ECO mode MAZDA MODEL 3 HATCHBACK 2015 Owners Manual (in English)

*Some models.7–37
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
Automatic
Transaxle Warning
Light
*
The light/indication illuminates when the transaxle has a problem.
CAUTION
If the automatic transaxle warning light illuminates, the transaxle
has an electrical problem. Continuing to drive your Mazda in this
condition could cause damage to your transaxle. Consult an expert
repairer, we recommend an Authorised Mazda Repairer as soon as
possible.
Air Bag/Seat
Belt Pretensioner
System Warning
Light A system malfunction is indicated if the warning light constantly fl ashes, constantly
illuminates or does not illuminate at all when the ignition is switched ON. If any of these
occur, consult an expert repairer, we recommend an Authorised Mazda Repairer as soon as
possible. The system may not operate in an accident. WARNING
Never tamper with the air bag/pretensioner systems and always have an expert
repairer, we recommend an Authorised Mazda Repairer perform all servicing and
repairs:
Self-servicing or tampering with the systems is dangerous. An air bag/pretensioner
could accidentally activate or become disabled causing serious injury or death.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–38
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
Tyre Pressure
Monitoring System
Warning Light
*
If the tyre pressure monitoring system has a malfunction, the tyre pressure warning
light fl ashes for about 1 minute when the ignition is switched ON and then continues
illuminating. Have your vehicle checked by an expert repairer, we recommend an
Authorised Mazda Repairer as soon as possible.
WARNING

