heating MAZDA MODEL 2 2017 Owners Manual (in English)

3–30
Before Driving
Fuel and Emission
Engine Exhaust (Carbon monoxide)
WARNING
Do not drive your vehicle if you smell exhaust gas inside the vehicle:
Engine exhaust gas is dangerous. This gas contains carbon monoxide (CO), which is
colourless, odourless, and poisonous. When inhaled, it can cause loss of consciousness
and death. If you smell exhaust gas inside the vehicle, keep all windows fully open and
contact an expert repairer, we recommend an Authorised Mazda Repairer immediately.

Do not run the engine when inside an enclosed area:
Running the engine inside an enclosed area, such as a garage, is dangerous. Exhaust
gas, which contains poisonous carbon monoxide, could easily enter the cabin. Loss of
consciousness or even death could occur.

Open the windows or adjust the heating or cooling system to draw fresh air when idling
the engine:
Exhaust gas is dangerous. When the vehicle is stopped with the windows closed and
the engine running for a long time even in an open area, exhaust gas, which contains
poisonous carbon monoxide, could enter the cabin. Loss of consciousness or even death
could occur.

Clear snow from underneath and around your vehicle, particularly the tail pipe, before
starting the engine:
Running the engine when a vehicle is stopped in deep snow is dangerous. The exhaust
pipe could be blocked by the snow, allowing exhaust gas to enter the cabin. Because
exhaust gas contains poisonous carbon monoxide, it could cause loss of consciousness
or even death to occupants in the cabin.

3–51
Before Driving
Driving Tips
Rocking the Vehicle
WARNING
Do not spin the wheels at high speed,
and do not allow anyone to stand
behind a wheel when pushing the
vehicle:
When the vehicle is stuck, spinning
the wheels at high speed is dangerous.
The spinning tyre could overheat and
explode. This could cause serious
injuries.
CAUTION
Too much rocking may cause engine
overheating, transaxle failure, and tyre
damage.
If you must rock the vehicle to free it from
snow, sand or mud, depress the accelerator
slightly and slowly move the shift lever
from 1 (D) to R.
Winter Driving
Carry emergency gear, including tyre
chains, window scraper, À ares, a small
shovel, jumper leads, and a small bag of
sand or salt.
Ask an expert repairer, we recommend an
Authorised Mazda Repairer to check the
following:
 


 Have the proper ratio of antifreeze in the
radiator.
  Refer to Engine Coolant on page
6-29 .
 


 Inspect the battery and its leads. Cold
reduces battery capacity.
 


 Use an engine oil appropriate for the
lowest ambient temperatures that the
vehicle will be driven in (page 6-23 ).




 Inspect the ignition system for damage
and loose connections.
 


 Use washer À uid made with antifreeze—
but do not use engine coolant antifreeze
for washer À uid (page 6-32 ).

3–63
Before Driving
Towing
Trailer Towing Tips
Before driving
 




 Verify that your Mazda maintains a near-normal attitude when a loaded or unloaded trailer
is connected. Do not drive if it has an abnormal front-up or front-down position. Inspect
for incorrect nose weight, worn suspension parts, and trailer overloading. Have the vehicle
inspected by an expert repairer, we recommend an Authorised Mazda Repairer.
 


 Make sure the trailer cargo is secure to prevent it from shifting.



 Make sure the mirrors meet all government regulations. Inspect them.



 Before starting out, inspect the operation of all vehicle and trailer lights and all vehicle-
to-trailer connections. Stop and re-inspect all lights and connections after driving a short
distance.

Driving
 




 Your Mazda will handle differently with a trailer in tow, so practice turning, backing, and
stopping in a traf¿ c-free area.




 Take time to get accustomed to the extra weight and length.



 Do not exceed 100 km/h (62 mph) with a trailer in tow. If the local legal maximum speed
with a trailer in tow is less than 100 km/h (62 mph), do not exceed the legal speed.
CAUTION
If the vehicle exceeds 100 km/h (62 mph) with a trailer in tow, the vehicle could be
damaged.
 


 When ascending a hill, shift into a lower gear to reduce the possibility of overloading or
overheating the engine, or both.
 


 When descending a hill, shift into a lower gear and use engine compression as a braking
effect. Pay constant attention to speed and use the brakes only as needed. Holding the
brake pedal down for a prolonged period may cause the brakes to overheat and lose
power.

4–14
When Driving
Start/Stop Engine
Automatic transaxle
1. Engine idling stops when the brake pedal is depressed while the vehicle is driven (except
for driving in the R or M position second gear ¿ xed mode) and the vehicle is stopped.
2. The engine restarts automatically when the brake pedal is released with the selector lever
in the D or M position (not in second gear ¿ xed mode).
3. If the selector lever is in the N or P position, the engine does not restart when the brake
pedal is released. The engine restarts when the brake pedal is depressed again or the
selector lever is shifted to the D, M (not in second gear ¿ xed mode) or the R position.
(For the purposes of safety, always keep the brake pedal depressed when shifting the
selector lever while engine idling is stopped.)

Operation conditions
When the system is operable
Under the following conditions, engine idling stops and the i-stop indicator light (green)
turns on.
 


