charging MAZDA MODEL 3 HATCHBACK 2015 Owners Manual (in English)

*Some models.4–41
When Driving
Instrument Cluster and Display
Warning Lights
These lights turn on or fl ash to notify the user of the system operation status or a system
malfunction.
Signal Warning Lights Page
Master Warning Light *1 7-32
Brake System Warning Light *1*2 7-32
ABS Warning Light *1 7-32
Charging System Warning Light *1 7-32
Engine Oil Warning Light *1 7-32
Check Engine Light *1 7-32
(Red) High Engine Coolant Temperature Warning Light
*1 7-32
(Amber) * i-stop Warning Light *1 4-22
(Amber) RVM Warning Light *1 7-32
* Automatic Transaxle Warning Light *1 7-32
Power Steering Malfunction Indicator Light *1 7-32
Air Bag/Front Seat Belt Pretensioner System Warning Light *1 7-32
Low Fuel Warning Light 7-32
Seat Belt Warning Light 7-32
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–62
When Driving
Switches and Controls
Lighting Control
Headlights
Turn the headlight switch to turn the headlights, other exterior lights and instrument panel
illumination on or off.
When the lights are turned on, the lights-on indicator light in the instrument cluster turns on.
NOTE
To prevent discharging the battery, do not leave the lights on while the engine is off unless
safety requires them.
Without auto-light control
Without coming home light system
Switch Position
Ignition Position ON ACC or
OFF ON ACC or
OFF ON ACC or
OFF
Headlights — — — — × ×
Running lights
* × — — — — —
Tail lights
Position lights
Number plate lights
Instrument panel illumination — — × × × ×
×: On
—: Off
.B[EB@&'&&"@&EJUJPOJOEC







5–77
Interior Features
Audio System
CAUTION
  Always close the auxiliary jack/
USB port lid when it is not in use. If
foreign matter or liquid penetrates
the auxiliary jack/USB port, it may
cause a malfunction.
  Depending on the portable audio
device, noise may occur when the
device is connected to the vehicle
accessory socket. (If noise occurs, do
not use the accessory socket.)
NOTE
  This mode may not be usable
depending on the portable audio
device to be connected.
  Before using the auxiliary jack/USB
port, refer to the instruction manual
for the portable audio device.
  Use a commercially-available,
non-impedance (3.5
) stereo mini
plug for connecting the portable
audio unit to the auxiliary jack.
Before using the auxiliary jack, read
the manufacturer's instructions for
connecting a portable audio unit to
the auxiliary jack.
  To prevent discharging of the battery,
do not use the auxiliary input for
long periods with the engine off or
idling.
  When connecting a device to the
auxiliary jack or USB port, noise
may occur depending on the
connected device. If the device is
connected to the vehicle's accessory
socket, the noise can be reduced by
unplugging it from the accessory
socket.
How to connect USB port/
Auxiliary jack
Type A/Type B (Without CD player)
Auxiliary jack
USB port
Type A/Type B (With CD player)
USB port Auxiliary jack
.B[EB@&'&&"@&EJUJPOJOEC







5–156
Interior Features
Interior Equipment
CAUTION
  To prevent accessory socket damage
or electrical failure, pay attention to
the following:
 


 Do not use accessories that require
more than 120 W (DC 12 V, 10 A).
 


 Do not use accessories that are not
genuine Mazda accessories or the
equivalent.
 


 Close the cover when the
accessory socket is not in use to
prevent foreign objects and liquids
from getting into the accessory
socket.
 


 Correctly insert the plug into the
accessory socket.
 


 Do not insert the cigarette lighter
into the accessory socket.
 
