weight MAZDA MODEL 3 HATCHBACK 2015 (in English) User Guide

Page 144 of 689

3–66
Before Driving
Towing
WARNING
Always keep tow loads within specifi ed limits as indicated in the Trailer Towing-Load
Table:
Attempting to tow loads greater than those specifi ed is dangerous as it may cause
serious handling and performance problems that could result in personal injury or
vehicle damage, or both.
Always keep the trailer nose weight within the specifi ed limits in the Trailer Towing-
Load Table:
Loading the trailer with more weight in the rear than in the front is dangerous. This
could cause loss of vehicle control and an accident.
NOTE
  The total trailer weight and nose weight can be determined by weighing the trailer on
platform scales at a highway weighing station or a trucking company.
  Appropriate total trailer weight and nose weight may prevent the danger of trailer sway
from crosswinds, rough roads, or other causes.
.B[EB@&'&&"@&EJUJPOJOEC

Page 147 of 689

3–69
Before Driving
Towing
Safety Chains
Safety chains must be used as a precautionary measure should the trailer become
unintentionally unhitched. They should cross under the trailer tongue and attach to the hitch.
Leave enough slack to allow full turns. Consult literature published by your trailer or hitch
manufacturer for more details.
WARNING
Make sure the safety chain is securely attached to both the trailer and the vehicle prior
to departure:
Towing a trailer without using a safety chain securely attached to both the trailer and
the vehicle is dangerous. If damage occurs to the coupling unit or hitch ball, the trailer
could wander into another lane and cause a collision.
Trailer Lights
CAUTION
Do not connect a trailer lighting system directly to the lighting system of your Mazda.
This may damage your vehicle's electrical system and lighting systems. To connect the
lighting system, consult an Authorised Mazda Dealer.
Trailer Brakes
Check the Maximum trailer towing-load table in Weight Limits (page 3-61 ), and if your
trailer weight exceeds the value in the TOTAL TRAILER WEIGHT (Trailer without brake),
trailer brakes are required.
If your trailer has brakes, make sure they meet regulations.
WARNING
Do not connect a hydraulic trailer-brake system to your vehicle's brake system:
Connecting a hydraulic trailer-brake system directly to the vehicle brake system is
dangerous and will result in inadequate braking and possible injury.
.B[EB@&'&&"@&EJUJPOJOEC

Page 148 of 689

3–70
Before Driving
Towing
Trailer Towing Tips
Before driving
 




 Verify that your Mazda maintains a near-normal attitude when a loaded or unloaded trailer
is connected. Do not drive if it has an abnormal front-up or front-down position. Inspect
for incorrect nose weight, worn suspension parts, and trailer overloading. Have the vehicle
inspected by an expert repairer, we recommend an Authorised Mazda Repairer.
 


 Make sure the trailer cargo is secure to prevent it from shifting.



 Make sure the mirrors meet all government regulations. Inspect them.



 Before starting out, inspect the operation of all vehicle and trailer lights and all vehicle-
to-trailer connections. Stop and re-inspect all lights and connections after driving a short
distance.
Driving
 




 Your Mazda will handle differently with a trailer in tow, so practice turning, backing, and
stopping in a traffi c-free area.




 Take time to get accustomed to the extra weight and length.



 Do not exceed 100 km/h (62 mph) with a trailer in tow. If the local legal maximum speed
with a trailer in tow is less than 100 km/h (62 mph), do not exceed the legal speed.
CAUTION
If the vehicle exceeds 100 km/h (62 mph) with a trailer in tow, the vehicle could be
damaged.
 


 When ascending a hill, shift into a lower gear to reduce the possibility of overloading or
overheating the engine, or both.
 


 When descending a hill, shift into a lower gear and use engine compression as a braking
effect. Pay constant attention to speed and use the brakes only as needed. Holding the
brake pedal down for a prolonged period may cause the brakes to overheat and lose
power.
.B[EB@&'&&"@&EJUJPOJOEC

Page 211 of 689

4–61
When Driving
Transaxle
Climbing steep grades from a stop
To climb a steep grade from a stopped
position:
1. Depress the brake pedal.
2. Shift to D or M1, depending on the
load weight and grade steepness.
3. Release the brake pedal while gradually
accelerating.
Descending steep grades
When descending a steep grade, shift to
lower gears, depending on load weight and
grade steepness. Descend slowly, using the
brakes only occasionally to prevent them
from overheating.
.B[EB@&'&&"@&EJUJPOJOEC