 (SKYACTIV-G 1.3, SKYACTIV-G 1.5) 
 The engine is warmed up.



 (SKYACTIV-D 1.5) 


 
 The engine is not cold.


 
 The fuel injection amount learning, which is performed periodically and automatically,
is not being performed.
 


 The engine has been started and the vehicle is driven for a certain period.



 The engine is started with the bonnet closed.



 The battery is in good condition.



 All doors, liftgate/boot lid, and bonnet are closed.



 The driver's seat belt is fastened.



 The air conditioner is not operating with the airÀ ow mode dial in the position.



 (Automatic air-conditioning) 


 
 The temperature setting dial for the air-conditioning is set to a position other than
maximum heating/maximum cooling (A/C ON).
 

 
 The vehicle's interior temperature and the set temperature for the air conditioner are
nearly the same.
 


 The i-stop warning light (amber) is not turned on/À ashing.



 The keyless entry & push button start system functions are normal.



 The brake vacuum is suf¿ ciently high.



 The steering wheel is not being operated.

4–15
When Driving
Start/Stop Engine
 


 (Manual transaxle) 


 
 The vehicle speed is 3 km/h (1.8 mph) or less.


 
 The shift lever is in the neutral position.


 
 The clutch pedal is not depressed. 



 (Automatic transaxle) 


 
 The vehicle is stopped.


 
 The selector lever is in the D or M position (not in second gear ¿ xed mode).


 
 The automatic transaxle À uid has warmed up suf¿ ciently.


 
 The automatic transaxle À uid temperature is not abnormally high.


 
 The steering wheel is almost in the straight-ahead position (idling may not stop even
with the steering wheel in the straight-ahead position if force is applied to the steering
wheel. Release the force applied to the steering wheel to stop engine idling).
 

 
 The vehicle is stopped by depressing the brake pedal.


 
 Emergency braking is not applied.

When the system is not operable
Engine idling does not stop in the following conditions:
 


 The vehicle is stopped but the engine is kept idling.



 The air conditioner is operating with the airÀ ow mode dial in the position.



 (Automatic air-conditioning) 


 
 The temperature setting dial for the air-conditioning is set to the maximum heating/
maximum cooling (A/C ON) position.
 

 
 There is a large difference between the cabin temperature and the set temperature of the
air conditioner.
 


 The ambient temperature is extremely high or low.



 The atmospheric pressure is low (when driving at high altitudes).



 (Automatic transaxle) 


 
 The vehicle is stopped on a steep incline.


 
 The steering wheel is not in the straight-ahead position while the vehicle is stopped. 



 (SKYACTIV-D 1.5) 


 
 The particulate matter (PM) is being removed by the diesel particulate ¿ lter (DPF).


 
 The fuel injection amount learning is being performed. (The i-stop indicator light (green)
turns off when the vehicle speed before stopping is approx. 10 km/h (6.2 mph) or less
and fuel injection amount learning is performed while the vehicle is stopped.)

4–17
When Driving
Start/Stop Engine
NOTE

Engine restarts automatically while engine idling is stopped
Under the following conditions, the engine restarts automatically.
 
 The i-stop OFF switch is pressed until the beep sounds.

 The air conditioner is operated with the airÀ ow mode dial in the position. 
 (Automatic air-conditioning) 



 The temperature setting dial of the air conditioner is set to the maximum heating/
maximum cooling (A/C ON).
 


 The cabin temperature is largely different from the set temperature of the air
conditioner.
 
 The brakes are released slightly on a slope and the vehicle begins to move. 
 Two minutes have elapsed since the idling was stopped. 
 The battery power is depleted. 
 (Automatic transaxle) 



 The accelerator pedal is depressed with the selector lever in the D or M (not in
second gear ¿ xed mode) position.




 The selector lever is shifted to the R position.



 The selector lever is shifted from N or P position to D or M (not in second gear ¿ xed
mode) position.
 


 The steering wheel is operated with the selector lever in the D or M (not in second
gear ¿ xed mode) position.




 The selector lever is in the M position and the second gear ¿ xed mode is selected. 

 (Except European model) 



 (Manual transaxle) 
 With the shift lever in the neutral position, the driver's seat belt is unfastened and the
driver's door is opened.
 


 (Automatic transaxle)
With the selector lever in the N or P position, the driver's seat belt is unfastened and
the driver's door is opened.

4–60
When Driving
Automatic Transaxle
Driving Tips
WARNING
Do not let the vehicle move in a
direction opposite to the direction
selected by the selector lever:
Do not let the vehicle move backward
with the selector lever in a forward
position, or do not let the vehicle move
forward with the selector lever in the
reverse position. Otherwise, the engine
may stop, causing the loss of the power
brake and power steering functions,
and make it dif¿ cult to control the
vehicle which could result in an
accident.
Passing
For extra power when passing another
vehicle or climbing steep grades, depress
the accelerator fully. The transaxle will
shift to a lower gear, depending on vehicle
speed.
NOTE
  The accelerator pedal may initially
feel heavy as it is being depressed,
then feel lighter as it is depressed
further. This change in pedal force
aids the engine control system
in determining how much the
accelerator pedal has been depressed
for performing kickdown, and
functions to control whether or not
kickdown should be performed.
 
