change wheel MAZDA MODEL 2 2019 Owners Manual (in English)

Page 86 of 759

x(With the i-stop function (European
models))
Removing the key from the vehicle,
closing all the doors and pressing the
LOCK button on the key while the i-stop
function is operating (engine is stopped)
will switch the ignition OFF and lock all
the doors (Steering wheel also locks).
Refer to i-stop on page 4-12.
xMake sure all doors and the liftgate/boot
lid are locked after pressing the button.
x(With double locking system)
Pressing the lock button twice within
three seconds will activate the double
locking system.
Refer to Double Locking System on page
3-12.
x(With theft-deterrent system)
When the doors are locked by pressing
the lock button on the key while the
theft-deterrent system is armed, the
hazard warning lights will flash once to
indicate that the system is armed.
8QORFNEXWWRQ
7RXQORFNWKHGRRUVDQGWKHOLIWJDWHERRW
OLGSUHVVWKHXQORFNEXWWRQDQGWKHKD]DUG
ZDUQLQJOLJKWVZLOOIODVKWZLFH
:LWKWKHDGYDQFHGNH\OHVVIXQFWLRQ
([FHSW(XURSHDQPRGHOV
$EHHSVRXQGZLOOEHKHDUGWZLFH
NOTE
x(Auto re-lock function)
After unlocking with the key, all doors
and the liftgate/boot lid will
automatically lock if any of the
following operations are not performed
within about 30 seconds. If your vehicle
has a theft-deterrent system, the hazard
warning lights will flash for
confirmation.
The time required for the doors to lock
automatically can be changed.
Refer to Personalisation Features on
page 9-15.
xA door or the liftgate/boot lid is
opened.
xThe ignition is switched to any
position other than off.
x(With theft-deterrent system)
When the doors are unlocked by
pressing the unlock button on the key
while the theft-deterrent system is turned
off, the hazard warning lights will flash
twice to indicate that the system is
turned off.
%HIRUH'ULYLQJ
.H\V


Page 126 of 759

+D]DUGRXV'ULYLQJ
:$ 5 1 , 1 *
Be extremely careful if it is necessary to
downshift on slippery surfaces:
Downshifting into lower gear while driving
on slippery surfaces is dangerous. The
sudden change in tyre speed could cause
the tyres to skid. This could lead to loss of
vehicle control and an accident.
:KHQGULYLQJRQLFHRULQZDWHUVQRZ
PXGVDQGRUVLPLODUKD]DUGV
x%HFDXWLRXVDQGDOORZH[WUDGLVWDQFHIRU
EUDNLQJ
x$YRLGVXGGHQEUDNLQJDQGVXGGHQ
PDQRHXYULQJ
x'RQRWSXPSWKHEUDNHV&RQWLQXHWR
SUHVVGRZQRQWKHEUDNHSHGDO
5HIHUWR$QWLORFN%UDNH6\VWHP $%6
RQSDJH
x,I\RXJHWVWXFNVHOHFWDORZHUJHDUDQG
DFFHOHUDWHVORZO\'RQRWVSLQWKHIURQW
ZKHHOV
x)RUPRUHWUDFWLRQLQVWDUWLQJRQVOLSSHU\
VXUIDFHVVXFKDVLFHRUSDFNHGVQRZXVH
VDQGURFNVDOWFKDLQVFDUSHWLQJRU
RWKHUQRQVOLSPDWHULDOXQGHUWKHIURQW
ZKHHOV
NOTE
Use snow chains only on the front wheels.
)ORRU0DW
:HUHFRPPHQGWKHXVHRI*HQXLQH
0D]GDIORRUPDWV
:$ 5 1 , 1 *
Make sure the floor mats are secured with
the grommets or the retainers to prevent
them from bunching up under the foot
pedals (Driver's side):
Using a
floor mat that is not secured is
dangerous as it will interfere with the
accelerator and brake pedal operation
(driver's side), which could result in an
accident.
Only use a
floor mat which conforms to the
shape of the floor on the driver's side and
make sure it is oriented correctly.
Secure the floor mat using the grommets or
retainers.
There are various ways to secure floor mats
depending on the type used, therefore
secure the mat according to the type.
After installing the floor mat, make sure
that it does not slide from side to side or
back and forth, and that there is sufficient
clearance with the accelerator and brake
pedals on the driver's side.
After removing the floor mat for cleaning
or some other reason, always securely
reinstall it while paying attention to the
precautions just mentioned.
%HIRUH'ULYLQJ
'ULYLQJ7LSV


