ignition MAZDA MODEL 3 HATCHBACK 2015 (in English) Owner's Guide

3–51
Before Driving
Security System
NOTE
  The theft deterrent system can also
be armed by activating the auto
relock function with all the doors,
the liftgate/boot lid and the bonnet
closed.
 Refer to Transmitter on page 3-4 .   The system will disarm if one of
the following operations takes place
within 20 seconds after pressing the
lock button:
 


 Unlocking any door.



 Opening any door or the liftgate/
boot lid.
 


 Opening the bonnet.



 Switching the ignition ON.



(With the advanced keyless
function)
  Pressing the electric liftgate/boot
lid opener while the key is being
carried.
  To rearm the system, do the arming
procedure again.
  When the doors are locked by
pressing the lock button on the
transmitter or using the auxiliary key
while the theft-deterrent system is
armed, the hazard warning lights will
fl ash once to indicate that the system
is armed.
To Turn Off an Armed System
An armed system can be turned off using
any one of the following methods:
 


 Pressing the unlock button on the
transmitter.
 


 Switching the ignition ON.



(With the advanced keyless function)
 Pressing a request switch on the doors.
The hazard warning lights will fl ash twice.
NOTE
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned off, the hazard warning
lights will fl ash twice to indicate that the
system is turned off.
To Stop an Alarm
A triggered alarm can be turned off using
any one of the following methods:
 


 Pressing the unlock button or the boot
button (saloon) on the transmitter.
 


 Starting the engine with the push button
start.
(With the advanced keyless function)
 


 Pressing a request switch on the doors.



 Pressing the electric liftgate/boot lid
opener while the key is being carried.
The hazard warning lights will fl ash twice.
.B[EB@&'&&"@&EJUJPOJOEC







3–56
Before Driving
Driving Tips
Rocking the Vehicle
WARNING
Do not spin the wheels at high speed,
and do not allow anyone to stand
behind a wheel when pushing the
vehicle:
When the vehicle is stuck, spinning
the wheels at high speed is dangerous.
The spinning tyre could overheat and
explode. This could cause serious
injuries.
CAUTION
Too much rocking may cause engine
overheating, transaxle failure, and tyre
damage.
If you must rock the vehicle to free it from
snow, sand or mud, depress the accelerator
slightly and slowly move the shift lever
from 1 (D) to R.
Winter Driving
Carry emergency gear, including tyre
chains, window scraper, fl ares, a small
shovel, jumper leads, and a small bag of
sand or salt.
Ask an expert repairer, we recommend an
Authorised Mazda Repairer to check the
following:
 


 Have the proper ratio of antifreeze in the
radiator.
  Refer to Engine Coolant on page 6-30 .



 Inspect the battery and its leads. Cold
reduces battery capacity.
 


 Use an engine oil appropriate for the
lowest ambient temperatures that the
vehicle will be driven in (page 6-23 ).
 


 Inspect the ignition system for damage
and loose connections.
 


 Use washer fl uid made with antifreeze—
but do not use engine coolant antifreeze
for washer fl uid (page 6-34 ).
NOTE

 Do not use the parking brake in
freezing weather as it may freeze.
Instead, shift to P with an automatic
transaxle and to 1 or R with a manual
transaxle. Block the rear wheels.
  Remove snow before driving. Snow
left on the windscreen is dangerous
as it could obstruct vision.
  Do not apply excessive force to a
window scraper when removing ice
or frozen snow on the mirror glass
and windscreen.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–1
4When Driving
Information concerning safe driving and stopping.



