dead battery MAZDA MODEL 3 HATCHBACK 2014 Owners Manual (in English)

3–4
Before Driving
Keys
CAUTION
Radio equipment like this is governed
by laws in the United States.
Changes or modifi cations not expressly
approved by the party responsible
for compliance could void the user's
authority to operate the equipment.
NOTE
 


y The keyless entry system operation may
vary due to local conditions.
 


y The keyless entry system is fully
operational (door/liftgate/trunk lid
lock/unlock) when the push button
start is switched off. The system does
not operate if the push button start is
switched to any position other than off.
 


y If the key does not operate when
pressing a button or the operational
range becomes too small, the battery
may be dead. To install a new battery,
refer to Replace Electrical Battery
(page 6-39 ).
 


y Additional keys can be obtained at
an Authorized Mazda Dealer. Up to
6 keys can be used with the keyless
functions per vehicle. Bring all keys
to an Authorized Mazda Dealer when
additional keys are required.
Transmitter
NOTE
 


y(With theft-deterrent system)
 The hazard warning lights fl ash when
the theft-deterrent system is armed or
turned off.
 Refer to Theft-Deterrent System on
page 3-43
 

y

 (With the advanced keyless function)
 A beep sound can be heard for
confi rmation when the doors and
liftgate/trunk lid are locked/unlocked
using the key. If you prefer, the beep
sound can be turned off.
  The volume of the beep sound can also
be changed.
Refer to Personalization Features on
page 9-12
 Use the following procedure to change
the setting.
1. Switch the ignition off and close all
of the doors and the liftgate/trunk
lid.
2. Open the driver's door.
3. Within 30 seconds of opening the
driver's door, press and hold the
LOCK button on the key for 5
seconds or longer.
All of the doors and the liftgate/
trunk lid lock and the beep sound
activates at the currently set volume.
(If the beep sound is currently set
to not activate, it will not activate.)
The setting changes each time the
LOCK button on the key is pressed
and the beep sound activates at the
set volume. (If the beep sound has
been set to not activate, it will not
activate.)
/C\FCA&('#*A'FKVKQPKPFD

*Some models.3–9
Before Driving
Advanced Keyless Entry System
Advanced Keyless Entry
System
*
WARNING
Radio waves from the key may aff ect
medical devices such as pacemakers:
Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will aff ect
the device.
The advanced keyless function allows you
to lock/unlock the doors and liftgate/trunk
lid, or open the liftgate/trunk lid while
carrying the key without using the key.
System malfunctions or warnings are
indicated by the following warning beeps.
 


y Request switch Inoperable Warning
Beep
  Refer to Request Switch Inoperable
Warning Beep (With the advanced
keyless function) on page 7-37 .




y Key Left-in-luggage Compartment/
Trunk Warning Beep
  Refer to Key Left-in-luggage
Compartment Warning Beep (With the
advanced keyless function) on page
7-37 .
 


y Key Left-in-vehicle Warning Beep
 Refer to Key Left-in-vehicle Warning
Beep (With the advanced keyless
function) on page 7-38 .
NOTE
The advanced keyless entry system
functions can be deactivated to prevent
any possible adverse effect on a user
wearing a pacemaker or other medical
device. If the system is deactivated, you
will be unable to start the engine by
carrying the key. Consult an Authorized
Mazda Dealer for details. If the advanced
keyless entry system has been deactivated,
you can start the engine by following the
procedure indicated when the key battery
goes dead.
Refer to Engine Start Function When Key
Battery is Dead on page 4-8 .
/C\FCA&('#*A'FKVKQPKPFD

*Some models.3–43
Before Driving
Security System
Theft-Deterrent System *
If the theft deterrent system detects an
inappropriate entry into the vehicle,
which could result in the vehicle or its
contents being stolen, the alarm alerts the
surrounding area of an abnormality by
sounding the horn and fl ashing the hazard
warning lights.
The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Operation
System triggering conditions
The horn sounds intermittently and the
hazard warning lights fl ash for about 30
seconds when the system is triggered by
any one of the following:
 


y Unlocking a door with the key, door
lock switch, or an inside door-lock knob.
 


