Oil MAZDA MODEL 2 2017 Owners Manual (in English)

2–15
Essential Safety Equipment
Seat Belt Systems
WARNING
Positioning the Shoulder Portion of the Seat Belt:
Improper positioning of the shoulder portion of the seat belt is dangerous. Always make
sure the shoulder portion of the seat belt is positioned across your shoulder and near
your neck, but never under your arm, on your neck, or on your upper arm.

Positioning the Lap Portion of the Seat Belt:
The lap portion of the seat belt worn too high is dangerous. In a collision, this would
concentrate the impact force directly on the abdominal area, causing serious injury.
Wear the lap portion of the belt snugly and as low as possible.

Instructions for Use of Seat Belt Assemblies:
Seatbelts are designed to bear upon the bony structure of the body, and should be worn
low across the front of the pelvis or the pelvis, chest and shoulders, as applicable;
wearing the lap section of the belt across the abdominal area must be avoided.
Seatbelts should be adjusted as ¿ rmly as possible, consistent with comfort, to provide
the protection for which they have been designed. A slack belt will greatly reduce the
protection afforded to the wearer.
Care should be taken to avoid contamination of the webbing with polishes, oils and
chemicals, and particularly battery acid. Cleaning may safely be carried out using mild
soap and water. The belt should be replaced if webbing becomes frayed, contaminated
or damaged.
It is essential to replace the entire assembly after it has been worn in a severe impact
even if damage to the assembly is not obvious.
Belts should not be worn with straps twisted.
Each belt assembly must only be used by one occupant; it is dangerous to put a belt
around a child being carried on the occupant's lap.
No modi¿ cations or additions should be made by the user which will either prevent
the seat belt adjusting devices from operating to remove slack, or prevent the seat belt
assembly from being adjusted to remove slack.

2–16
Essential Safety Equipment
Seat Belt Systems
CAUTION
Belt retraction may become dif¿ cult if the belts and rings are soiled, so try to keep them
clean. For more details about cleaning the seat belts, refer to "Seat Belt Maintenance"
(page 6-73 ).

Ring

Pregnant Women and Persons with Serious Medical Conditions
Pregnant women should always wear seat belts. Ask your doctor for speci¿ c
recommendations.
The lap belt should be worn SNUGLY AND AS LOW AS POSSIBLE OVER THE HIPS.
The shoulder belt should be worn across your shoulder properly, but never across the
stomach area.
Persons with serious medical conditions also should wear seat belts. Check with your doctor
for any special instructions regarding speci¿ c medical conditions.


Emergency Locking Mode
When the seat belt is fastened, it will always be in the emergency locking mode.
In the emergency locking mode, the belt remains comfortable on the occupant and the
retractor will lock in position during a collision.
If the belt is locked and cannot be pulled out, retract the belt once, and then try pulling it out
slowly. If this fails, pull the belt strongly one time and loosen, then pull it out again slowly.

3–44
Before Driving
Security System
*Some models.
Theft-Deterrent System *
If the theft-deterrent system detects an
inappropriate entry into the vehicle or
the intrusion sensor detects movement
in the vehicle which could result in the
vehicle (with the intrusion sensor) or its
contents being stolen, the alarm alerts the
surrounding area of an abnormality by
sounding the siren/horn and À ashing the
hazard warning lights.

The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Intrusion sensor
*
The intrusion sensor uses ultrasonic waves
to detect movement inside the vehicle and
to raise an alert of an intrusion into the
vehicle.

The intrusion sensor detects certain kinds
of movement inside the vehicle, however,
it may also respond to phenomenon
outside the vehicle such as vibrations, loud
noise, wind, and air currents.
CAUTION
In order for the intrusion sensor to
operate appropriately, be aware of the
following:
 
 Do not hang clothing or objects from
a head restraint or a coat hook.
  Return the extension sunvisors to
their original positions.
  Do not blind the intrusion sensor by
covering it or placing objects over it.
  Do not allow the intrusion sensor to
get soiled or wipe it with a liquid.
  Do not shock or cause an impact to
the intrusion sensor or the intrusion
sensor bezel.
  Do not install seats that are not
Mazda genuine products.
  To prevent obstruction of intrusion
sensor, do not place objects or cargo
near the intrusion sensor that are
higher than the head restraints.

