boot MAZDA MODEL 3 HATCHBACK 2015 (in English) Service Manual

6–9
Maintenance and Care
Scheduled Maintenance
Russia/Belarus/Azerbaijan/Kazakhstan
Maintenance Interval Number of months or kilometres, whichever comes fi rst.
Months 12 24 36 48 60 72 84 96 108 120 132 144
×1000 km 15 30 45 60 75 90 105 120 135 150 165 180
Engine valve clearance (Only MZR 1.6) Audibly inspect every 120,000 km, if noisy, adjust.
Drive belts *1 I I I I I I I I I I I I
Engine oil Russia/
Belarus/
Kazakhstan
*2 R R R R R R R R R R R R
Azerbaijan
*3 Replace every 5,000 km or 6 months.
Engine oil fi lter Russia/
Belarus/
Kazakhstan
*2 R R R R R R R R R R R R
Azerbaijan
*4 Replace every 10,000 km or 12 months.
Cooling system I I I I I I
Engine coolant
*5 Replace at fi rst 195,000 km or 10 years; after that, every
90,000 km or 5 years.
Air fi lter
*6
Russia/
Belarus/
Kazakhstan C C R C C R C C R C C R
Azerbaijan C R C R C R C R C R C R
Fuel fi lter Russia/
Belarus/
Kazakhstan Replace every 120,000 km.
Azerbaijan Replace every 60,000 km.
Fuel lines and hoses I I I I I I
Spark plugs
SKYACTIV-G
1.5 and
SKYACTIV-G
2.0
I I I I I I I R I I I I
MZR 1.6 I R I R I R I R I R I R
Evaporative system (if installed) I I I
Battery
*7 I I I I I I I I I I I I
Brake lines, hoses and connections I I I I I I I I I I I I
Brake fl uid
*8 R R R R R R
Parking brake I I I I I I I I I I I I
Disc brakes I I I I I I I I I I I I
Steering operation and linkages I I I I I I I I I I I I
Manual transaxle oil R R
Front and rear suspension, ball joints and wheel
bearing axial play I I I I I I I I I I I I
Driveshaft dust boots I I I I I I I I I I I I
Exhaust system and heat shields I I I I I I I I I I I I
.B[EB@&'&&"@&EJUJPOJOEC