If the tyre pressure monitoring system warning light illuminates or fl ashes, or the
tyre pressure warning beep sound is heard, decrease vehicle speed immediately and
avoid sudden manoeuvring and braking:
If the tyre pressure monitoring system warning light illuminates or fl ashes, or the
tyre pressure warning beep sound is heard, it is dangerous to drive the vehicle at high
speeds, or perform sudden manoeuvring or braking. Vehicle drivability could worsen
and result in an accident.
To determine if you have a slow leak or a fl at, pull over to a safe position where you
can check the visual condition of the tyre and determine if you have enough air
to proceed to a place where air may be added and the system monitored again by
an expert repairer, we recommend an Authorised Mazda Repairer or a tyre repair
station.
Do not ignore the TPMS Warning Light:
Ignoring the TPMS warning light is dangerous, even if you know why it is
illuminated. Have the problem taken care of as soon as possible before it develops
into a more serious situation that could lead to tyre failure and a dangerous accident.
(Red)
(Illuminate)
KEY Warning Light If any malfunction occurs in the keyless entry system, it illuminates continuously.
CAUTION
If the key warning indicator light illuminates or the push button start indicator light
(amber) fl ashes, the engine may not start. If the engine cannot be started, try starting it
using the emergency operation for starting the engine, and have the vehicle inspected at
an expert repairer, we recommend an Authorised Mazda Repairer as soon as possible.
Refer to Emergency Operation for Starting the Engine on page 4-11 .
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–39
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
(Amber)
(Flashing)
Lane Departure
Warning System
(LDWS) Warning
Light
*
The warning light fl ashes when the system has a malfunction. Have your vehicle inspected
at an expert repairer, we recommend an Authorised Mazda Repairer.
The LDWS does not operate when the warning light fl ashes.
CAUTION
If any of the following cases occurs, the system may have a malfunction. Have the
vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
The light fl ashes while the vehicle is being driven. The light does not illuminate when the ignition is switched ON. Always use tyres for all wheels that are of the specifi ed size, and the same
manufacture, brand, and tread pattern. In addition, do not use tyres with signifi cantly
different wear patterns on the same vehicle. If such improper tyres are used, the
LDWS may not operate normally.
When an emergency spare tyre is used, the system may not operate normally.
Headlight
Auto-Levelling
Malfunction
Indicator Light
*
This indicator light stays on for a few seconds when the ignition is switched ON.
Thereafter, the indicator light will illuminate when the headlight auto-levelling system has
a malfunction.
If the indicator light illuminates, contact an expert repairer, we recommend an Authorised
Mazda Repairer.
NOTE
Vehicles with the adaptive front lighting system (AFS) are not equipped with the
headlight auto-levelling malfunction indicator light. If there is a malfunction with the
headlight auto-levelling function, the AFS OFF indicator light fl ashes.
(Amber)
High Beam Control
System (HBC)
Warning Light
*
When illuminated
The warning light illuminates if the area of the windscreen in front of the forward sensing
camera (FSC) is fogged or obstructed.
When fl ashing
This light fl ashes if there is a malfunction in the high beam control system (HBC). Have
your vehicle inspected by an expert repairer, we recommend an Authorised Mazda Repairer.
(Amber)
(Flashing)
Mazda Radar
Cruise Control
(MRCC) Warning
Light
*
The warning light fl ashes if there is a malfunction in the system while the Mazda Radar
Cruise Control (MRCC) system is on. Have your vehicle inspected at an expert repairer, we
recommend an Authorised Mazda Repairer.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–43
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning Action to be taken
Tyre Pressure
Monitoring System
Warning Light
*
When the warning light illuminates, and
the warning beep sound is heard (about 3
seconds), tyre pressure is too low in one or
more tyres.
WARNING
If the tyre pressure monitoring system
warning light illuminates or fl ashes,
or the tyre pressure warning beep
sound is heard, decrease vehicle
speed immediately and avoid sudden
manoeuvring and braking:
If the tyre pressure monitoring system
warning light illuminates or fl ashes, or
the tyre pressure warning beep sound
is heard, it is dangerous to drive the
vehicle at high speeds, or perform
sudden manoeuvring or braking.
Vehicle drivability could worsen and
result in an accident.
To determine if you have a slow leak or
afl at, pull over to a safe position where
you can check the visual condition
of the tyre and determine if you have
enough air to proceed to a place where
air may be added and the system
monitored again by an expert repairer,
we recommend an Authorised Mazda
Repairer or a tyre repair station.
Do not ignore the TPMS Warning
Light:
Ignoring the TPMS warning light is
dangerous, even if you know why it is
illuminated. Have the problem taken
care of as soon as possible before it
develops into a more serious situation
that could lead to tyre failure and a
dangerous accident. Inspect the tyres and adjust to the specifi ed
infl ation pressure (page 6-46 ).
NOTE
Perform tyre pressure adjustment when
the tyres are cold. Tyre pressure will
vary according to the tyre temperature,
therefore let the vehicle stand for 1
hour or only drive it 1.6 km (1 mile) or
less before adjusting the tyre pressures.
When pressure is adjusted on hot
tyres to the cold infl ation pressure, the
TPMS warning light/beep may turn on
after the tyres cool and pressure drops
below specifi cation.
Also, an illuminated TPMS warning
light, resulting from the tyre air
pressure dropping due to cold ambient
temperature will remain illuminated
even if the ambient temperature rises.
In this case, it will also be necessary
to adjust the tyre air pressures. If the