 Noise may occur on the audio
playback depending on the device
connected to the accessory socket.
  Depending on the device connected
to the accessory socket, the vehicle's
electrical system may be affected,
which could cause the warning
light to illuminate. Disconnect the
connected device and make sure
that the problem is resolved. If the
problem is resolved, disconnect the
device from the socket and switch
the ignition off. If the problem is not
resolved, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
NOTE
To prevent discharging of the battery, do
not use the socket for long periods with
the engine off or idling.
Connecting the accessory socket
1. Open the lid.
2. Pass the connection plug cord through
the cutout of the console and insert the
plug into the accessory socket.
Plug
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–42
Maintenance and Care
Owner Maintenance
Battery Maintenance
To get the best service from a battery:




 Keep it securely mounted.



 Keep the top clean and dry.



 Keep terminals and connections clean,
tight, and coated with petroleum jelly or
terminal grease.
 


 Rinse off spilled electrolyte immediately
with a solution of water and baking
soda.
 


 If the vehicle will not be used for an
extended time, disconnect the battery
leads and charge the battery every six
weeks.
Inspecting Electrolyte Level *
A low level of electrolyte fl uid will cause
the battery to discharge quickly.
Upper level
Lower level
Inspect the electrolyte level at least once
a week. If it is low, remove the caps and
add enough distilled water to bring the
level between the upper and lower level
(illustration).
Do not overfi ll.
Examine the specifi c gravity of the
electrolyte with a hydrometer, especially
during cold weather. If it is low, recharge
the battery.
Battery Recharging
NOTE
  Before performing maintenance or
recharging the battery, turn off all
accessories and stop the engine.
  To disconnect the battery, remove the
negative lead fi rst. Install it last when
connecting the battery.
  Be sure to remove the caps before
recharging the battery.
 (With i-stop system) Do not quick-charge the battery.




 If the battery quickly discharges
because, for example, the lights were
left on too long with the engine off,
slow-charge it as required by battery
size and charger capacity.
 


 If the battery gradually discharges
because of high electric load while the
vehicle is being used, recharge it as
required by battery size and charger
capacity.
Battery Replacement
Contact an Authorised Mazda Dealer for a
battery replacement purchase.
.B[EB@&'&&"@&EJUJPOJOEC







7–23
If Trouble Arises
Battery Runs Out
1. Remove the battery cover.
2. Make sure the booster battery is 12
V and that its negative terminal is
grounded.
3. If the booster battery is in another
vehicle, do not allow both vehicles
to touch. Turn off the engine of the
vehicle with the booster battery and
all unnecessary electrical loads in both
vehicles.
4. Connect the jumper leads in the exact
sequence as in the illustration.
 

 
 Connect one end of a lead to the
positive terminal on the discharged
battery (1).
 

 
 Attach the other end to the positive
terminal on the booster battery (2).
 

 
 Connect one end of the other lead to
the negative terminal of the booster
battery (3).
 

 
 Connect the other end to the ground
point indicated in the illustration away
from the discharged battery (4).
5. Start the engine of the booster vehicle
and run it a few minutes. Then start the
engine of the other vehicle. 6. (With i-ELOOP system)
The i-ELOOP indicator light may fl ash
after the engine is started. The indicator
light turns off when the engine is
running and the charging is completed.
Make sure the i-ELOOP indicator light
is turns off before driving.
NOTE
  If the vehicle is driven with the
i-ELOOP indicator light fl ashing, a
beep sound is heard.
  If the steering wheel is operated with
the i-ELOOP indicator light fl ashing,
it may feel heavier than normal,
however, this does not indicate a
malfunction. The steering operation
will return to normal when the
i-ELOOP indicator light turns off.
  Do not remove the jumper leads
while the i-ELOOP indicator light is
fl ashing.
7. When fi nished, carefully disconnect the
leads in the reverse order described in
the illustration.
8. If the battery cover has been removed,
install it in the reverse order of
removal.
NOTE
Verify that the covers are securely
installed.
.B[EB@&'&&"@&EJUJPOJOEC