Start/Stop Engine ................................ 4-4
Ignition Switch ............................... 4-4
Starting the Engine ......................... 4-5
Turning the Engine Off ................ 4-12
i-stop
* ........................................... 4-13
Instrument Cluster and Display ...... 4-24
Meters and Gauges ....................... 4-24
Multi-information Display
* .......... 4-32
Active Driving Display* ............... 4-38
Warning/Indicator Lights ............. 4-40
Transaxle ............................................ 4-47
Manual Transaxle Operation ........ 4-47
Automatic Transaxle Controls ..... 4-50
Switches and Controls ...................... 4-62
Lighting Control ........................... 4-62
Front Fog Lights
* ......................... 4-70
Rear Fog Light* ............................ 4-71
Turn and Lane-Change Signals ...... 4-72
Windscreen Wipers and Washer ...... 4-73
Rear Window Wiper and
Washer
*......................................... 4-77
Headlight Washer* ........................ 4-78
Rear Window Defogger ............... 4-78
Horn ............................................. 4-80
Hazard Warning Flasher ............... 4-80
Brake .................................................. 4-82
Brake System ............................... 4-82
Emergency Stop Signal System ...... 4-85
Hill Launch Assist (HLA)* ........... 4-85 ABS/TCS/DSC ................................... 4-87
Antilock Brake System (ABS) ...... 4-87
Traction Control System (TCS)*...... 4-88
Dynamic Stability Control
(DSC)
* .......................................... 4-89
i-ELOOP ............................................ 4-91
i-ELOOP
* ..................................... 4-91
Fuel Economy Monitor ..................... 4-94
Fuel Economy Monitor
* ............... 4-94
Power Steering................................... 4-99
Power Steering ............................. 4-99
.B[EB@&'&&"@&EJUJPOJOEC







4–4
When Driving
Start/Stop Engine
Ignition Switch
Push Button Start Positions
The system operates only when the driver
is in the vehicle or within operational
range while the key is being carried.
Each time the push button start is pressed,
the ignition switches in the order of off,
ACC, and ON. Pressing the push button
start again from ON switches the ignition
off.
Indicator light
Push button start
NOTE
  The engine starts by pressing the
push button start while depressing
the clutch pedal (manual transaxle)
or the brake pedal (automatic
transaxle). To switch the ignition
position, press the push button start
without depressing the pedal.
  Do not leave the ignition switched
ON while the engine is not running.
Doing so could result in the battery
going dead. If the ignition is left in
ACC (For automatic transaxle, the
selector lever is in the P position, and
the ignition is in ACC), the ignition
switches off automatically after about
25 minutes. Off
The power supply to electrical devices
turns off and the push button start indicator
light (amber) also turns off.
In this position the steering wheel is
locked.
WARNING
Before leaving the driver's seat, always
switch the ignition off, set the parking
brake, and make sure the selector lever
is in P (automatic transaxle) or in 1st
gear or R (manual transaxle):
Leaving the driver's seat without
switching the ignition off, setting the
parking brake, and shifting the selector
lever to P (automatic transaxle) or
to 1st gear or R (manual transaxle)
is dangerous. Unexpected vehicle
movement could occur which could
result in an accident.
In addition, if your intention is to leave
the vehicle for even a short period, it
is important to switch the ignition off,
as leaving it in another position will
disable some of the vehicle's security
systems and run the battery down.
NOTE
(Locked steering wheel)
If the push button start indicator light
(green) is fl ashing and the beep sound
is heard, this indicates that the steering
wheel is not unlocked. To unlock the
steering wheel, press the push button
start while moving the steering wheel
left and right.
.B[EB@&'&&"@&EJUJPOJOEC







4–5
When Driving
Start/Stop Engine
ACC (Accessory)
Some electrical accessories will operate
and the indicator light (amber) illuminates.
In this position the steering wheel is
unlocked.
NOTE
The keyless entry system does not
function while the push button start has
been pressed to ACC, and the doors will
not lock/unlock even if they have been
locked manually.
O N
This is the normal running position after
the engine is started. The indicator light
(amber) turns off. (The indicator light
(amber) illuminates when the ignition
is switched ON and the engine is not
running.)
Some indicator lights/warning lights
should be inspected before the engine is
started (page 4-40 ).
NOTE
(SKYACTIV-G 1.5, MZR 1.6,
SKYACTIV-G 2.0)
When the push button start is pressed
to ON, the sound of the fuel pump
motor operating near the fuel tank can
be heard. This does not indicate an
abnormality.
Starting the Engine
WARNING
Radio waves from the key may affect
medical devices such as pacemakers:
Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will affect
the device.
NOTE
  The key must be carried because the
key carries an immobilizer chip that
must communicate with the engine
controls at short range.
  The engine can be started when the
push button start is pressed from off,
ACC, or ON.
  The push button start system
functions (function which can start
the engine by only carrying the
key) can be deactivated to prevent
any possible adverse effect on a
user wearing a pacemaker or other
medical device. If the system is
deactivated, you will be unable
to start the engine by carrying the
key. Consult an expert repairer, we
recommend an Authorised Mazda
Repairer for details. If the push
button start system functions have
been deactivated, you can start the
engine by following the procedure
indicated when the key battery goes
dead.
 Refer to Engine Start Function When
Key Battery is Dead on page 4-9 .
.B[EB@&'&&"@&EJUJPOJOEC