Intrusion sensor and
intrusion sensor bezel

3–51
Before Driving
Driving Tips
Rocking the Vehicle
WARNING
Do not spin the wheels at high speed,
and do not allow anyone to stand
behind a wheel when pushing the
vehicle:
When the vehicle is stuck, spinning
the wheels at high speed is dangerous.
The spinning tyre could overheat and
explode. This could cause serious
injuries.
CAUTION
Too much rocking may cause engine
overheating, transaxle failure, and tyre
damage.
If you must rock the vehicle to free it from
snow, sand or mud, depress the accelerator
slightly and slowly move the shift lever
from 1 (D) to R.
Winter Driving
Carry emergency gear, including tyre
chains, window scraper, À ares, a small
shovel, jumper leads, and a small bag of
sand or salt.
Ask an expert repairer, we recommend an
Authorised Mazda Repairer to check the
following:
 


 Have the proper ratio of antifreeze in the
radiator.
  Refer to Engine Coolant on page
6-29 .
 


 Inspect the battery and its leads. Cold
reduces battery capacity.
 


 Use an engine oil appropriate for the
lowest ambient temperatures that the
vehicle will be driven in (page 6-23 ).




 Inspect the ignition system for damage
and loose connections.
 


 Use washer À uid made with antifreeze—
but do not use engine coolant antifreeze
for washer À uid (page 6-32 ).

3–55
Before Driving
Driving Tips
Turbocharger Information (SKYACTIV-D 1.5)
CAUTION
  After driving at freeway speeds or up a long hill, idle the engine at least 30 seconds
before stopping it. Otherwise, the turbocharger could be damaged. However, when
i-stop operates, idling is unnecessary.
  Racing or over-revving the engine, particularly after it's just been started, can damage
the turbocharger.
  To protect the engine from damage, the engine is designed so that it cannot be raced
just after starting it in extremely cold weather.
The turbocharger greatly enhances engine power. Its advanced design provides improved
operation and requires minimum maintenance.

To get the most from it, observe the following.

1. Change engine oil and ¿ lter according to Scheduled Maintenance (page 6-3 ).
2. Use only recommended engine oil (page 6-23 ). Extra additives are NOT
recommended.

4–38
When Driving
Instrument Cluster and Display
Warning/Indicator Lights
Instrument Cluster varies depending on model and speci¿ cations.

Type A
Type B
Type C (Digital Speed Meter Type)
(Analog Speed Meter Type (With Tachometer))
(Analog Speed Meter Type (Without Tachometer)) Instrument Cluster

Warning Lights
These lights turn on or À ash to notify the user of the system operation status or a system
malfunction.

Signal Warning Page

Brake System Warning Light *1*2 7-35

ABS Warning Light *1 Electronic Brake
Force Distribution
System Warning
7-35
ABS warning
7-38

Charging System Warning Light *1 7-35

Engine Oil Warning Light *1 7-35

4–44
When Driving
Instrument Cluster and Display
*Some models.
Wrench Indicator Light

When the ignition is switched ON, the
wrench indicator light turns on and then
turns off after a few seconds.

The wrench indicator light turns on
when the preset maintenance period
arrives. Verify the content and perform
maintenance.
Refer to Maintenance Monitor on page
6-15 .
SKYACTIV-D 1.5
The wrench indicator light turns on under
the following conditions:
 


 The engine oil has deteriorated.