Page 219 of 689

*Some models.4–69
When Driving
Switches and Controls
Headlight Levelling *
The number of passengers and weight of
cargo in the luggage compartment change
the angle of the headlights.
Auto type
The angle of the headlights will be
automatically adjusted when turning on
the headlights.
The warning/indicator light turns on when
the system has a malfunction.
Refer to Warning/Indicator Lights on page
4-40 .
Manual type
The headlight levelling switch is used
to adjust the angle of the headlights
manually.
Select the proper headlight angle from the
following chart.
Front seat
Rear
seat Load Switch
Position
Driver Passenger
× — — — 0
× × — — 0
× × × — 2
× × × × 3
× — — × 4
× : Y e s
—: No
Running Lights *
Some countries require moving vehicles to
have their lights on (running lights) during
the daytime.
Running lights turn on automatically when
the ignition is switched ON. (Without
coming home light system)
The running lights turn on automatically
when the vehicle starts moving. (With
coming home light system)
They turn off when the parking brake is
operated or the shift lever is shifted to the
P position (automatic transaxle vehicle).
NOTE
(Except countries prohibited by law)
The running lights can be deactivated.
Refer to Personalisation Features on
page 9-16 .
.B[EB@&'&&"@&EJUJPOJOEC

Page 322 of 689

4–172
When Driving
Rear View Monitor
NOTE
Because there may be a difference between the displayed image, such as indicated below,
and the actual conditions when parking, always verify the safety at the rear of the vehicle
and the surrounding area directly with your eyes.
 
 In the image of the parking space (or garage) displayed below, even though the back
end and distance guide lines appear parallel in the monitor, they may not actually be
parallel on the ground.
  When parking in a space with a division line on only one side of the parking space, the
division line and the vehicle width guide line may appear parallel on the monitor, but
they may not actually be parallel on the ground.

Variance Between Actual Road Conditions and Displayed Image
Some variance occurs between the actual road and the displayed road. Such variance in
distance perspective could lead to an accident. Note the following conditions that may cause
a variance in distance perspective.
When the vehicle is tilted due to the weight of passengers and load
When the vehicle rear is lowered, the object displayed on the screen appears farther than the
actual distance.
VarianceObject
.B[EB@&'&&"@&EJUJPOJOEC

Page 516 of 689

6–20
Maintenance and Care
Owner Maintenance
Closing the Bonnet
1. Check under the bonnet area to make
certain all fi ller caps are in place and all
loose items (e.g. tools, oil containers,
etc.) have been removed.
2. Lift the bonnet, grasp the padded area
on the support rod, and secure the
support rod in the clip. Verify that the
support rod is secured in the clip before
closing the bonnet.
ClipClip
Clip
3. Lower the bonnet slowly to a height of
about 20 cm (7.9 in) above its closed
position and then let it drop.
CAUTION
When closing the bonnet, do not push
it excessively such as by applying your
weight. Otherwise, the bonnet could be
deformed.
.B[EB@&'&&"@&EJUJPOJOEC

Page 541 of 689

6–45
Maintenance and Care
Owner Maintenance
CAUTION
  Be careful not to allow the rubber
ring shown in the fi gure to be
scratched or damaged.
  If the rubber ring detaches, reattach it
before inserting a new battery.
Rubber ring
Ty r e s
For reasons of proper performance, safety,
and better fuel economy, always maintain
recommended tyre infl ation pressures and
stay within the recommended load limits
and weight distribution.
WARNING
Using Different Tyre Types:
Driving your vehicle with different
types of tyres is dangerous. It could
cause poor handling and poor braking;
leading to loss of control.
Except for the limited use of the
temporary spare tyre, use only the same
type tyres (radial, bias-belted, bias-type)
on all four wheels.
Using Wrong-Sized Tyres:
Using any other tyre size than what is
specifi ed for the vehicle (page 9-13 )
is dangerous. It could seriously affect
ride, handling, ground clearance,
tyre clearance, and speedometer
calibration. This could cause you to
have an accident. Use only tyres that
are the correct size specifi ed for the
vehicle.
.B[EB@&'&&"@&EJUJPOJOEC