 While the selector lever is in the M
position and the DSC is turned off,
manual shift mode does not switch
to automatic shift mode even if
the accelerator pedal is completely
depressed. Operate the selector lever.
Climbing steep grades from a stop
To climb a steep grade from a stopped
position:

1. Depress the brake pedal.
2. Shift to D or M1, depending on the
load weight and grade steepness.
3. Release the brake pedal while gradually
accelerating.

Descending steep grades
When descending a steep grade, shift to
lower gears, depending on load weight and
grade steepness. Descend slowly, using the
brakes only occasionally to prevent them
from overheating.

5–10
Interior Features
Air-Conditioning System
*Some models.
WARNING
Do not use the recirculated air position
in cold or rainy weather:
Using the recirculated air position in
cold or rainy weather is dangerous as it
will cause the windows to fog up. Your
vision will be hampered, which could
lead to a serious accident.
Air intake selector (Type C/Type D)
This lever controls the source of air
entering the vehicle.

It is recommended that under normal
conditions the switch be kept in the
outside air position.
Recirculated air position (
)
Outside air is shut off. Air within the
vehicle is recirculated.
Outside air position (
)
(Type C)
Outside air is taken into the vehicle. Use
this position for normal ventilation and
heating.
(Type D)
Outside air is taken into the vehicle. Use
this position for normal ventilation.
WARNING
Do not use the position in cold or
rainy weather:
Using the
position in cold or rainy
weather is dangerous as it will cause
the windows to fog up. Your vision will
be hampered, which could lead to a
serious accident.
Rear window defogger switch
Press the rear window defogger switch to
defrost the rear window.
Refer to Rear Window Defogger on page
4-78 .
Heating *
1. Set the mode selector dial to the
position.
2. (Type A/Type B)
Set the air intake selector to the outside
air position.
(Type C)
Set the air intake selector to the

position.
3. Set the temperature control dial to the
hot position.
4. Set the fan control dial to the desired
speed.
5. (Type A/Type C)
If dehumidi¿ ed heating is desired, turn
on the air conditioner.

NOTE
  If the windscreen fogs up easily, set
the mode selector dial to the

position.
  (Type A/Type C)  If cooler air is desired at face level,
set the mode selector dial to the

position and adjust the temperature
control dial to maintain maximum
comfort.
  The air to the À oor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).

5–11
Interior Features
Air-Conditioning System
Cooling (With air conditioner)
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
cold position.
3. Set the fan control dial to the desired
speed.
4. Turn on the air conditioner by pressing
the A/C switch.
5. After cooling begins, adjust the fan
control dial and temperature control
dial as needed to maintain maximum
comfort.

CAUTION
If the air conditioner is used while
driving up long hills or in heavy traf¿ c,
monitor the engine coolant temperature
warning light to see if it is illuminated or
À ashing (page 4-38 ).
The air conditioner may cause engine
overheating. If the warning light is
illuminated or À ashing, turn the air-
conditioning off (page 7-29 ).
NOTE
  (Type A/Type B)  When maximum cooling is desired,
set the temperature control dial to
the extreme cold position and set the
air intake selector to the recirculated
air position, then turn the fan control
dial fully clockwise.
  (Type C/Type D)  When maximum cooling is desired,
set the temperature control dial to the
extreme cold position and set the air
intake selector to the recirculated air
position, then set the fan control dial
to position 4.
  (Type A/Type C)  If warmer air is desired at À oor level,
set the mode selector dial to the

position and adjust the temperature
control dial to maintain maximum
comfort.
  The air to the À oor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).

5–12
Interior Features
Air-Conditioning System
Ventilation
1. Set the mode selector dial to the
position.
2. (Type A/Type B)
Set the air intake selector to the outside
air position.
(Type C/Type D)
Set the air intake selector to the

position.
3. Set the temperature control dial to the
desired position.
4. Set the fan control dial to the desired
speed.

Windscreen Defrosting and
Defogging
1. Set the mode selector dial to the
position.
2. (Type C/Type D)
Set the air intake selector to the

position.
3. Set the temperature control dial to the
desired position.
4. Set the fan control dial to the desired
speed.
5. (Type A/Type C)
If dehumidi¿ ed heating is desired, turn
on the air conditioner.
(Type D)
Press the A/C switch to turn on the air
conditioner.

WARNING
Do not defog the windscreen using the
position with the temperature
control set to the cold position (Type A/
Type B/Type C):
Using the
position with the
temperature control set to the cold
position is dangerous as it will cause
the outside of the windscreen to fog up.
Your vision will be hampered, which
could lead to a serious accident. Set the
temperature control to the hot or warm
position when using the
position.

Do not leave the air conditioner in the
position with the temperature
control set to cold after the windscreen
has defogged (Type D):
Leaving the air conditioner in the

position with the temperature control
set to cold after the windscreen has
defogged is dangerous as the outside of
the windscreen will fog up. Your vision
will be hampered, which could lead to a
serious accident.
Set the mode selector dial except the

position and turn on the windscreen
wipers to clear the window.