reverse lights MAZDA MODEL 3 HATCHBACK 2016 Owners Manual (in English)

4–30
When Driving
Transaxle
Shift Position Indication

The selector position is indicated when the
ignition is switched ON.
Gear position indication
In manual shift mode, the “M” of the shift
position indication illuminates and the
numeral for the selected gear is displayed.
Warning Light
The warning light turns on when the
system has a malfunction.
Refer to Warning Lights on page 4-21 .
Transaxle Ranges
 




y The shift position indicator light in the
instrument cluster illuminates. Refer to
Warning/Indicator Lights on page
4-20 .
 


y The selector lever must be in P or N to
operate the starter.

P (Park)
P locks the transaxle and prevents the front
wheels from rotating.
WARNING
Always set the selector lever to P and set
the parking brake:
Only setting the selector lever to the
P position without using the parking
brake to hold the vehicle is dangerous.
If P fails to hold, the vehicle could move
and cause an accident.

CAUTION
 


¾ Shifting into P, N or R while the vehicle is
moving can damage your transaxle.
 


¾ Shifting into a driving gear or reverse
when the engine is running faster than
idle can damage the transaxle.

R (Reverse)
In position R, the vehicle moves only
backward. You must be at a complete
stop before shifting to or from R, except
under rare circumstances as explained in
Rocking the Vehicle (page 3-46 ).
N (Neutral)
In N, the wheels and transaxle are not
locked. The vehicle will roll freely even
on the slightest incline unless the parking
brake or brakes are on.
WARNING
If the engine is running faster than idle,
do not shift from N or P into a driving
gear:
It's dangerous to shift from N or P
into a driving gear when the engine
is running faster than idle. If this is
done, the vehicle could move suddenly,
causing an accident or serious injury.

Do not shift into N when driving the
vehicle:
Shifting into N while driving is
dangerous. Engine braking cannot
be applied when decelerating which
could lead to an accident or serious
injury.

.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










4–87
When Driving
i-ACTIVSENSE
 


y The Blind Spot Monitoring (BSM) system will not operate under the following
circumstances.
 


y The vehicle speed falls below about 10 km/h (6.3 mph) even though the Blind Spot
Monitoring (BSM) OFF indicator light is turned off.
 


y The shift lever (manual transaxle)/selector lever (automatic transaxle) is shifted to
reverse (R) and the vehicle is reversing.
 


y In the following cases, the Blind Spot Monitoring (BSM) OFF indicator light À ashes and
operation of the system is stopped. If the Blind Spot Monitoring (BSM) OFF indicator
light remains À ashing, have the vehicle inspected at an Authorized Mazda Dealer as soon
as possible.
 


y Some problem with the system including the Blind Spot Monitoring (BSM) warning
lights is detected.
 


y A large deviation in the installation position of a radar sensor (rear) on the vehicle has
occurred.
 


y There is a large accumulation of snow or ice on the rear bumper near a radar sensor
(rear). Remove any snow, ice or mud on the rear bumper.
 


y Driving on snow-covered roads for long periods.



y The temperature near the radar sensors (rear) becomes extremely hot due to driving
for long periods on slopes during the summer.
 


y The battery voltage has decreased. 



y Under the following conditions, the radar sensors (rear) cannot detect target objects or it
may be dif¿ cult to detect them.




y A vehicle is in the detection area at the rear in an adjacent driving lane but it does not
approach. The Blind Spot Monitoring (BSM) system determines the condition based on
radar detection data.
 


y A vehicle is traveling alongside your vehicle at nearly the same speed for an extended
period of time.
 


y Vehicles approaching in the opposite direction.



y A vehicle in an adjacent driving lane is attempting to pass your vehicle.



y A vehicle is in an adjacent lane on a road with extremely wide driving lanes. The
detection area of the radar sensors (rear) is set at the road width of expressways.
 


y In the following cases, the activation of the Blind Spot Monitoring (BSM) warning lights
and the warning beep may not occur or they may be delayed.
 


y A vehicle makes a lane change from a driving lane two lanes over to an adjacent lane.



y Driving on steep slopes.



y Crossing the summit of a hill or mountain pass.



y The turning radius is small (making a sharp turn, turning at intersections).



y When there is a difference in the height between your driving lane and the adjacent
lane.
 


y Directly after pressing the Blind Spot Monitoring (BSM) switch and the system
becomes operable.

.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










4–88
When Driving
i-ACTIVSENSE
 


y If the road width is extremely narrow, vehicles two lanes over may be detected.
The detection area of the radar sensors (rear) is set according to the road width of
expressways.
 


y The Blind Spot Monitoring (BSM) warning lights may turn on in reaction to stationary
objects on the road or the roadside such as guardrails, tunnels, sidewalls, and parked
vehicles.