Page 197 of 759

8VLQJVWHHULQJVKLIWVZLWFK
7RVKLIWGRZQWRDORZHUJHDUZLWKWKH
VWHHULQJVKLIWVZLWFKHVSXOOWKH'2:1
VZLWFK
WRZDUG\RXRQFHZLWK\RXU
ILQJHUV

DOWN switch (-)
:$ 5 1 , 1 *
Do not use engine braking on slippery road
surfaces or at high speeds:
Shifting down while driving on wet, snowy,
or frozen roads, or while driving at high
speeds causes sudden engine braking,
which is dangerous. The sudden change in
tyre speed could cause the tyres to skid.
This could lead to loss of vehicle control
and an accident.
Keep your hands on the steering wheel rim
when using fingers on the steering shift
switches:
Putting your hands inside the rim of the
steering wheel when using the steering
shift switches is dangerous. If the driver's
air bag were to deploy in a collision, your
hands could be impacted causing injury.
NOTE
xWhen driving at high speeds, the gear
may not shift down.
xDuring deceleration, the gear may
automatically shift down depending on
vehicle speed.
xWhen depressing the accelerator fully,
the transaxle will shift to a lower gear,
depending on vehicle speed. However,
the gears do not kickdown while the
DSC is turned off.
▼▼6HFRQG*HDU)L[HG0RGH
:KHQWKHVHOHFWRUOHYHULVPRYHGEDFN
ZKLOHWKHYHKLFOHVSHHGLVDERXWNPK
PSK RUOHVVWKHWUDQVD[OHLVVHWLQWKH
VHFRQGJHDUIL[HGPRGH7KHJHDULVIL[HG
LQVHFRQGZKLOHLQWKLVPRGHIRUHDVLHU
DFFHOHUDWLRQIURPDVWRSDQGGULYLQJRQ
VOLSSHU\URDGVVXFKDVVQRZFRYHUHG
URDGV
,IWKHVHOHFWRUOHYHULVPRYHGEDFN
RU
IRUZDUG
ZKLOHLQWKHVHFRQGJHDUIL[HG
PRGHWKHPRGHZLOOEHFDQFHOOHG
:KHQ'ULYLQJ
$XWRPDWLF7UDQVD[OH

6RPHPRGHOV

Page 224 of 759

'\QDPLF6WDELOLW\&RQWURO
'6&

7KH'\QDPLF6WDELOLW\&RQWURO '6&
DXWRPDWLFDOO\FRQWUROVEUDNLQJDQGHQJLQH
WRUTXHLQFRQMXQFWLRQZLWKV\VWHPVVXFKDV
$%6DQG7&6WRKHOSFRQWUROVLGHVOLS
ZKHQGULYLQJRQVOLSSHU\VXUIDFHVRU
GXULQJVXGGHQRUHYDVLYHPDQRHXYULQJ
HQKDQFLQJYHKLFOHVDIHW\

5HIHUWR$%6 SDJH DQG7&6 SDJH
 

'6&RSHUDWLRQLVSRVVLEOHDWVSHHGV
JUHDWHUWKDQNPK PSK 

7KHZDUQLQJOLJKWWXUQVRQZKHQWKH
V\VWHPKDVDPDOIXQFWLRQ
5HIHUWR&RQWDFW$XWKRULVHG0D]GD
5HSDLUHUDQG+DYH9HKLFOH,QVSHFWHGRQ
SDJH
:$ 5 1 , 1 *
Do not rely on the Dynamic Stability
Control as a substitute for safe driving:
The Dynamic Stability Control (DSC)
cannot compensate for unsafe and reckless
driving, excessive speed, tailgating
(following another vehicle too closely), and
hydroplaning (reduced tyre friction and
road contact because of water on the road
surface). You can still have an accident.
&$87,21
¾The DSC may not operate correctly
unless the following are observed:
¾Use tyres of the correct size
specified
for your Mazda on all 4 wheels.
¾Use tyres of the same manufacturer,
brand and tread pattern on all 4
wheels.
¾Do not mix worn tyres.
¾The DSC may not operate correctly when
tyre chains are used or a temporary spare
tyre is installed because the tyre diameter
changes.
▼7&6'6&,QGLFDWRU/LJKW
7KLVLQGLFDWRUOLJKWVWD\VRQIRUDIHZ
VHFRQGVZKHQWKHLJQLWLRQLVVZLWFKHG21
,IWKH7&6RU'6&LVRSHUDWLQJWKH
LQGLFDWRUOLJKWIODVKHV

