buttons MAZDA MODEL 3 HATCHBACK 2014 (in English) User Guide

5–83
Interior Features
Bluetooth®
NOTE
 


y If a Bluetooth ® device has already
been programmed to the vehicle as a
hands-free mobile phone, it does not
need to be programmed again when
using the device as a Bluetooth
® audio
device. Conversely, it does not need to
be programmed again as a hands-free
mobile phone if it has already been
programmed as a Bluetooth
® audio
device.
 


y Device registration can also be done
using voice recognition.
Concerning the operation of a Bluetooth
®
audio device itself, refer to its instruction
manual.
Some Bluetooth
® audio devices have PIN
codes (four digits). Refer to the audio
device's instruction manual because the
programming procedure differs depending
on whether it has a PIN code or not.
Programming a Bluetooth
® audio device
which has a four-digit PIN code
1. Using the audio control dial, select
the pairing program mode “ PAIR
DEVICE ” in the “ BT SETUP ” mode.
(Refer to “Bluetooth
® audio device set-
up” for details.)
2. Press the audio control dial to
determine the mode. After “ ENTER
PIN ” is displayed on the audio display
for three seconds, “ PIN 0000 ” is
displayed and the PIN code can be
input. 3. Input the PIN code of your Bluetooth
®
audio device by pressing channel preset
buttons 1 to 4 while “ PIN 0000 ” is
displayed.
Press channel preset button 1 to input
the fi rst digit, 2 for the second, 3 for the
third, and 4 for the forth. For example,
if the PIN code were “4213” press
channel preset button 1 four times (1,
2, 3, 4), button 2 twice (1, 2), button
3 once (1), and button 4 three times
(1, 2, 3). If the “ PIN 0000 ” display
disappears before fi nishing the PIN
code input, repeat the procedure from
Step 1.
NOTE
Some devices accept only a particular
pairing code (Usually, “0000” or
“1234”).
If pairing cannot be completed, refer to the
owner's manual of your mobile device, and
try those numbers if necessary.
4. Press the audio control dial while
the input PIN code is displayed.
“ PAIRING ” fl ashes on the audio
display.
5. Operate the Bluetooth
® audio device
and set it to the program mode while
“ PAIRING ” is fl ashing.
6. When the programming is completed,
and “ PAIR SUCCESS ” are displayed
after about 10-30 seconds, after which
“ PAIR SUCCESS ” continues to be
displayed for three seconds, and then
the unit returns to the normal display.
/C\FCA&('#*A'FKVKQPKPFD

6–39
Maintenance and Care
Owner Maintenance
Battery Replacement
If the buttons on the transmitter are
inoperable and the operation indicator
light does not fl ash, the battery may be
dead.
Replace with a new battery before the
transmitter becomes unusable.
CAUTION
 


¾ Make sure the battery is installed
correctly. Battery leakage could occur if
it is not installed correctly.
 


¾ When replacing the battery, be careful
not to touch any of the internal circuitry
and electrical terminals, bend the
electrical terminals, or get dirt in the
transmitter as the transmitter could be
damaged.
 


¾ There is the danger of explosion if the
battery is not correctly replaced.
 


¾ Dispose of used batteries according to
the following instructions.
 


¾ Insulate the plus and minus terminals
of the battery using cellophane or
equivalent tape.
 


¾ Never disassemble.



¾ Never throw the battery into fi re or
water.
 


¾ Never deform or crush.




¾ Replace only with the same type battery
(CR2025 or equivalent).
The following conditions indicate that the
battery power is low:
 


y The KEY indicator light (green) fl ashes
in the instrument cluster for about 30
seconds after the engine is turned off.
 


y The system does not operate and
the operation indicator light on the
transmitter does not fl ash when the
buttons are pressed.
 


y The system's operational range is
reduced.
Replacing the battery at an Authorized
Mazda Dealer is recommended to prevent
damage to the key. If replacing the battery
by yourself, follow the instruction below.
Replacing the key battery
1. Pull out the auxiliary key.
2. Insert a small, fl athead screwdriver
into the groove shown in the fi gure and
rotate the screwdriver to open the cover
slightly.
/C\FCA&('#*A'FKVKQPKPFD