The walls at the entrance and exits of tunnels,
turnouts.


Objects such as guardrails and concrete walls
running alongside the vehicle.Places where the width between guardrails or
walls on each side of the vehicle narrows.
 

y A Blind Spot Monitoring (BSM) warning light may À ash or the warning beep may be
activated several times when making a turn at a city intersection.
 


y Turn off the Blind Spot Monitoring (BSM) system while pulling a trailer or while an
accessory such as a bicycle carrier is installed to the rear of the vehicle. Otherwise, the
radar’s radio waves will be blocked causing the system to not operate normally.
 


y In the following cases, it may be dif¿ cult to view the illumination/À ashing of the Blind
Spot Monitoring (BSM) warning lights equipped on the door mirrors.
 


y Snow or ice is adhering to the door mirrors.



y The front door glass is fogged or covered in snow, frost or dirt. 



y The system switches to the Rear Cross Traf¿ c Alert function when the shift lever (manual
transaxle) or the selector lever (automatic transaxle) is shifted to the reverse (R) position.
  Refer to Rear Cross Traf¿ c Alert (RCTA) on page 4-92 .
.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










4–89
When Driving
i-ACTIVSENSE
Blind Spot Monitoring (BSM) Warning Lights/Blind Spot Monitoring (BSM)
Warning Beep
The Blind Spot Monitoring (BSM) or Rear Cross Traf¿ c Alert (RCTA) system noti¿ es the
driver of the presence of vehicles in adjacent lanes to the rear of your vehicle using the
Blind Spot Monitoring (BSM) warning lights and the warning beep while the systems are
operational.
Blind Spot Monitoring (BSM) warning lights
The Blind Spot Monitoring (BSM) warning lights are equipped on the left and right door
mirrors. The warning lights turn on when a vehicle approaching from the rear in an adjacent
lane is detected.


When the ignition is switched ON, the malfunction warning light turns on momentarily and
then turns off after a few seconds.
Forward driving (Blind Spot Monitoring (BSM) system operation)
The Blind Spot Monitoring (BSM) system detects vehicles approaching from the rear and
turns on the Blind Spot Monitoring (BSM) warning lights equipped on the door mirrors
according to the conditions. Additionally, while a Blind Spot Monitoring (BSM) warning
light is illuminated, if the turn signal lever is operated to signal a turn in the direction
in which the Blind Spot Monitoring (BSM) warning light is illuminated, the Blind Spot
Monitoring (BSM) warning light À ashes.
Reverse driving (Rear Cross Traf¿ c Alert (RCTA) system operation)
The Rear Cross Traf¿ c Alert (RCTA) system detects vehicles approaching from the left and
right of your vehicle and À ashes the Blind Spot Monitoring (BSM) warning lights.
.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










4–92
When Driving
i-ACTIVSENSE
Rear Cross Traf¿ c Alert (RCTA)
T h e R e a r C r o s s T r a f¿ c Alert (RCTA) system is designed to assist the driver in checking the
area to the rear of the vehicle on both sides while the vehicle is reversing by alerting the
driver to the presence of vehicles approaching the rear of the vehicle.
The Rear Cross Traf¿ c Alert (RCTA) system detects vehicles approaching from the left and
right sides of the vehicle while the vehicle is being reversed out of a parking space, and
noti¿ es the driver of possible danger using the Blind Spot Monitoring (BSM) warning lights
and the warning buzzer.

Detection areas
Your vehicle

Rear Cross Traf¿ c Alert (RCTA) operation
1. The Rear Cross Traf¿ c Alert (RCTA) system operates when the shift lever (manual
transaxle) or the selector lever (automatic transaxle) is shifted to the reverse (R) position.
2. If there is the possibility of a collision with an approaching vehicle, the Blind
Spot Monitoring (BSM) warning light À ashes and the warning beep is activated
simultaneously.


.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










4–93
When Driving
i-ACTIVSENSE
WARNING
Always check the surrounding area visually before actually putting the vehicle in
reverse:
The system is only designed to assist you in checking for vehicles at the rear when putting
the vehicle in reverse. Due to certain limitations with the operation of this system, the
Blind Spot Monitoring (BSM) warning light may not fl ash or it might be delayed even
though a vehicle is behind your vehicle. Always make it your responsibility as a driver to
check the rear.