4–7
When Driving
Start/Stop Engine
CAUTION
If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) fl ashes, this
could indicate a problem with the engine
starting system and the inability to start
the engine or switch the ignition to ACC
or ON. Have your vehicle inspected at
an expert repairer, we recommend an
Authorised Mazda Repairer as soon as
possible.
NOTE
  Under the following conditions, the
KEY warning light (red) fl ashes after
the push button start is pressed to
inform the driver that the push button
start will not switch to ACC even if it
is pressed from off.
 


 The key battery is dead.



 The key is out of operational
range.
 


 The key is placed in areas where it
is diffi cult for the system to detect
the signal (page 3-7 ).
 


 A key from another manufacturer
similar to the key is in the
operational range.
NOTE
 (Forced engine starting method) If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) fl ashes, this
could indicate that the engine may
not start using the usual starting
method. Have your vehicle inspected
at an expert repairer, we recommend
an Authorised Mazda Repairer as
soon as possible. If this occurs, the
engine can be force-started. Press
and hold the push button start until
the engine starts. Other procedures
necessary for starting the engine
such as having the key in the cabin,
and depressing the clutch pedal
(manual transaxle) or the brake pedal
(automatic transaxle) are required.
  When the engine is force-started,
the KEY warning light (red) remains
illuminated and the push button
start indicator light (amber) remains
fl ashing.

(Automatic transaxle) When the selector lever is in the
neutral (N) position, the KEY
indicator light (green) and the push
button start indicator light (green) do
not illuminate.
7. Press the push button start after both
the KEY indicator light (green) in the
instrument cluster and the push button
start indicator light (green) illuminate.
.B[EB@&'&&"@&EJUJPOJOEC







4–8
When Driving
Start/Stop Engine
NOTE
  After starting the engine, the push
button start indicator light (amber)
turns off and the ignition switches to
the ON position.
 (SKYACTIV-G 1.5, MZR 1.6,
SKYACTIV-G 2.0)
 After pressing the push button start
and before the engine starts, the
operation sound of the fuel pump
motor from near the fuel tank can be
heard, however, this does not indicate
a malfunction.
NOTE
 (SKYACTIV-D 2.2)




 When starting the engine, do
not release the clutch pedal
(manual transaxle) or the brake
pedal (automatic transaxle) until
the glow indicator light in the
instrument cluster turns off and
the engine starts, after pressing the
push button start.
 


 If the clutch pedal (manual
transaxle) or the brake pedal
(automatic transaxle) is released
before the engine starts, depress
the clutch pedal (manual transaxle)
or the brake pedal (automatic
transaxle) again and press the push
button start to start the engine.
 


 If the ignition is left switched ON
for a long period of time without
the engine running after the glow
plugs are warmed up, the glow
plugs may warm up again which
will illuminate the glow indicator
light.
 


 The starter does not rotate until the
glow indicator light turns off.
8. After starting the engine, let it idle
for about ten seconds (Prohibited in
Germany).
.B[EB@&'&&"@&EJUJPOJOEC