,IWKHOLJKWVWD\VRQWKH7&6'6&RUWKH
EUDNHDVVLVWV\VWHPPD\KDYHD
PDOIXQFWLRQDQGWKH\PD\QRWRSHUDWH
FRUUHFWO\7DNH\RXUYHKLFOHWRDQH[SHUW
UHSDLUHU ZHUHFRPPHQGDQ$XWKRULVHG
0D]GD5HSDLUHU 
:KHQ'ULYLQJ
$%67&6'6&

6RPHPRGHOV

Page 249 of 759

:$ 5 1 , 1 *
Do not use the LDWS under the following conditions:
The system may not operate adequately according to the actual driving conditions, resulting
in an accident.
¾Driving on roads with tight curves.
¾Driving under bad weather conditions (rain, fog, and snow).
The functions of the LDWS have limitations:
Always stay on course using the steering wheel and drive with care. The system is not
designed to compensate for a driver’s lack of caution and if you rely too much on the LDWS it
could lead to an accident. The driver is responsible for assuring lane changes and other
manoeuvres. Always pay attention to the direction in which the vehicle is travelling and the
vehicle’s surroundings.
&$87,21
Do not modify the suspension. If the vehicle height or the damping force of the suspensions is
changed, the LDWS may not operate correctly.
NOTE
xIf your vehicle deviates from its traffic lane, the LDWS operates (warning sound and
indicator light). Steer the vehicle adequately to drive the vehicle to the centre of the lane.
xWhen the direction indicator lever is operated for a lane change, the LDWS warning is
automatically cancelled. The LDWS warning becomes operable when the direction
indicator lever is returned and the system detects the white or yellow lines.
xIf the steering wheel, accelerator pedal, or brake pedal is operated abruptly and the
vehicle moves close to a white or yellow line, the system determines that the driver is
making a lane change and the LDWS warning is automatically cancelled.
xThe LDWS may not operate during the period immediately after the vehicle has deviated
from its lane and the LDWS has operated, or the vehicle deviates from its lane repeatedly
within a short period of time.
xThe LDWS does not operate if it does not detect the white or yellow lines of the traffic
lane.
:KHQ'ULYLQJ
L$&7,96(16(


Page 276 of 759

xThe following are not detected as physical objects.
xVehicles approaching in the opposite direction
xPedestrians
xStationary objects (stopped vehicles, obstructions)
xIf a vehicle ahead is travelling at an extremely low speed, the system may not detect it
correctly.
xDuring headway control travel, do not set the system on two-wheeled vehicles such as
motorcycles and bicycles.
xDo not use the MRCC system under conditions in which the close proximity warnings are
frequently activated.
xDuring headway control travel, the system accelerates and decelerates your vehicle in
conjunction with the speed of the vehicle ahead. However, if it is necessary to accelerate
for a lane change or if the vehicle ahead brakes suddenly causing you to close in on the
vehicle rapidly, accelerate using the accelerator pedal or decelerate using the brake
pedal depending on the conditions.
xWhile the MRCC system is in use, it does not cancel even if the selector lever (automatic
transaxle)/shift lever (manual transaxle) is operated and any intended engine braking will
not occur. If deceleration is required, lower the vehicle speed setting or depress the brake
pedal.
xThe brake lights are illuminated while the MRCC automatic braking is operating,
however, they may not be illuminated while the vehicle is on a down slope at the set
vehicle speed or travelling at a constant speed and following a vehicle ahead.
xThe MRCC warning light (amber) illuminates when the system has a malfunction.
Refer to Warning Lights on page 4-39.
xThe headway control operation can be cancelled and the system can be switched to only
cruise control.
Refer to Cruise Control Function on page 4-143.
▼0D]GD5DGDU&UXLVH&RQWURO 05&& 'LVSOD\,QGLFDWLRQ
7KHVHWWLQJVWDWXVDQGRSHUDWLRQFRQGLWLRQVRIWKH05&&V\VWHPDUHLQGLFDWHGLQWKHDFWLYH
GULYLQJGLVSOD\
Vehicle ahead display
MRCC Distance
between vehicle
display
MRCC Set vehicle speed
:KHQ'ULYLQJ
L$&7,96(16(