y Forcing open a door, the hood or the
liftgate/trunk lid.
 


y Opening the hood by operating the hood
release handle.
 


y Switching the ignition ON without using
the push button start.
If the system is triggered again, the lights
and horn will activate until the driver's
door or the liftgate/trunk lid is unlocked
with the transmitter.
(With advanced key)
The lights and horn can also be
deactivated by pressing the request switch
on a door.
NOTE
If the battery goes dead while the theft-
deterrent system is armed, the horn will
activate and the hazard warning lights
will fl ash when the battery is charged or
replaced.
How to Arm the System
1. Close the windows and the moonroof *
securely.
2. Press the push button start off.
3. Make sure the hood, the doors, and the
liftgate/trunk lid are closed.
4. Press the lock button on the transmitter
or lock the driver's door from the
outside with the auxiliary key.
The hazard warning lights will fl ash
once.
The following method will also arm the
theft-deterrent system:
Press the door-lock switch “
” while
any door is open and then close all of
the doors.
(With the advanced keyless function)
Press a request switch.
The security indicator light in the
instrument panel fl ashes twice per
second for 20 seconds.
5. After 20 seconds, the system is fully
armed.
/C\FCA&('#*A'FKVKQPKPFD

4–4
When Driving
Start/Stop Engine
Ignition Switch
Push Button Start Positions
The system operates only when the driver
is in the vehicle or within operational
range while the key is being carried.
Each time the push button start is pressed,
the ignition switches in the order of off,
ACC, and ON. Pressing the push button
start again from ON switches the ignition
off.
Indicator light
NOTE
 


y The engine starts by pressing the push
button start while depressing the clutch
pedal (manual transaxle) or the brake
pedal (automatic transaxle). To switch
the ignition position, press the push
button start without depressing the
pedal.
 


y Do not leave the ignition switched ON
while the engine is not running. Doing
so could result in the battery going
dead. If the ignition is left in ACC (For
automatic transaxle, the selector lever
is in the P position, and the ignition
is in ACC), the ignition switches off
automatically after about 25 minutes. off
The power supply to electrical devices
turns off and the push button start indicator
light (amber) also turns off.
This position is in which the steering
wheel is locked.
WARNING
Before leaving the driver's seat, always
switch the ignition off , set the parking
brake, and make sure the selector lever
is in P (automatic transaxle) or in 1st
gear or R (manual transaxle):
Leaving the driver's seat without
switching the ignition off , setting the
parking brake, and shifting the selector
lever to P (automatic transaxle) or
to 1st gear or R (manual transaxle)
is dangerous. Unexpected vehicle
movement could occur which could
result in an accident.
In addition, if your intention is to leave
the vehicle for even a short period, it
is important to switch the ignition off ,
as leaving it in another position will
disable some of the vehicle's security
systems and run the battery down.
ACC (Accessory)
Some electrical accessories will operate
and the indicator light (amber) illuminates.
NOTE
The keyless entry system does not function
while the push button start has been
pressed to ACC, and the doors will not
lock/unlock even if they have been locked
manually.
/C\FCA&('#*A'FKVKQPKPFD

4–6
When Driving
Start/Stop Engine
NOTE
 


y The key must be carried because the
key carries an immobilizer chip that
must communicate with the engine
controls at short range.
 


y The engine can be started when the
push button start is pressed from off,
ACC, or ON.
 


y The push button start system functions
(function which can start the engine
by only carrying the key) can be
deactivated to prevent any possible
adverse effect on a user wearing a
pacemaker or other medical device. If
the system is deactivated, you will be
unable to start the engine by carrying
the key. Consult an Authorized Mazda
Dealer for details. If the push button
start system functions have been
deactivated, you can start the engine by
following the procedure indicated when
the key battery goes dead.
  Refer to Engine Start Function When
Key Battery is Dead on page 4-8 .




y After starting a cold engine, the engine
speed increases and a whining sound
from the engine compartment can be
heard.
  This is for improved exhaust gas
purifi cation and does not indicate
defect of the parts.
 