Page 617 of 689

7–41
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning Action to be taken
Seat Belt Warning
Light
With warning light for front passenger's seat
The seat belt warning light illuminates if the driver or front passenger's seat is occupied and
the seat belt is not fastened with the ignition switched ON.
Without warning light for front passenger's seat
The seat belt warning light illuminates if the driver's seat is occupied and the seat belt is not
fastened with the ignition switched ON.
Seat belt reminder
Front seat
If the vehicle is driven with the driver or front passenger's seat belt unfastened, the seat belt
warning light illuminates and a warning beep sounds.
If the driver or front passenger's seat belt is unfastened (only when the front passenger seat
is occupied) and the vehicle is driven at a speed faster than about 20 km/h (12 mph), the
warning light will fl ash and a beep sound will be heard. After a short time, the warning
light stops fl ashing, but remains illuminated, and the beep sound stops. If a seat belt
remains unfastened, the warning light fl ashes and the beep sound activates again for a
given period of time.
Until a seat belt is fastened or a given period of time has elapsed, the beep sound will not
stop even if the vehicle speed falls below 20 km/h (12 mph).
NOTE
If a driver or front passenger's seat belt is unfastened after the beep sound turns off
(warning light remains illuminated), and the vehicle speed exceeds 20 km/h (12 mph),
the warning light fl ashes and beep sound activates again.
Placing heavy items on the front passenger seat may cause the front passenger seat
belt warning function to operate depending on the weight of the item.
To allow the front passenger seat weight sensor to function properly, do not place
and sit on an additional seat cushion on the front passenger seat. The sensor may not
function properly because the additional seat cushion could cause sensor interference.
When a small child sits on the front passenger seat, it is possible that the warning light
will not operate.
Rear seat
If the rear seat belts are not fastened while the ignition is switched ON, the driver and the
passenger will be informed by the warning lights.
The warning lights illuminate in two colours. When the seat belt is not fastened, the
warning light illumination is red. When the seat belt is fastened, the illumination is green.
The warning lights operate even when there is no passenger on the rear seat. The warning
beep only sounds if a seat belt is unfastened after being fastened.
NOTE
If the rear seat belts are not fastened in a specifi ed period of time after the engine has
been started, all the warning lights turn off.
.B[EB@&'&&"@&EJUJPOJOEC

Page 626 of 689

*Some models.7–50
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Seat Belt Warning Beep
Front seat
If the vehicle speed exceeds about 20
km/h (12 mph) with the driver or front
passenger's seat belt unfastened, a warning
beep sounds continuously. If the seat belt
remains unfastened, the beep sound stops
once and then continues for about 90
seconds. The beep stops after the driver or
front passenger's seat belt is fastened.
NOTE
  Some models do not have the seat
belt warning beep for the front
passenger's seat.
  Placing heavy items on the front
passenger seat may cause the front
passenger seat belt warning function
to operate depending on the weight
of the item.
  To allow the front passenger seat
weight sensor to function properly,
do not place and sit on an additional
seat cushion on the front passenger
seat. The sensor may not function
properly because the additional
seat cushion could cause sensor
interference.
  When a small child sits on the front
passenger seat, it is possible that the
warning beep will not operate.
Rear seat
The warning beep only sounds if a seat
belt is unfastened after being fastened.
Ignition Not Switched Off (STOP)
Warning Beep *
If the driver's door is opened while
the ignition is switched to ACC, a
continuous beep sound will be heard to
notify the driver that the ignition has not
been switched off (STOP). Left in this
condition, the keyless entry system will
not operate, the car cannot be locked, and
the battery power will be depleted.
Key Removed from Vehicle
Warning Beep
A beep sound will be heard 6 times and
the KEY warning light (red) will fl ash
continuously if the ignition has not been
switched off, all the doors are closed, and
the key is removed from the vehicle. This
is to notify the driver that the key has been
removed from the vehicle and the ignition
has not been switched off.
NOTE
Because the key utilizes low-intensity
radio waves, the Key Removed From
Vehicle Warning may activate if the key
is carried together with a metal object
or it is placed in a poor signal reception
area.
Request Switch Inoperable
Warning Beep (With the advanced
keyless function)
If the request switch is pressed with a door
open or ajar or the ignition has not been
switched off while the key is being carried,
a beep will be heard for about 2 seconds to
indicate that the doors and the liftgate/boot
lid cannot be locked.
.B[EB@&'&&"@&EJUJPOJOEC

Page:   < prev 1-10 11-20 21-30 next >