4–11
When Driving
Start/Stop Engine
NOTE
  The engine cannot be started unless
the clutch pedal is fully depressed
(manual transaxle) or the brake
pedal is fully depressed (automatic
transaxle).
  If there is a malfunction with the
push button start function, the push
button start indicator light (amber)
fl ashes. In this case, the engine may
start, however, have the vehicle
checked at an expert repairer, we
recommend an Authorised Mazda
Repairer as soon as possible.
  If the push button start indicator light
(green) does not illuminate, perform
the operation from the beginning
again. If it does not illuminate,
have the vehicle checked at an
expert repairer, we recommend an
Authorised Mazda Repairer.
  To switch the ignition position
without starting the engine, perform
the following operations after the
push button start indicator light
(green) turns on.
1. Release the clutch pedal (manual
transaxle) or brake pedal
(automatic transaxle).
2. Press the push button start to
switch the ignition position. The
ignition switches in the order of
ACC, ON, and off each time the
push button start is pressed. To
switch the ignition position again,
perform the operation from the
beginning.
Emergency Operation for Starting
the Engine
If the KEY warning light (red) illuminates,
or the push button start indicator light
(amber) fl ashes, this could indicate that
the engine may not start using the usual
starting method. Have your vehicle
inspected at an expert repairer, we
recommend an Authorised Mazda Repairer
as soon as possible. If this occurs, the
engine can be force-started. Press and hold
the push button start until the engine starts.
Other procedures necessary for starting the
engine such as having the key in the cabin,
and depressing the clutch pedal (manual
transaxle) or the brake pedal (automatic
transaxle) are required.
.B[EB@&'&&"@&EJUJPOJOEC







4–12
When Driving
Start/Stop Engine
Turning the Engine Off
WARNING
Do not stop the engine while the
vehicle is moving:
Stopping the engine while the vehicle is
moving for any reason other than in an
emergency is dangerous. Stopping the
engine while the vehicle is moving will
result in reduced braking ability due to
the loss of power braking, which could
cause an accident and serious injury.
1. Stop the vehicle completely.
2. (Manual transaxle)
Shift into neutral and set the parking
brake.
(Automatic transaxle)
Shift the selector lever to the P position
and set the parking brake.
3. Press the push button start to turn off
the engine. The ignition position is off.
CAUTION
When leaving the vehicle, make sure the
push button start is off.
NOTE
 (SKYACTIV-G 1.5, SKYACTIV-G
2.0)
 The cooling fan in the engine
compartment could turn on for a few
minutes after the ignition is switched
from ON to OFF, whether or not the
A/C is on or off, to cool the engine
compartment quickly.
  When the push button start is pressed
from ON to ACC or OFF, the KEY
indicator light (green) may fl ash for
approximately 30 seconds indicating
that the remaining battery power of
the key is low.
 Replace with a new battery before
the key becomes unusable.
 Refer to Key Battery Replacement on
page 6-43 .
 (Automatic transaxle) If the engine is turned off while the
selector lever is in a position other
than P, the ignition switches to ACC.
Emergency Engine Stop
Continuously pressing the push button
start or quickly pressing it any number of
times while the engine is running or the
vehicle is being driven will turn the engine
off immediately. The ignition switches to
ACC.
.B[EB@&'&&"@&EJUJPOJOEC







4–22
When Driving
Start/Stop Engine
i-stop Warning Light (Amber)/i-stop Indicator Light (Green)
To ensure safe and comfortable use of the vehicle, the i-stop function constantly monitors
the driver's operations, the vehicle's interior and exterior environment, and the operational
status of the vehicle, and uses the i-stop warning light (amber) and i-stop indicator light
(green) to inform the driver of the operation status of the i-stop system or related warnings.
i-stop warning light (amber)
When illuminated
 




 This warning light stays on for a few seconds when the ignition is switched ON.



 The warning light illuminates when the i-stop OFF switch is pressed to turn the system
off.
 


 If any one of the following operations is performed after the engine has been
automatically stopped, the warning light illuminates. If this occurs, the engine does not
restart automatically for safety reasons, even if the clutch pedal is depressed (manual
transaxle) or the brake pedal is released (automatic transaxle). Use the standard engine
starting procedure to start the engine.
 

 
 The bonnet is opened.


 
(SKYACTIV-D 2.2)
 The driver intends to get out of the vehicle (driver's seat belt is unfastened and driver's
door is opened).
 


 If the i-stop warning light (amber) remains illuminated even after continuously pressing
the i-stop OFF switch under conditions other than when the bonnet is opened or the driver
has exited the vehicle (driver's seat belt is unfastened and driver's door is opened), consult
an expert repairer, we recommend an Authorised Mazda Repairer.
When fl ashing
The light fl ashes if there is any malfunction in the i-stop system. Consult an expert repairer,
we recommend an Authorised Mazda Repairer.
.B[EB@&'&&"@&EJUJPOJOEC