TPMS warning light illuminates due
to a drop in tyre air pressure, make
sure to check and adjust the tyre air
pressures.
Tyres lose air naturally over time
and the TPMS cannot tell if the tyres
are getting too soft over time or you
have a fl at. However, when you fi nd
one low tyre in a set of four-that is
an indication of trouble; you should
have someone drive the vehicle slowly
forward so you can inspect any low
tyre for cuts and any metal objects
sticking through tread or sidewall. Put
a few drops of water in the valve stem
to see if it bubbles indicating a bad
valve. Leaks need to be addressed by
more than simply reinfl ating the tyre
as leaks are dangerous — take it to
an expert repairer, we recommend an
Authorised Mazda Repairer.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–44
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning Action to be taken
(Amber)
Smart Brake
Support/Smart
City Brake Support
(SBS/SCBS)
Warning Light
*
The light turns on if the windscreen and
the radar sensor are dirty or there is a
malfunction in the system.
(Vehicles with type C/type D audio)
Verify the reason why the warning light
is illuminated on the centre display (page
7-32 ).
If the reason why the warning light is
illuminated is due to a dirty windscreen,
clean the windscreen.
If the warning light is illuminated because
of a dirty radar sensor, clean the front
emblem.
For any other reasons, have the vehicle
inspected at an expert repairer, we
recommend an Authorised Mazda Repairer.
(Vehicles without type C/type D audio)
If the reason why the warning light is
illuminated is due to a dirty windscreen,
clean the windscreen. For any other reasons,
have the vehicle inspected at an expert
repairer, we recommend an Authorised
Mazda Repairer.
KEY Warning Light
Take the appropriate action and verify that the warning light turns off.
Signal Cause Action to be taken
(Red)
(Flashing) The advanced key battery is dead. Replace the key battery (page 6-43 ).
The advanced key is not within the
operation range.
Bring the advanced key into the operation
range (page 3-7 ). The advanced key is placed in areas inside
the cabin where it is diffi cult for the key to
be detected.
A key from another manufacturer similar to
the advanced key is in the operation range. Take the key from another manufacturer
similar to the advanced key out of the
operation range.
Without the ignition switched off, the
advanced key is taken out of the cabin, and
then all the door are closed. Bring the advanced key back into the
cabin.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–50
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Seat Belt Warning Beep
Front seat
If the vehicle speed exceeds about 20
km/h (12 mph) with the driver or front
passenger's seat belt unfastened, a warning
beep sounds continuously. If the seat belt
remains unfastened, the beep sound stops
once and then continues for about 90
seconds. The beep stops after the driver or
front passenger's seat belt is fastened.
NOTE
  Some models do not have the seat
belt warning beep for the front
passenger's seat.
  Placing heavy items on the front
passenger seat may cause the front
passenger seat belt warning function
to operate depending on the weight
of the item.
  To allow the front passenger seat
weight sensor to function properly,
do not place and sit on an additional
seat cushion on the front passenger
seat. The sensor may not function
properly because the additional
seat cushion could cause sensor
interference.
  When a small child sits on the front
passenger seat, it is possible that the
warning beep will not operate.
Rear seat
The warning beep only sounds if a seat
belt is unfastened after being fastened.
Ignition Not Switched Off (STOP)
Warning Beep *
If the driver's door is opened while
the ignition is switched to ACC, a
continuous beep sound will be heard to
notify the driver that the ignition has not
been switched off (STOP). Left in this
condition, the keyless entry system will
not operate, the car cannot be locked, and
the battery power will be depleted.
Key Removed from Vehicle
Warning Beep
A beep sound will be heard 6 times and
the KEY warning light (red) will fl ash
continuously if the ignition has not been
switched off, all the doors are closed, and
the key is removed from the vehicle. This
is to notify the driver that the key has been
removed from the vehicle and the ignition
has not been switched off.
NOTE
Because the key utilizes low-intensity
radio waves, the Key Removed From
Vehicle Warning may activate if the key
is carried together with a metal object
or it is placed in a poor signal reception
area.
Request Switch Inoperable
Warning Beep (With the advanced
keyless function)
If the request switch is pressed with a door
open or ajar or the ignition has not been
switched off while the key is being carried,
a beep will be heard for about 2 seconds to
indicate that the doors and the liftgate/boot
lid cannot be locked.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–51
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Key Left-in-luggage Compartment
Warning Beep (With the advanced
keyless function)
If the key is left in the boot with all doors
locked and the boot lid closed, a beep
sound is heard for about 10 seconds to
remind the driver the key has been left in
the boot. If this happens, open the boot
lid by pressing the electric boot lid opener
and remove the key. A key removed from
the boot may not function because its
functions may have been temporarily
suspended. To restore the key function,
perform the applicable procedure (page
3-8 ).
Key Left-in-vehicle Warning Beep
(With the advanced keyless
function)
If a key is left in the vehicle cabin and all
the doors and the boot are locked using
a separate key, a beep sound is heard for
about 10 seconds to remind the driver
that the key has been left in the vehicle
cabin. If this happens, open the door and
remove the key. A key removed from the
vehicle this way may not function because
its functions may have been temporarily
suspended. Perform the applicable
procedure to restore the functions of the
key (page 3-8 ).
i-stop Warning Beep
