7–33
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
Electronic Brake Force
Distribution System
Warning If the electronic brake force distribution control unit determines that some components
are operating incorrectly, the control unit may illuminate the brake system warning
light and the ABS warning light simultaneously. The problem is likely to be the
electronic brake force distribution system.
WARNING
Do not drive with both the ABS warning light and brake warning light
illuminated. Have the vehicle towed to an expert repairer, we recommend an
Authorised Mazda Repairer to have the brakes inspected as soon as possible:
Driving when the brake system warning light and ABS warning light are
illuminated simultaneously is dangerous.
When both lights are illuminated, the rear wheels could lock more quickly in an
emergency stop than under normal circumstances.
Charging System
Warning Light If the warning light illuminates while driving, it indicates a malfunction of the
alternator or of the charging system.
Drive to the side of the road and park off the right-of-way. Consult an expert repairer,
we recommend an Authorised Mazda Repairer. CAUTION
Do not continue driving when the charging system warning light is illuminated
because the engine could stop unexpectedly.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–47
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Message Indicated on Display *
If a message is displayed in the centre display (Type C/Type D audio), take appropriate
action (in a calm manner) according to the displayed message.
(Display example)
Stop Vehicle in Safe Place Immediately
If the following messages are displayed in the centre display (Type C/Type D audio), a
vehicle system may be malfunctioning. Stop the vehicle in a safe place and contact an
Authorised Mazda Repairer.
Display Indicated Condition
Displays if the engine coolant temperature has
increased excessively.
Displays if the charging system has a malfunction.
.B[EB@&'&&"@&EJUJPOJOEC







7–48
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Make Sure the Message is No Longer Displayed
Displays in the following cases:
Display Indicated Condition/Action to be taken
Displays if i-ELOOP requires charging. Leave the
engine idling and wait until the message disappears.
NOTE
If the vehicle is driven while the message is
displayed, the buzzer will sound. If you turn the
steering wheel while the message is displayed, it
will feel heavier than normal, but this does not
indicate an abnormality. The steering operation will
return to normal after the message has disappeared.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–51
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Key Left-in-luggage Compartment
Warning Beep (With the advanced
keyless function)
If the key is left in the boot with all doors
locked and the boot lid closed, a beep
sound is heard for about 10 seconds to
remind the driver the key has been left in
the boot. If this happens, open the boot
lid by pressing the electric boot lid opener
and remove the key. A key removed from
the boot may not function because its
functions may have been temporarily
suspended. To restore the key function,
perform the applicable procedure (page
3-8 ).
Key Left-in-vehicle Warning Beep
(With the advanced keyless
function)
If a key is left in the vehicle cabin and all
the doors and the boot are locked using
a separate key, a beep sound is heard for
about 10 seconds to remind the driver
that the key has been left in the vehicle
cabin. If this happens, open the door and
remove the key. A key removed from the
vehicle this way may not function because
its functions may have been temporarily
suspended. Perform the applicable
procedure to restore the functions of the
key (page 3-8 ).
i-stop Warning Beep
















 If the driver's door is opened while
engine idling is stopped, the warning
sound operates to notify the driver that
engine idling is stopped. It stops when
the driver's door is closed.
 


 The warning sound operates if the
following operations are performed
while the engine idling is stopped. In
such cases, the engine does not restart
automatically to ensure safety. Start the
engine using the normal method.
 

 
(European model)
 The driver's seat belt is unfastened and
the driver's door is opened.
 

 
(Except European model)



 
(Manual transaxle)
 With the shift lever in a position other
than neutral, the driver's seat belt is
unfastened and the driver's door is
opened.
 

 
(Automatic transaxle)
 With the selector lever in the D or
M (not in second gear fi xed mode)
position, the driver's seat belt is
unfastened and the driver's door is
opened.
i-ELOOP Warning Beep *
The beep will activate if you attempt to
drive the vehicle under the following
conditions.
 


 The i-ELOOP indicator light is fl ashing
green.
 


 “i-ELOOP Charging” is indicated in the
centre display (Type C/Type D audio).
The beep will stop when the vehicle is
stopped. Make sure the indicator light is
no longer illuminated and the message
is no longer displayed before driving the
vehicle.
.B[EB@&'&&"@&EJUJPOJOEC