key MAZDA MODEL 3 HATCHBACK 2004 (in English) Owner's Guide

7-10
In Case of an Emergency
Flat Tire
Form No. 8S18-EA-03I
To replace the nut
1. Place the key on top of the nut.
2. Place the lug wrench on top of the key,
apply pressure, and turn it clockwise.

Mounting the Spare Tire
1. Remove dirt and grime from the
mounting surfaces of the wheel and
hub, including the hub bolts, with a
cloth.
2. Mount the spare tire.3. Install the lug nuts with the beveled
edge inward; tighten them by hand.
Removing Dirt and Grime from
Wheels, Hubs and Hub Bolts:
When changing or replacing a tire,
not removing dirt and grime from the
mounting surfaces of the wheel, hub
and hub bolts is dangerous. The lug
nuts could loosen while driving and
cause the tire to come off, resulting in
an accident. Make sure the mounting
surfaces of the wheel, hub and lug
nuts are clean before changing or
replacing tires.
WARNING
Don’t Apply Oil or Grease to Lug
Nuts, Bolts:
Applying oil or grease to lug nuts and
bolts is dangerous. The lug nuts could
loosen while driving and cause the
tire to come off, resulting in an
accident. In addition, lug nuts and
bolts could be damaged if tightened
more than necessary. Do not apply oil
or grease to lug nuts and bolts and do
not tighten the lug nuts beyond the
recommended tightening torque.
WARNING
J48C_8S18-EA-03I_Edition1.book Page 10 Wednesday, August 6, 2003 8:51 AM

7-13
In Case of an Emergency
Form No. 8S18-EA-03I
Overheating
If the temperature gauge indicates
overheating, the vehicle loses power, or
you hear a loud knocking or pinging
noise, the engine is probably too hot.If the temperature gauge indicates
overheating:
1. Drive safely to the side of the road and
park off the right-of-way.
2. Put a vehicle with an automatic
transaxle in park (P), a manual
transaxle in neutral.
Apply the parking brake.
3. Turn off the air conditioner.
4. Check whether coolant or steam is
escaping from under the hood or from
the engine compartment.
If steam is coming from the engine
compartment:
Don’t go near the front of the vehicle.
Stop the engine.
Wait until the steam dissipates, then
open the hood and start the engine.
If neither coolant nor steam is
escaping:
Open the hood and idle the engine until
it cools.
5. Make sure the cooling fan is operating,
then turn off the engine after the
temperature has decreased.
Overheating
Cooling Fan and Engine
Inspection:
Inspecting the engine with the
ignition switch in the ON position is
dangerous. The cooling fan could
turn on unexpectedly even when the
engine isn’t running. You could be
seriously injured by the fan. Turn the
ignition switch off and remove the key
from the ignition switch when you
inspect the engine.
Cooling System Cap:
When the engine and radiator are
hot, scalding coolant and steam may
shoot out under pressure and cause
serious injury. Don’t remove the
cooling system cap when the engine
and radiator are hot.
Steam from Overheated Engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you. Open the hood
ONLY after steam is no longer
escaping from the engine.
WARNING
If the cooling fan does not operate
while the engine is running, the engine
temperature will increase. Stop the
engine and call an Authorized Mazda
Dealer.
CAUTION
J48C_8S18-EA-03I_Edition1.book Page 13 Wednesday, August 6, 2003 8:51 AM

7-15
In Case of an Emergency
Form No. 8S18-EA-03I
Emergency Starting
If the engine fails to start, it may be
flooded (excessive fuel in the engine).
Follow this procedure:
1. Depress the accelerator all the way and
hold it there.
2. Turn the ignition switch to the START
position and hold it there—for up to 10
seconds. If the engine starts, release the
key and accelerator immediately
because the engine will suddenly rev
up.
3. If the engine fails to start, crank it
without depressing the accelerator—
for up to 10 seconds.
Starting a Flooded Engine
J48C_8S18-EA-03I_Edition1.book Page 15 Wednesday, August 6, 2003 8:51 AM