 If the driver's door is opened while
engine idling is stopped, the warning
sound operates to notify the driver that
engine idling is stopped. It stops when
the driver's door is closed.
 


 The warning sound operates if the
following operations are performed
while the engine idling is stopped. In
such cases, the engine does not restart
automatically to ensure safety. Start the
engine using the normal method.
 

 
(European model)
 The driver's seat belt is unfastened and
the driver's door is opened.
 

 
(Except European model)



 
(Manual transaxle)
 With the shift lever in a position other
than neutral, the driver's seat belt is
unfastened and the driver's door is
opened.
 

 
(Automatic transaxle)
 With the selector lever in the D or
M (not in second gear fi xed mode)
position, the driver's seat belt is
unfastened and the driver's door is
opened.
i-ELOOP Warning Beep *
The beep will activate if you attempt to
drive the vehicle under the following
conditions.
 


 The i-ELOOP indicator light is fl ashing
green.
 


 “i-ELOOP Charging” is indicated in the
centre display (Type C/Type D audio).
The beep will stop when the vehicle is
stopped. Make sure the indicator light is
no longer illuminated and the message
is no longer displayed before driving the
vehicle.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–52
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Vehicle Speed Alarm *
The vehicle speed alarm function is
designed to alarm the driver via a single
beep sound and a warning indication in the
instrument cluster that the previously set
vehicle speed has been exceeded.
You can change the vehicle speed setting
at which the warning is triggered (page
4-30 ).
Tyre Infl ation Pressure Warning
Beep*
The warning beep sound will be heard
for about 3 seconds when there is any
abnormality in tyre infl ation pressures
(page 4-161 ).
Outside Temperature Warning
Beep
Warns the driver of the possibility of icy
roads when the outside temperature is low.
If the outside temperature is lower than
about 4 °C, a beep sound is heard once and
the outside temperature display fl ashes for
about ten seconds. (page 4-29 )
Rear Vehicle Monitoring (RVM)
System Warning Chime *
The warning chime activates at the same
time the RVM warning indicator light
begins fl ashing to alert the driver.
NOTE
A personalised function is available
to change the warning chime sound
volume.
Refer to Personalisation Features on
page 9-16 .
Lane Departure Warning System
(LDWS) Warning Sound *
While the system is operating, if the
system determines that the vehicle may
depart from the lane, it sounds a warning
sound.
NOTE
  The volume of the LDWS warning
sound can be changed.
 Refer to Personalisation Features on
page 9-16 .
  The type of the LDWS warning
sound can be changed.
 Refer to Personalisation Features on
page 9-16 .
Electronic Steering Lock Warning
Beep
The warning beep operates if the steering
wheel is not unlocked after the push button
start is pressed. (page 4-4 )
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–53
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Mazda Radar Cruise Control
(MRCC) System Warnings *
The Mazda Radar Cruise Control (MRCC)
system warnings notify the driver of
system malfunctions and cautions on use
when required.
Check based on the beep sound.
Cautions What to check
The beep sounds 1 time
while the Mazda Radar
Cruise Control (MRCC)
is operating The vehicle speed is
slower than 25 km/h (16
mph) and the Mazda
Radar Cruise Control
(MRCC) system has
been cancelled.
(European models)
The beep sounds 5 times
while driving
(Except European
models)
The beep continues to
sound while the vehicle
is being driven. The distance between
your vehicle and the
vehicle ahead is too
close. Verify the safety
of the surrounding area
and reduce vehicle
speed.
When the Mazda
Radar Cruise Control
(MRCC) is operating,
the beep sounds and the
Mazda Radar Cruise
Control (MRCC)
warning light (amber)
in the instrument cluster
fl ashes. A malfunction in the
system may be indicated.
Have your vehicle
inspected at an expert
repairer, we recommend
an Authorised Mazda
Repairer.
Speed Limiter Warning Beep *
If the vehicle speed exceeds the set speed
by about 3 km/h (2 mph) or more, a
warning beep operates continuously. The
warning beep operates until the vehicle
speed decreases to the set speed or less.
Collision Warning *
If there is the possibility of a collision
with a vehicle ahead, the beep sounds
continuously and a warning is indicated in
the display.
120 km/h Warning Beep *
If the vehicle speed exceeds 120 km/h, a
chime sounds for 5 seconds.
Power Steering Warning Buzzer
If the power steering system has
a malfunction, the power steering
malfunction light turns on or fl ashes and
the buzzer operates at the same time.
Refer to Warning/Indicator Lights on page
4-40 .
Over Rev. Buzzer *
The buzzer sounds to notify the driver if
the engine speed is about to exceed the
permissible engine speed.
CAUTION
Operate the accelerator and shift gears
according to the driving conditions so
that the buzzer does not sound. If the
engine speed exceeds the permissible
engine speed, the engine could be
damaged.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.9–12
Specifi cations
Specifi cations
Light Bulbs
Exterior light
Light bulb Category
Wattage UNECE *1
(SAE)
Headlights With xenon
fusion bulb
headlights High/Low beam 35 D4S (D4S)
With
halogen bulb
headlights High beam With running
lights 55 H15 (—)
Without
running lights 60 HB3 (9005)
Low beam 55 H11 (H11)
Running lights With xenon fusion bulb headlights LED
*2 — (—)
With halogen bulb headlights * 15 H15 (—)
Position lights With xenon fusion bulb headlights LED *2 — (—)
With halogen bulb headlights 5 W5W (—)
Front fog lights
* 55 H11 (H11)
Front direction indicator lights 21 WY21W
(7443NA)
Side direction indicator lights LED
*2 — (—)
High-mount brake light LED *2 — (—)
Rear direction indicator lights 21 WY21W
(7443NA)
Brake lights (With xenon fusion bulb headlights) LED
*2 — (—)
Tail lights (With xenon fusion bulb headlights) LED *2 — (—)
Brake lights/Tail lights (With halogen bulb headlights) 21/5 W21/5W (7443)
Reverse lights Saloon 16 W16W (921)
Hatchback 21 W21W (7440)
Rear fog light
* 21 W21W (7440)
Number plate lights 5 W5W (—)
*1 UNECE stands for United Nations Economic Commission for Europe.
*2 LED is the abbreviation for Light Emitting Diode.
.B[EB@&'&&"@&EJUJPOJOEC