 The engine oil level is around the MIN
mark on the dipstick or it is less than the
MIN mark.
*  


 The engine oil level is around the X
mark on the dipstick or it exceeds the X
mark.
*
Check the engine oil. Refer to Inspecting
Engine Oil Level on page 6-28 .
Replace the engine oil if the wrench
indicator light does not turn off even
though the engine oil level is in the normal
range.
NOTE
  Depending on the vehicle use
conditions, the wrench indicator light
may turn on for reasons other than
the preset maintenance period.
  Whenever the engine oil is replaced,
a reset of the vehicle engine control
unit is necessary.
 Your Authorised Mazda Repairer
will be able to reset the engine
control unit or see page 6-27 for
the Vehicle engine control unit reset
procedure.
Low Engine Coolant Temperature
Indicator Light (Blue)

The light illuminates continuously when
the engine coolant temperature is low and
turns off after the engine is warm.
If the low engine coolant temperature
indicator light remains illuminated after
the engine has been suf¿ ciently warmed
up, the temperature sensor could have a
malfunction. Consult an expert repairer,
we recommend an Authorised Mazda
Repairer.

4–157
When Driving
i-ACTIVSENSE
WARNING
Turn off the Smart City Brake Support (SCBS) when the vehicle is running on a chassis
roller or being towed:
Turn off the Smart City Brake Support (SCBS) system to prevent mistaken operation
when the vehicle is running on a chassis roller or being towed.
Refer to the Stopping the Smart City Brake Support (SCBS) System Operation on page
4-160 on how to turn off the Smart City Brake Support (SCBS) system.
CAUTION
  When driving off-road in areas where there is grass or forage, it is recommended that
the Smart City Brake Support (SCBS) system be turned off.
  Always use tyres for all wheels that are of the speci¿ ed size, and the same
manufacturer, brand, and tread pattern. In addition, do not use tyres with signi¿ cantly
different wear patterns on the same vehicle as the Smart City Brake Support (SCBS)
system may not operate normally.
  The laser sensor includes a function for detecting a soiled windscreen and informing
the driver, however, depending on the conditions, it may not detect plastic shopping
bags, ice or snow on the windscreen. In such cases, the system cannot accurately
determine a vehicle ahead and may not be able to operate normally. Always drive
carefully and pay attention to the road ahead.

4–173
When Driving
i-ACTIVSENSE
CAUTION
  The Forward Sensing Camera (FSC) includes a function for detecting a soiled
windscreen and informing the driver, however, depending on the conditions, it may not
detect plastic shopping bags, ice or snow on the windscreen. In such cases, the system
cannot accurately determine a vehicle ahead and may not be able to operate normally.
Always drive carefully and pay attention to the road ahead.
NOTE
  In the following cases, the Forward Sensing Camera (FSC) cannot detect target objects
correctly, and each system may be unable to operate normally.
 


 The height of the vehicle ahead is low.



 You drive your vehicle at the same speed as the vehicle ahead.



 Headlights are not turned on during the night or when going through a tunnel.

4–17 7
When Driving
i-ACTIVSENSE
CAUTION
Heed the following precautions to assure correct operation of each system.  
 Do not adhere stickers (including transparent stickers) to the surface of the radiator
grille and front emblem in and around the radar sensor (front), and do not replace
the radiator grille and front emblem with any product that is not a genuine product
designed for use with the radar sensor (front).
  The radar sensor (front) includes a function for detecting soiling of the radar sensor's
front surface and informing the driver, however, depending on the conditions, it may
require time to detect or it may not detect plastic shopping bags, ice or snow. If this
occurs, the system may not operate correctly, therefore always keep the radar sensor
(front) clean.
  Do not install a grille guard. 
 If the front part of the vehicle has been damaged in a vehicle accident, the position of
the radar sensor (front) may have moved. Stop the system immediately and always
have the vehicle inspected at an Authorised Mazda Repairer.
  Do not use the front bumper to push other vehicles or obstructions such as when
pulling out of a parking space. Otherwise, the radar sensor (front) could be hit and its
position deviated.
  Do not remove, disassemble, or modify the radar sensor (front). 
 For repairs, replacement or paint work around the radar sensor (front), consult an
Authorised Mazda Repairer.
  Do not modify the suspension. If the suspension are modi¿ ed, the vehicle's posture
could change and the radar sensor (front) may not be able to correctly detect a vehicle
ahead or an obstruction.