8-11
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Improper or incomplete service may result in problems. This section gives instructions
only for items that are easy to perform.
As explained in the Introduction (page 8-2), several procedures can be done only by a
qualified service technician with special tools.
Improper owner maintenance during the warranty period may affect warranty coverage.
For details, read the separate Mazda Warranty statement provided with the vehicle. If
you’re unsure about any servicing or maintenance procedure, have it done by an
Authorized Mazda Dealer.
There are strict environmental laws regarding the disposal of waste oil and fluids. Please
dispose of your waste properly and with due regard to the environment.
We recommend that you entrust the oil and fluid changes of your vehicle to an Authorized
Mazda Dealer.
Owner Maintenance Precautions
Maintenance Procedures:
Performing maintenance work on a vehicle is dangerous if not done properly. You can
be seriously injured while performing some maintenance procedures. If you lack
sufficient knowledge and experience or the proper tools and equipment to do the
work, have it done by a qualified technician.
Running the Engine:
Working under the hood with the engine running is dangerous. It becomes even more
dangerous when you wear jewelry or loose clothing.
Either can become entangled in moving parts and result in injury.
Therefore, if you must run the engine while working under the hood, make certain
that you remove all jewelry (especially rings, bracelets, watches, and necklaces) and
all neckties, scarves, and similar loose clothing before getting near the engine or
cooling fan which may turn on unexpectedly.
Electrical Fan and Engine Inspection:
Inspecting the engine with the ignition switch in the ON position is dangerous. The
cooling fan could come on unexpectedly even when the engine isn’t running. You
could be seriously injured by the fan. Turn the ignition switch off and remove the key
from the ignition switch when you inspect the engine.
WARNING
J48C_8S18-EA-03I_Edition1.book Page 11 Wednesday, August 6, 2003 8:51 AM

8-15
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Changing oil filter
Because you need a special tool to
retighten the filter, an Authorized Mazda
Dealer should do the work.

Inspecting Coolant Level
NOTE
•The indicated engine oil capacities
are for general reference purposes
only. When adding or changing oil,
verify the engine oil level with the
oil dipstick.
•Use only specified engine oil (page
10-4).
Engine Coolant
Hot Engine:
A hot engine is dangerous. If the
engine has been running, parts of the
engine compartment can become very
hot. You could be burned. Carefully
inspect the engine coolant in the
coolant reservoir, but do not open it.
Do not use a match or live flame in
the engine compartment. DO NOT
ADD COOLANT WHEN THE
ENGINE IS HOT.
Cooling Fan and Engine
Inspection:
Inspecting the engine with the
ignition switch in the ON position is
dangerous. The cooling fan could
turn on unexpectedly even when the
engine isn’t running. You could be
seriously injured by the fan. Turn the
ignition switch off and remove the key
from the ignition switch when you
inspect the engine.
Cooling System Cap:
When the engine and radiator are
hot, scalding coolant and steam may
shoot out under pressure and cause
serious injury. Don’t remove the
cooling system cap when the engine
and radiator are hot.
WARNING
J48C_8S18-EA-03I_Edition1.book Page 15 Wednesday, August 6, 2003 8:51 AM

8-48
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I

Fuse Panel Description
Fuse block (Engine compartment)
12 3 45 6
789 10
11 12
13 14
15 16
17 18
1920 2122 23
24 25 26
27 2829
3031 3233 3435 36
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1 FAN 40A Cooling fan
2 P/ST 80A EHPAS
3BTN 40AFor protection of
various circuits
4HEAD 40AHeadlights
5PTC 80A—
6GLOW 60A—
7ABS 1 30A
ABS
*
8ABS 2 20A
ABS*
9 ENGINE 30AFor protection of
various circuits
10—— —
11 IG KEY 1 30A Ignition switch
12 STARTER 20A Starter clutch
13 IG KEY 2 30A Ignition switch
14—— —
15 HEATER 40A Blower motor
16—— —
17 DEFOG 40ARear window
defroster
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
18—— —
19 ABS IG 10A
ABS
*
20 FOG 15A
Fog lights*
21 HORN 15A Horn
22—— —
23 H/CLEAN 20A—
24 F/PUMP 15A Fuel pump
25 P/ST IG 10A Power steering
26 A/C MAG 10A Air conditioner
27 ALT 10A—
28—— —
29—— —
30 ENG +B 10A PCM
31 ROOM 15A Interior lights
32
ENG BAR 410AO2 heater
33
ENG BAR 310AO2 heater
34 EGI INJ 10A Injector
35
ENG BAR 110A Air flow sensor
36ENG BAR 210A EGR control valve
*Some models.
J48C_8S18-EA-03I_Edition1.book Page 48 Wednesday, August 6, 2003 8:51 AM