N O T E
 


y In the following cases, the BSM OFF Indicator Light turns on and operation of the
system is stopped. If the BSM OFF Indicator Light remains illuminated, have the vehicle
inspected at an Authorized Mazda Dealer as soon as possible.
 


y Some problem with the system including the Blind Spot Monitoring (BSM) warning
lights has occurred.
 


y A large deviation in the installation position of a radar sensor (rear) on the vehicle has
occurred.
 


y There is a large accumulation of snow or ice on the rear bumper near a radar sensor
(rear).
 


y Driving on snow-covered roads for long periods.



y The temperature near the radar sensors becomes extremely hot due to driving for long
periods on slopes during the summer.
 


y The battery voltage has decreased.
.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










4–94
When Driving
i-ACTIVSENSE
 


y Under the following conditions, the radar sensors (rear) cannot detect target objects or it
may be dif¿ cult to detect them.




y The vehicle speed when reversing is about 10 km/h (6 mph) or faster.



y The radar sensor (rear) detection area is obstructed by a nearby wall or parked
vehicle. (Reverse the vehicle to a position where the radar sensor detection area is no
longer obstructed.)

Your vehicle
 


y A vehicle is approaching directly from the rear of your vehicle.

Your vehicle
 


y The vehicle is parked on a slant.

Your vehicle
 


y Directly after pressing the BSM OFF switch and the system becomes operable. 



y In the following cases, it may be dif¿ cult to view the illumination/À ashing of the Blind
Spot Monitoring (BSM) warning lights equipped on the door mirrors.
 


y Snow or ice adheres to the door mirrors.



y The front door glass is fogged or covered in snow, frost or dirt. 



y Turn off the Rear Cross Traf¿ c Alert (RCTA) system while pulling a trailer or while an
accessory such as a bicycle carrier is installed to the rear of the vehicle. Otherwise,
the radio waves emitted by the radar will be blocked causing the system to not operate
normally.

.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










6–47
Maintenance and Care
Owner Maintenance
Light Bulbs

Overhead lights (Front)/
Map lights
Vanity mirror
lights
Headlights (Low/High beam)
Daytime running lights/
Parking lightsHeadlights (Low beam)
Headlights (High beam)/
Daytime running lights Fog lights
Fog lights Front side-marker lights
Front side-marker lights Side turn signal lights Side turn signal lightsOverhead lights (Front)/
Map lights
Vanity mirror
lights
Some models.
Front turn signal lights
Front turn signal lights
Brake lights (LED type)
Brake lights/Taillights/Rear
side-marker lights (Bulb type)
Taillights/Rear side-marker
lights (LED type)Taillights/Rear side-marker
lights (LED type)
Rear turn signal lights
Taillights (Trunk lid side)
Reverse lights
High-mount brake light
License plate lightsTrunk light
Overhead light (Rear)Overhead light (Rear)
Brake lights (LED type)Luggage
compartment light
Brake lights/Taillights/Rear
side-marker lights (Bulb type)
Rear turn signal lights
Taillights (Liftgate side)
Reverse lights
High-mount brake light
License plate lights
4-Door 5-DoorWith Xenon Fusion Headlights
With Halogen Headlights

.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










6–50
Maintenance and Care
Owner Maintenance
High-beam bulbs/Daytime running
lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Lift the hood.
3. Disconnect the connector from the unit
by pressing the tab on the connector
with your ¿ nger and pulling the
connector downward.



4. Turn the socket and bulb assembly
to remove it. Carefully remove the
bulb from its socket in the reÀ ector by
gently pulling it straight backward out
of the socket.



5. Install the new bulb in the reverse order
of the removal procedure.

Daytime running lights/Parking lights
(With xenon fusion headlights)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized Mazda
Dealer when the replacement is necessary.
Front turn signal lights, Parking lights/
Front side-marker lights (With halogen
headlights), Front side-marker lights
(With xenon fusion headlights)
1. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the left, and turn off engine.
If you are changing the left bulb, turn
the steering wheel to the right, and turn
off engine.
2. Make sure the headlight switch is off.
3. Pull the center of each plastic retainer
and remove the retainers.


Removal
Installation

.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC










6–51
Maintenance and Care
Owner Maintenance
4. Turn the screw counterclockwise and
remove it, and then partially peel back
the mudguard.



5. (Front turn signal lights)
Disconnect the connector from the unit
by pressing the tab on the connector
with your ¿ nger and pulling the
connector.



6. Turn the socket and bulb assembly
counterclockwise and remove it. 7. Disconnect the bulb from the socket.
Front turn signal lights



Parking lights/Front side-marker
lights (With halogen headlights),
Front side-marker lights (With
xenon fusion headlights)



8. Install the new bulb in the reverse order
of the removal procedure.

.B[EB@'"&"(@&EJUJPOJOEC


.B[EB@'"&"(@&EJUJPOJOEC