Switching the Regenerative Braking
Strength
The regenerative braking strength can
be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
For Eco-Friendly and Economical
Driving
Using the Drive Mode
EV mode is mainly used in urban areas,
while NORMAL mode is used in
suburban areas and on expressways,
which leads to savings in electricity and
fuel consumption.
By actively using regenerative braking
to charge the high voltage battery, it is
possible to increase the EV travel
distance and to reduce fuel
consumption when driving the vehicle
in a mode other than EV mode.
To extend cruising distance
The electrical power consumption
while driving can be reduced and the
cruising distance can be extended by
doing the following operations.
With the charge connector
connected, turn on the climate
control system to provide a
comfortable temperature in the
cabin before driving.
When driving during cold
temperatures, use the seat warmer or
steering warmer instead of the
climate control system.
Adjust the climate control system to
a moderate airflow and temperature
setting.
Refrain from using the defogger
under conditions other than when a
window is fogged or frozen.
By maintaining a sufficient distance
between vehicles and using the
regenerative braking well, more
electrical power can be charged to
the high voltage battery.
To extend the life of the high voltage
battery
The high voltage battery life changes
depending on the vehicle storage
conditions or charging method.
To extend the life of the high voltage
battery, be careful of the following.
(Charging the battery)
Avoid unnecessary, frequent
charging.
Only charge the battery with as much
power as needed, and do not always
fully charge the battery. The
maximum charge limit can be set.
Refer to Convenient Ways to Use of
Charging on page 5-118.
(Parking the vehicle)
Do not park the vehicle in a place
where the ambient temperature is
extremely high or low.
Do not leave the vehicle while the
remaining high voltage battery power
is extremely low.
If the [Battery Cooling] operation notification is displayed on the
center display after driving the
vehicle, select [Activate].
Driving
e-SKYACTIV PHEV
5-25
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04