6–13
Maintenance and Care
Scheduled Maintenance
Maintenance
Interval Number of months or kilometres (miles), whichever comes fi rst.
Months 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96
×1000 km 10 20 30 40 50 60 70 80 90
100 110 120 130 140 150 160
×1000 miles 6.25 12.5 18.75 25 31.25 37.5 43.75 50 56.25 62.5 68.75 75 81.25 87.5 93.75 100
Parking brake I I I I I I I I I I I I I I I I
Power brake unit (Brake booster)
and hoses I I I I I I I I
Disc brakes I I I I I I I I I I I I I I I I
Steering operation and linkages I I I I I I I I
Manual transaxle oil R
Front and rear suspension, ball
joints and wheel bearing axial play I I I I I I I I
Driveshaft dust boots I I I I
Exhaust system and heat shields Inspect every 80,000 km (50,000 miles).
Bolts and nuts on chassis and body T T T T T T T T
Body condition (for rust, corrosion
and perforation) Inspect annually.
Cabin air fi lter (if installed) R R R R R R R R
Tyres (including spare tyre) (with
infl ation pressure adjustment)
*10 I I I I I I I I I I I I I I I I
Tyre rotation
*10 Rotate every 10,000 km (6,250 miles).
Flat tyre repair kit (if installed) *11 Inspect annually.
Chart symbols:
I : Inspect: Inspect and clean, repair, adjust, fi ll up, or replace if necessary.
R : Replace
C : Clean
T : Tighten
Remarks:
*1 In the countries below, inspect the spark plugs at every 10,000 km (6,250 miles) or 12 months before replacing
them at the said interval.
Armenia, Angola, Georgia, Hong Kong, Jordan, Macau, Nigeria, Syria, El Salvador, Guatemala, Costa Rica,
Haiti, Bolivia, Honduras, Nicaragua, Peru, B.Virgin, Curacao, Vietnam, Myanmar, Cambodia
*2 Implement the fuel injection amount correction.
*3 Also inspect the air conditioner drive belts, if installed.
If the vehicle is operated primarily under any of the following conditions, inspect the drive belts more often than
the recommended intervals.
a) Driving in dusty conditions
b) Extended periods of idling or low speed operation
c) Driving for long period in cold temperatures or driving regularly at short distance only
d) Driving in extremely hot conditions
e) Driving in mountainous conditions continually
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–51
Maintenance and Care
Owner Maintenance
Headlights (Low/High beam)
Running lights
Headlights (Low beam)
Headlights (High beam)/Running lights *
Front fog lights *
Front direction indicator lights
Position lights
Side direction indicator lights
Brake lights (With xenon fusion headlights)
Tail lights (With xenon fusion headlights)
Brake lights/Tail lights (With halogen headlights)
Rear direction indicator lights
Tail lights (With xenon fusion headlights)
Reverse lights
Rear fog light *
Reverse light (Left-hand drive model)
Reverse light (Right-hand drive model)
Rear fog light *1 /Reverse light *2 (Left-hand drive model)
Rear fog light *1 /Reverse light *2 (Right-hand drive model)
High-mount brake light
Number plate lights
Overhead lights (Front)/Map lights
Vanity mirror lights *
Overhead lights (Rear) *
Boot light (Saloon)
Luggage compartment light (Hatchback)
*1 With rear fog light
*2 Without rear fog light
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–57
Maintenance and Care
Owner Maintenance
6. Turn the socket and bulb assembly
to remove it. Carefully remove the
bulb from its socket in the refl ector by
gently pulling it straight backward out
of the socket.
7. Install the new bulb in the reverse order
of the removal procedure.
Side direction indicator lights, Brake
lights (LED type), Tail lights (LED
type), Tail lights (Boot lid side/Liftgate
side)
* , High-mount brake light
Due to the complexity and diffi culty
of the procedure, the LED bulbs must
be replaced by an expert repairer, we
recommend an Authorised Mazda
Repairer.
NOTE
LED bulb replacement is not possible
because it is built into the unit. Replace
the unit.
Rear direction indicator lights, Brake
lights/Tail lights (Bulb type)
Saloon
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the centre of each plastic retainer
and remove the retainers.
3. Remove boot end trim.
InstallationRemoval
4. Pull the centre of each plastic retainer
and remove the retainers.
5. Peel back the boot side trim.
Removal
Installation
6. Turn the socket and bulb assembly
anticlockwise and remove it.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–61
Maintenance and Care
Owner Maintenance
NOTE
Verify that the cover is securely
installed.
Reverse lights(Saloon), Reverse lights/
Rear fog light (Hatchback)
*
Saloon
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the centre of each plastic retainer
and remove the retainers.
3. Peel back the boot lid trim.
Removal
Installation
4. Disconnect the electrical connector
from the bulb by pressing the tab on the
connector with your fi nger and pulling
the connector.
5. Turn the socket and bulb assembly
anticlockwise and remove it.
6. Disconnect the bulb from the socket.
7. Install the new bulb in the reverse order
of the removal procedure.
.B[EB@&'&&"@&EJUJPOJOEC







6–63
Maintenance and Care
Owner Maintenance
Number plate lights
Saloon
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the centre of each plastic retainer
and remove the retainers.
3. Peel back the boot lid trim.
Removal
Installation
4. Turn the socket and bulb assembly
anticlockwise and remove it.
5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse order
of the removal procedure. Hatchback
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Wrap a fl athead screwdriver with a soft
cloth to prevent damage to the lens,
and then remove the lens by carefully
prying on the edge of the lens with a
fl athead screwdriver.
3. Disconnect the bulb by pulling it out.
4. Install the new bulb in the reverse order
of the removal procedure.
.B[EB@&'&&"@&EJUJPOJOEC







6–65
Maintenance and Care
Owner Maintenance
Boot light (Saloon)
1. Press both sides of the lens cap to
remove it.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of the removal procedure.
Luggage compartment light
(Hatchback)
1. Wrap a small fl athead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
fl athead screwdriver.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse order
of the removal procedure.
Fuses
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls do
not work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an expert repairer,
we recommend an Authorised Mazda
Repairer as soon as possible.
Fuse Replacement
Replacing the fuses on the vehicle's left
side
If the electrical system does not work, fi rst
inspect the fuses on the vehicle's left side.
1. Make sure the ignition is switched off,
and other switches are off.
2. Open the fuse panel cover.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–1
7If Trouble Arises
Helpful information on what to do if a problem arises with the vehicle.