Page 287 of 759

¾The tyre pressures are not adjusted to the
specified pressure.
¾Tyres of a different specified size are used, such as an emergency spare tyre.
&$87,21
Heed the following cautions so that the LAS & LDWS can operate normally.
¾Do not modify the suspensions.
¾Always use wheels of the
specified type and size for the front and rear wheels. Consult an
expert repairer (we recommend an Authorised Mazda Repairer) for tyre replacement.
NOTE
xWhen the direction indicator lever is operated for a lane change, the LAS & LDWS is
automatically disabled. The LAS & LDWS becomes operational again when the direction
indicator lever is returned and the system detects white (yellow) lane lines while the
vehicle is being driven normally within its vehicle lane.
xIf the steering wheel, accelerator pedal, or brake pedal is operated abruptly and the
vehicle moves close to a white (yellow) line, the system determines that the driver is
making a lane change and the LAS & LDWS operation is temporarily cancelled. The LAS
& LDWS becomes operational again when the system detects white (yellow) lane lines
while the vehicle is being driven normally within its vehicle lane.
xIf the vehicle deviates from its lane repeatedly within a short period of time, the LAS &
LDWS may not operate.
xWhen white (yellow) lane lines are not detected, the LAS & LDWS does not operate.
xUnder the following conditions, the LAS & LDWS may not be able to detect white (yellow)
lane lines correctly and it may not operate normally.
xIf an object placed on the instrument panel is reflected in the windscreen and picked up
by the camera.
xHeavy luggage is loaded in the luggage compartment or on the rear seat and the
vehicle is tilted.
xThe tyre pressures are not adjusted to the specified pressure.
xTyres other than conventional tyres are equipped.
xVehicle is driven on an intersection or junction, or on a forked road.
xThe white (yellow) lane lines are less visible because of dirt or fading/patchiness.
xA vehicle in front of your vehicle is running near a white (yellow) lane line making it
less visible.
xA white (yellow) lane line is less visible because of bad weather (rain, fog, or snow).
xThe vehicle is driven on a temporary lane or section with a closed lane resulting from
construction where there may be multiple white (yellow) lane lines or they are
interrupted.
:KHQ'ULYLQJ
L$&7,96(16(


Page 290 of 759

xIf you take your hands off the steering wheel (not holding the steering wheel), the warning
sound is activated and an alert is indicated in the active driving display or the warning
light turns on in the instrument cluster.

With Active Driving Display Without Active Driving Display
If the steering wheel is held lightly, or depending on the road conditions, the system may
detect that you have released the steering wheel (not holding the steering wheel) even if
you are holding it, and display a message in the active driving display.
xThe timing at which the lane departure warning is activated and the steering wheel
operation assist is performed varies.
xThe following settings for the LAS&LDWS can be changed. Refer to Personalisation
Features on page 9-15.
xSteering operation assist operational/non-operational
xCancel sensitivity (likelihood of steering assist)
9HKLFOHODQHOLQHGLVSOD\
:KHQWKH/$6 /':6GHWHFWVZKLWH \HOORZ OLQHVRQERWKWKHOHIWDQGULJKWVLGHVDQG
EHFRPHVRSHUDWLRQDOWKHYHKLFOHODQHOLQHVDUHLQGLFDWHGLQWKHDFWLYHGULYLQJGLVSOD\RUWKH
/$6 /':6LQGLFDWRUOLJKWWXUQVRQLQWKHLQVWUXPHQWFOXVWHU
With Active Driving Display Without Active Driving Display
$XWRFDQFHO
,QWKHIROORZLQJFDVHVWKH/$6 /':6LVDXWRPDWLFDOO\FDQFHOOHGDQGWKHYHKLFOHODQH
OLQHV VWDQGE\ DUHLQGLFDWHGLQWKHDFWLYHGULYLQJGLVSOD\,QDGGLWLRQZKHQWKH
/$6 /':6EHFRPHVRSHUDWLRQDOWKHV\VWHPWXUQVEDFNRQDXWRPDWLFDOO\DQGWKHYHKLFOH
ODQHOLQHV RSHUDWLRQDO DUHLQGLFDWHGLQWKHDFWLYHGULYLQJGLVSOD\
x7KHWHPSHUDWXUHLQVLGHWKHFDPHUDLVKLJKRUORZ
x7KHZLQGVFUHHQDURXQGWKHFDPHUDLVIRJJ\
x7KHZLQGVFUHHQDURXQGWKHFDPHUDLVEORFNHGE\DQREVWUXFWLRQFDXVLQJSRRUIRUZDUG
YLVLELOLW\
:KHQ'ULYLQJ
L$&7,96(16(


Page 295 of 759

▼/DQH'HSDUWXUH:DUQLQJ
,IWKHV\VWHPGHWHUPLQHVWKDWWKHYHKLFOHPD\GHYLDWHIURPLWVODQHWKHODQHGHSDUWXUH
ZDUQLQJ EHHSVRXQGUXPEOHVRXQG