y Engine-starting is controlled by the
spark ignition system.
  This system meets all Canadian
Interference-Causing Equipment
Standard requirements regulating the
impulse electrical fi eld strength of radio
noise.
1. Make sure you are carrying the key.
2. Occupants should fasten their seat
belts.
3. Make sure the parking brake is on. 4. Continue to press the brake pedal
fi rmly until the engine has completely
started.
5. (Manual transaxle)
Continue to press the clutch pedal
fi rmly until the engine has completely
started.
(Automatic transaxle)
Put the vehicle in park (P). If you must
restart the engine while the vehicle is
moving, shift into neutral (N).
NOTE
(Manual transaxle)
The starter will not operate if the clutch
pedal is not depressed suffi ciently.
(Automatic transaxle)
The starter will not operate if the selector
lever is not in P or N and the brake pedal
is not depressed suffi ciently.
6. Verify that the KEY indicator light
(green) in the instrument cluster and the
push button start indicator light (green)
illuminate.
Indicator light
/C\FCA&('#*A'FKVKQPKPFD

4–7
When Driving
Start/Stop Engine
NOTE
 


y If the push button start indicator light
(green) fl ashes, make sure that the key
is being carried.
 


y If the push button start indicator light
(green) fl ashes with the key being
carried, touch the key to the push
button start and start the engine. Refer
to Engine Start Function When Key
Battery is Dead on page 4-8 .

CAUTION
If the KEY warning light (red)
illuminates, or the push button
start indicator light (amber) fl ashes,
this could indicate a problem with
the engine starting system and the
inability to start the engine or switch
the ignition to ACC or ON. Have your
vehicle inspected at an Authorized
Mazda Dealer as soon as possible.
NOTE
 


y Under the following conditions, the
KEY warning light (red) fl ashes after
the push button start is pressed to
inform the driver that the push button
start will not switch to ACC even if it is
pressed from off.
 


y The key battery is dead.



y The key is out of operational range.



y The key is placed in areas where it is
diffi cult for the system to detect the
signal (page 3-7 ).




y A key from another manufacturer
similar to the key is in the
operational range.
 


y(Forced engine starting method)
 If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) fl ashes, this
could indicate that the engine may not
start using the usual starting method.
Have your vehicle inspected at an
Authorized Mazda Dealer as soon as
possible. If this occurs, the engine can
be force-started. Press and hold the
push button start until the engine starts.
Other procedures necessary for starting
the engine such as having the key in the
cabin, and depressing the clutch pedal
(manual transaxle) or the brake pedal
(automatic transaxle) are required.
 


y When the engine is force-started,
the KEY warning light (red) remains
illuminated and the push button
start indicator light (amber) remains
fl ashing.
 


y(Automatic transaxle)
 When the selector lever is in the
neutral (N) position, the KEY indicator
light (green) and the push button
start indicator light (green) do not
illuminate.
7. Press the push button start after both
the KEY indicator light (green) in the
instrument cluster and the push button
start indicator light (green) illuminate.
NOTE
 


y After starting the engine, the push
button start indicator light (amber)
turns off and the ignition switches to the
ON position.
 


y After pressing the push button start and
before the engine starts, the operation
sound of the fuel pump motor from near
the fuel tank can be heard, however, this
does not indicate a malfunction.
/C\FCA&('#*A'FKVKQPKPFD

4–8
When Driving
Start/Stop Engine
8. After starting the engine, let it idle for
about ten seconds.
NOTE
 






y Whether the engine is cold or warm, it
should be started without the use of the
accelerator.
 


y If the engine does not start the fi rst
time, refer to Starting a Flooded Engine
under Emergency Starting. If the engine
still does not start, have your vehicle
inspected by an Authorized Mazda
Dealer (page 7-18 ).
Engine Start Function When Key
Battery is Dead
CAUTION
When starting the engine by holding
the transmitter over the push button
start due to a dead key battery or a
malfunctioning key, be careful not
to allow the following, otherwise the
signal from the key will not be received
correctly and the engine may not start.
 


¾ Metal parts of other keys or metal
objects touch the key.
 




¾ Spare keys or keys for other vehicles
equipped with an immobilizer system
touch or come near the key.
 