Parking in an Emergency ................... 7-2
Parking in an Emergency ............... 7-2
Roadside Emergency Triangle
Retaining Strap
* ............................. 7-2
Flat Tyre ............................................... 7-3
Spare Tyre and Tool Storage .......... 7-3
Emergency Flat Tyre Repair Kit* ........ 7-8
Changing a Flat Tyre (With spare
tyre) .............................................. 7-15
Battery Runs Out .............................. 7-21
Jump-Starting ............................... 7-21
Emergency Starting .......................... 7-24
Starting a Flooded Engine (MZR 1.6,
SKYACTIV-G 1.5 and SKYACTIV-G
2.0) ............................................... 7-24
Push-Starting ................................ 7-24
Running Out of Fuel (SKYACTIV-D
2.2) ............................................... 7-25
Overheating ....................................... 7-26
Overheating .................................. 7-26
Emergency Towing ............................ 7-28
Towing Description ...................... 7-28
Towing Hooks .............................. 7-29 Warning/Indicator Lights and Warning
Sounds ................................................ 7-32
If a Warning Light Turns On or
Flashes .......................................... 7-32
Message Indicated in Multi-
information Display ..................... 7-45
Message Indicated on Display* ...... 7-47
Warning Sound is Activated ......... 7-49
When Liftgate/Boot Lid Cannot be
Opened ............................................... 7-54
When Liftgate/Boot Lid Cannot be
Opened ......................................... 7-54
Active Driving Display Does Not
Operate ............................................... 7-56
If the Active Driving Display does not
operate .......................................... 7-56
.B[EB@&'&&"@&EJUJPOJOEC







7–7
If Trouble Arises
Flat Tyre
CAUTION
  When using the temporary spare
tyre, driving stability may decrease
compared to when using only the
conventional tyre. Drive carefully.
  To avoid damage to the temporary
spare tyre or to the vehicle, observe
the following precautions:
 


 Do not exceed 80 km/h (50 mph).



 Avoid driving over obstacles. Also,
do not drive through an automatic
car wash. This tyre's diameter is
smaller than a conventional tyre,
so the ground clearance is reduced
about 10 mm (0.4 in).
 


 Do not use a tyre chain on this tyre
because it will not fi t properly.




 Do not use your temporary spare
tyre on any other vehicle, it has
been designed only for your
Mazda.
 


 Use only one temporary spare tyre
on your vehicle at the same time.
To remove the spare tyre
1. Lift the boot/luggage compartment mat.
Boot/Luggage compartment mat
2. Turn the spare tyre hold-down bolt
anticlockwise.
Spare tyre hold-down bolt
To secure the spare tyre
Store the spare tyre in the reverse order
of removal. After storing, verify that the
spare tyre is stored securely.
.B[EB@&'&&"@&EJUJPOJOEC







7–13
If Trouble Arises
Flat Tyre
WARNING
Do not adhere the speed restriction
sticker to the padded area on the
steering wheel:
Adhering the speed restriction sticker
to the padded area on the steering
wheel is dangerous because the air
bag may not operate (deploy) normally
resulting in serious injury. In addition,
do not adhere the sticker to areas where
warning lights or the speedometer
cannot be viewed.
14. When the tyre infl ates to the specifi ed
tyre infl ation pressure, turn the air
compressor switch OFF, turn the sleeve
of the injection hose to the left, and pull
it out of the tyre valve. Turn the sleeve
of the injection hose to the left, and pull
it out of the tyre valve.
15. Remove the compressor hose from the
injection valve of the bottle. After that,
install the injection hose to the injection
valve of the bottle to prevent leakage of
any remaining sealant.
CAUTION
The remaining sealant in the hose may
spray out when the hose is removed.
Remove the hose carefully because you
may not be able to remove the sealant
contacting clothing or other objects.
16. Install the tyre valve cap.
17. Put the puncture tyre repair kit into the
boot/luggage compartment.
18. Start driving immediately to spread the
sealant in the tyre.
CAUTION
Carefully drive the vehicle at a speed of
80 km/h (50 mph) or less. If the vehicle
is driven at a speed of 80 km/h (50 mph)
or more, the vehicle may vibrate.
NOTE
(With Tyre Pressure Monitoring
System)
If the tyre is not properly infl ated, the
tyre pressure monitoring system warning
light will illuminate (page 4-40 ).
19. After driving the vehicle for about 10
minutes or 5 km (3 miles), connect
the air compressor to the tyre using
Step 9 of the procedure, and check the
tyre infl ation pressure using the tyre
pressure gauge on the air compressor. If
the tyre infl ation pressure is lower than
the specifi ed tyre infl ation pressure,
turn the air compressor ON and wait
until it reaches the specifi ed tyre
infl ation pressure.
.B[EB@&'&&"@&EJUJPOJOEC