RUVWHHULQJZKHHOYLEUDWLRQ LVDFWLYDWHGDQGWKH
GLUHFWLRQLQZKLFKWKHV\VWHPGHWHUPLQHVWKDWWKHYHKLFOHPD\GHYLDWHLVLQGLFDWHGLQWKH
DFWLYHGULYLQJGLVSOD\
,IWKHV\VWHPGHWHUPLQHVWKDWWKHYHKLFOHPD\GHYLDWHIURPLWVODQHWKHFRORXURIWKHODQH
OLQHRQWKHVLGHEHLQJGHWHFWHGE\WKHV\VWHPFKDQJHVIURPZKLWHWRDPEHUDQGIODVKHV
Warning light (Flashes) Active Driving Display
NOTE
xIf you have set the lane departure warning sound to the beep sound/rumble sound*1
setting, the warning sound may not be heard depending on the surrounding noise
conditions.
xIf you have set the lane departure warning system to the steering wheel vibrations setting,
the vibration may not be felt depending on the road surface conditions.
xWhen the setting for the steering operation assist is changed to operational, the warnings
can be set to activate/not activate. (When the setting for the steering operation assist is
changed to non-operational, the warnings cannot be set to not activate.)
Refer to Setting Change (Personalisation Features) on page 9-15.
xThe LAS & LDWS can be changed to the following settings regardless of whether the
steering operation assist has been set to operational/non-operational. Always check the
setting status when driving the vehicle and make setting changes if necessary.
Refer to Setting Change (Personalisation Features) on page 9-15.
xSteering wheel vibration: Strong/weak
xWarning sound volume
xTypes of warnings (steering wheel vibration/beep sound/rumble sound*1)
*1 A rumble strip is a series of grooves in the road pavement surface positioned at specific
intervals, and when the vehicle passes over it a vibration and rumble sound is produced
which alerts the driver that the vehicle is departing from the lane.
:KHQ'ULYLQJ
L$&7,96(16(


Page 310 of 759

xIf you suddenly come close to a vehicle ahead.
x2-wheeled vehicles, pedestrians, animals or standing trees.
xVehicle is driven with some of the tyres having significant wear.
x(Manual transaxle)
If the vehicle is stopped by the Smart City Brake Support (SCBS) operation and the clutch
pedal is not depressed, the engine stops.
▼6PDUW&LW\%UDNH6XSSRUW 6&%6
,QGLFDWRU/LJKW 5HG
,IWKH6PDUW&LW\%UDNH6XSSRUW 6&%6 LV
RSHUDWLQJWKHLQGLFDWRUOLJKW UHG IODVKHV

▼&ROOLVLRQ:DUQLQJ
,IWKHUHLVWKHSRVVLELOLW\RIDFROOLVLRQZLWK
DYHKLFOHDKHDGWKHEHHSVRXQGV
FRQWLQXRXVO\DQGDZDUQLQJLVLQGLFDWHGLQ
WKHDFWLYHGULYLQJGLVSOD\
NOTE
x(Without SCBS OFF switch)
The operation distance and volume of
the collision warning can be changed.
Refer to Personalisation Features on
page 9-15.
x(With SCBS OFF switch)
The operation distance and volume of
the collision warning can be changed.
Consult an Authorised Mazda Repairer.
▼▼$XWRPDWLF%UDNH2SHUDWLRQ'LVSOD\
7KHDXWRPDWLFEUDNHRSHUDWLRQGLVSOD\LV
LQGLFDWHGRQWKHDFWLYHGULYLQJGLVSOD\
DIWHUWKH6&%6)LVRSHUDWHG
NOTE
xThe collision warning beep sounds
intermittently while the SCBS F brake or
brake assist (SCBS F brake assist) is
operating.
xIf the vehicle is stopped by the SCBS F
operation and the brake pedal is not
depressed, the warning beep sounds 1
time after about 2 seconds and the SCBS
F brake is automatically released.
▼▼6WRSSLQJWKH6PDUW&LW\%UDNH
6XSSRUW>)RUZDUG@ 6&%6)
6\VWHP2SHUDWLRQ
7KH6&%6)V\VWHPFDQEHWHPSRUDULO\
GHDFWLYDWHG
:KHQWKH6&%6)V\VWHPLVWXUQHGRIIWKH
6PDUW&LW\%UDNH6XSSRUW 6&%6 2))
LQGLFDWRUOLJKWWXUQVRQ

:KHQWKHHQJLQHLVUHVWDUWHGWKHV\VWHP
EHFRPHVRSHUDWLRQDO
:KHQ'ULYLQJ
L$&7,96(16(


Page:   1-10 11-20 next >