¾ Devices for electronic purchases, or
security passage touch or come near
the key.
If the engine cannot be started due to a
dead key battery, the engine can be started
using the following procedure:
1. Depress the brake pedal fi rmly.
2. (Manual transaxle)
Continue to depress the clutch pedal
fi rmly until the engine has completely
started.
/C\FCA&('#*A'FKVKQPKPFD

6–39
Maintenance and Care
Owner Maintenance
Battery Replacement
If the buttons on the transmitter are
inoperable and the operation indicator
light does not fl ash, the battery may be
dead.
Replace with a new battery before the
transmitter becomes unusable.
CAUTION
 


¾ Make sure the battery is installed
correctly. Battery leakage could occur if
it is not installed correctly.
 


¾ When replacing the battery, be careful
not to touch any of the internal circuitry
and electrical terminals, bend the
electrical terminals, or get dirt in the
transmitter as the transmitter could be
damaged.
 


¾ There is the danger of explosion if the
battery is not correctly replaced.
 


¾ Dispose of used batteries according to
the following instructions.
 


¾ Insulate the plus and minus terminals
of the battery using cellophane or
equivalent tape.
 


¾ Never disassemble.



¾ Never throw the battery into fi re or
water.
 


¾ Never deform or crush.




¾ Replace only with the same type battery
(CR2025 or equivalent).
The following conditions indicate that the
battery power is low:
 


y The KEY indicator light (green) fl ashes
in the instrument cluster for about 30
seconds after the engine is turned off.
 


y The system does not operate and
the operation indicator light on the
transmitter does not fl ash when the
buttons are pressed.
 


y The system's operational range is
reduced.
Replacing the battery at an Authorized
Mazda Dealer is recommended to prevent
damage to the key. If replacing the battery
by yourself, follow the instruction below.
Replacing the key battery
1. Pull out the auxiliary key.
2. Insert a small, fl athead screwdriver
into the groove shown in the fi gure and
rotate the screwdriver to open the cover
slightly.
/C\FCA&('#*A'FKVKQPKPFD

*Some models.7–33
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning Action to be taken
(Amber)
Forward
Obstruction
Warning/
Smart
City Brake
Support
(FOW/
SCBS)
Indicator
Light
*
The light turns on if the windshield and the radar
sensor are dirty or there is a malfunction in the
system. Verify the reason why the warning light is
illuminated on the audio display (page 7-24 ).
If the reason why the warning light is
illuminated is due to a dirty windshield, clean
the windshield.
If the warning light is illuminated because of a
dirty radar sensor, clean the front emblem.
For any other reasons, have the vehicle
inspected at an Authorized Mazda Dealer.
KEY Warning Light
Take the appropriate action and verify that the warning light turns off.
Signal Cause Action to be taken
(Red)
(Flashing) The advanced key battery is dead. Replace the battery (page 6-39 ).
The advanced key is not within the
operation range.
Bring the advanced key into the operation
range (page 3-7 ). The advanced key is placed in areas inside
the cabin where it is diffi cult for the key to
be detected.
A key from another manufacturer similar to
the advanced key is in the operation range. Take the key from another manufacturer
similar to the advanced key out of the
operation range.
Without the ignition switched off, the
advanced key is taken out of the cabin, and
then all the door are closed. Bring the advanced key back into the
cabin.
/C\FCA&('#*A'FKVKQPKPFD

7–40
If Trouble Arises
When Liftgate/Trunk Lid Cannot be Opened
When Liftgate/Trunk Lid
Cannot be Opened
If the vehicle battery is dead or there is a
malfunction in the electrical system and
the liftgate/trunk lid can not be opened,
perform the following procedure as an
emergency measure to Open it:
(5–door)
1. Remove the cap on the interior
surface of the liftgate with a fl athead
screwdriver.
Cap
2. Turn the lever to the right to unlock the
liftgate.
Lever
Cap
(4–door)
1. Open the cover.
2. Open the cap.
Cover
Cap
3. Turn the screw counterclockwise and
remove it, and then remove the cap.
Screw
/C\FCA&('#*A'FKVKQPKPFD