11-2
Form No. 8S18-EA-03I
Index
A
Add-On Non-Genuine Parts and
Accessories
...................................... 9-13
Air Bag Systems
.............................. 2-36
Air Filter
.......................................... 8-23
Antenna
............................................ 6-10
Anti-Lock Brake System (ABS)
........ 5-7
Warning light
.............................. 5-8
Appearance Care
.............................. 8-51
Ashtray
............................................. 6-40
Audio System
................................... 6-10
Audio control switch
................ 6-32
Audio set
................................... 6-17
Operating tips for audio
system
....................................... 6-10
Safety certification
.................... 6-34
Automatic Transaxle
Driving tips
............................... 5-16
Fluid
.......................................... 8-20
Manual shift mode
.................... 5-13
Shift-lock override
.................... 5-12
Shift-lock system
...................... 5-12
Transaxle ranges
....................... 5-11
B
Battery
Emergency starting
................... 7-15
Maintenance
............................. 8-28
Specifications
........................... 10-4
Beep Sounds
Ignition key reminder
............... 5-43
Lights-on reminder
................... 5-43
Seat belt warning beep
.............. 5-43
Tire inflation pressure warning
beep
........................................... 5-43
Before Starting the Engine
................. 4-6
After getting in
........................... 4-6
Before getting in
......................... 4-6
B
Body Lubrication ............................. 8-22
Bottle Holder
.................................... 6-42
Brake/Clutch
Fluid
.......................................... 8-18
Brakes
Anti-lock brake system (ABS)
....5-7
Brakes assist
................................5-8
Foot brake
................................... 5-4
Parking brake
.............................. 5-5
Warning light
.............................. 5-6
Break-In Period
.................................. 4-7
Bulb Replacement
............................ 8-36
C
Capacities ......................................... 10-5
Carbon Monoxide
.............................. 4-5
Cargo Securing Loops
...................... 6-43
Cargo Sub-Compartment
................. 6-44
Catalytic Converter
............................ 4-3
Cell Phones
...................................... 9-14
Center Console
................................. 6-43
Child Restraint
Child restraint precautions
........ 2-21
Installing child-restraint
systems
...................................... 2-25
LATCH child-restraint
systems
...................................... 2-32
Child Safety Locks for Rear
Doors
.................................................. 3-9
Cigarette Lighter
.............................. 6-40
Climate Control System
.....................6-2
Gas specifications
..................... 10-6
Clock
................................................ 6-39
Cruise Control
.................................. 5-18
Cup Holder
....................................... 6-41
Customer Assistance
.......................... 9-2
J48C_8S18-EA-03I_Edition1.book Page 2 Wednesday, August 6, 2003 8:51 AM

11-4
Index
Form No. 8S18-EA-03I
H
Hood Release ................................... 3-20
Horn
................................................. 5-53
I
Ignition
Keys
............................................ 3-2
Switch
......................................... 5-2
Illuminated Entry System
................ 6-35
Immobilizer System
......................... 3-24
Indicator Lights
................................ 5-31
Cruise main
............................... 5-41
Cruise set
.................................. 5-41
Headlight high-beam
................ 5-40
power steering malfunction
...... 5-41
Security
..................................... 5-40
Shift position
............................ 5-40
Turn-signal/hazard warning
...... 5-42
Information Display
......................... 6-38
Audio display
............................ 6-39
Clock
......................................... 6-39
Information display functions
... 6-38
Inside Trunk Release
Handle/Slide Lever
.......................... 3-16
Instrument Cluster
........................... 5-26
Instrument Cluster Dimmer Select
Button
.............................................. 5-30
Interior Care
..................................... 8-57
Interior Lights
.................................. 6-35
J
Jump-Starting ................................... 7-16
K
Keyless Entry System ........................ 3-3
Keys
................................................... 3-2
L
Label Information ............................ 10-2
Lane-Change Signals
....................... 5-47
Liftgate
............................................. 3-10
Luggage compartment
.............. 3-11
Light Bulbs
Replacement
.............................. 8-36
Specifications
............................ 10-7
Lighter
.............................................. 6-40
Lighting Control
............................... 5-44
Lubricant Quality
............................. 10-4
Luggage Compartment Light
........... 6-37
M
Maintenance
Introduction
................................. 8-2
Owner maintenance
precautions
................................ 8-11
Owner maintenance schedule
... 8-10
Scheduled
.................................... 8-3
Manual Transaxle Operation
.............. 5-9
Recommendations for
shifting
...................................... 5-10
Map Lights
....................................... 6-37
Meters and Gauges
........................... 5-26
Mirrors
Outside mirrors
......................... 3-29
Rearview mirror
........................ 3-31
Money-Saving Suggestions
................ 4-7
Moonroof
......................................... 3-22
O
Odometer and Trip Meter ................ 5-27
Outside Mirrors
................................ 3-29
Overhead Lights
............................... 6-36
Overheating
...................................... 7-13
Overloading
...................................... 4-12
J48C_8S18-EA-03I_Edition1.book Page 4 Wednesday, August 6, 2003 8:51 AM