light MAZDA MODEL 6 2004 (in English) Service Manual

5-7
Driving Your Mazda
Starting and Driving
Form No. 8R29-EA-02I

Anti-Lock Brake System (ABS)
The ABS control unit continuously
monitors the speed of each wheel. If one
is about to lock up, the ABS responds by
automatically releasing and reapplying
that wheel’s brake.
The driver will feel a slight vibration in
the brake pedal and may hear a chattering
noise from the brake system. This is
normal when the ABS operates. Don’t
pump the brakes, continue to press down
on the brake pedal.
Brake Warning Light:Driving with the brake system
warning light on is dangerous. It
indicates that your brakes may not
work at all or that they could
completely fail at any time. If this
light remains on, after checking that
the parking brake is released, have
the brakes inspected immediately.
Don’t drive with this light on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
ABS Warning Light and Brake
Warning Light on at the Same Time:Driving when the brake system
warning light and ABS warning light
are on at the same time is dangerous.
When both lights are on, the rear
wheels could lock more quickly in an
emergency stop than under normal
circumstances.
Don’t drive with both lights on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
WARNING
ABS:The ABS cannot compensate for
unsafe and reckless driving, excessive
speed, tailgating (following another
vehicle too closely), and hydroplaning
(reduced tire friction and road
contact because of water on the road
surface). You can still have an
accident. So don’t rely on ABS as a
substitute for safe driving.
NOTE
Braking distances may be longer on
loose surfaces (snow or gravel, for
example) which usually have a hard
foundation. A vehicle with a normal
braking system may require less
distance to stop under these conditions
because the tires will build up a wedge
of surface layer when the wheels skid.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 7 Saturday, September 7, 2002 12:58 PM

5-8
Driving Your Mazda
Starting and Driving
Form No. 8R29-EA-02I

ABS Warning Light
The warning light stays on for a few
seconds when the ignition switch is turned
to the ON position.
If the ABS warning light stays on while
you’re driving, the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function
normally as if the vehicle had no ABS.
Should this happen, consult an Authorized
Mazda Dealer as soon as possible.
Brake Pad Wear Indicator
When the disc brake pads become worn,
the built-in wear indicators contact the
disc plates. This causes a screeching noise
to warn that the pads should be replaced.
When you hear this noise, consult an
Authorized Mazda Dealer as soon as
possible.
ABS Warning Light and Brake Warning Light on at the Same Time:Driving when the brake system
warning light and ABS warning light
are on at the same time is dangerous.
When both lights are on, the rear
wheels could lock more quickly in an
emergency stop than under normal
circumstances.
Don’t drive with both lights on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
WARNING
NOTE
When the engine is jump-started to
charge the battery, uneven rpm occurs
and the ABS warning light comes on.
This is due to a weak battery, not a
malfunction.
Recharge the battery.
Driving with Worn Disc Pads:Driving with worn disc pads is
dangerous. The brakes could fail and
cause a serious accident. As soon as
you hear a screeching noise consult
an Authorized Mazda Dealer.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 8 Saturday, September 7, 2002 12:58 PM

5-11
Driving Your Mazda
Starting and Driving
Form No. 8R29-EA-02I

Transaxle Ranges
The shift lever must be in P or N to
operate the starter.
P (Park)
P locks the transaxle and prevents the
front wheels from rotating.
R (Reverse)
In position R, the vehicle moves only
backward. You must be at a complete stop
before shifting to or from R, except as
explained under Rocking the Vehicle
(page 4-7).
N (Neutral)
In N, the wheels and transaxle are not
locked. The vehicle will roll freely even
on the slightest incline unless the parking
brake or brakes are on.D (Drive)
D is the normal driving position. From a
stop, the transaxle will automatically shift
through a 4-gear/5-gear
* sequence.*3.0-liter engine model
M (Manual)
M is the manual shift mode position.
Gears can be shifted up or down by
tapping the shift lever back or forward
from this position.
Holding the Vehicle with P:Setting the shift lever to the P position
without using the parking brake to
hold the vehicle is dangerous. If P
fails to hold, the vehicle could move
and cause an accident. To hold the
vehicle, set the shift lever to P AND
set the parking brake.
•
Shifting into P, N or R while the
vehicle is moving can damage your
transaxle.
•
Shifting into a driving gear or
reverse when the engine is running
faster than idle can damage the
transaxle.
WARNING
CAUTION
Shifting from N or P:It’s dangerous to shift from N or P
into a driving gear when the engine is
running faster than idle. If this is
done, the vehicle could move
suddenly, causing an accident or
serious injury. If the engine is
running faster than idle, don’t shift
from N or P into a driving gear.
Shifting into N while Driving:
Shifting into N while driving is
dangerous. Engine braking cannot be
applied when decelerating which
could lead to an accident or serious
injury. Do not shift into N when
driving the vehicle.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 11 Saturday, September 7, 2002 12:58 PM

5-17
Driving Your Mazda
Starting and Driving
Form No. 8R29-EA-02I
With cruise control, you can set and
automatically maintain any speed of more
than about 40 km/h (25 mph).

Cruise Main Indicator Light
This light comes on when the ON/OFF
switch is pressed and the cruise control
system is activated.

Cruise Set Indicator Light
This light comes on when a cruising speed
is set.

Activation/Deactivation
To activate the system, press the ON/OFF
switch.
The cruise main indicator light
illuminates.
To deactivate the system, press the switch
again.
The cruise main indicator light turns off.Cruise Control
Cruise Control Use:Using cruise control in the following
conditions could cause you to lose
control of the vehicle:
•Heavy or unsteady traffic
•Slippery or winding roads
•Similar restrictions that require
inconsistent speed
Don’t use cruise control in these
situations.
WARNING
Cruise Main Switch:Leaving the ON/OFF switch on when
not using the cruise control is
dangerous as it may be switched on
accidentally. This could result in loss
of vehicle control. Keep the ON/OFF
switch off when cruise control is not
in use.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 17 Saturday, September 7, 2002 12:58 PM

5-20
Driving Your Mazda
Starting and Driving
Form No. 8R29-EA-02I

To C a n c e l
To turn off the system, use one
of these
methods:
•
Press the ON/OFF switch.
•
Slightly depress the brake pedal.
•
Press the CANCEL button.
•(Manual transaxle)

Depress the clutch pedal.
The system is off when the ignition is off.The Traction Control System (TCS)
enhances traction and safety by regulating
engine torque. When the TCS detects
driving wheel slippage, it lowers engine
torque to prevent loss of traction.
This means that on a slick surface, the
engine adjusts automatically to provide
optimum power to the drive wheels
without causing them to spin and lose
traction.
NOTE
Cruise control will cancel at about 15
km/h (9 mph) below the preset speed
or below 40 km/h (25 mph).
Traction Control System
(TCS)
TCS and Unsafe Driving:The traction control system (TCS)
cannot compensate for unsafe and
reckless driving, excessive speed,
tailgating (following another vehicle
too closely), and hydroplaning
(reduced tire friction and road
contact because of water on the road
surface). You can still have an
accident. So don’t rely on the traction
control system as a substitute for safe
driving.
TCS and Snow and Ice:
Driving without proper traction
devices on snow and ice-covered
roads is dangerous. The traction
control system (TCS) alone cannot
provide adequate traction and you
could still have an accident. Use snow
tires or tire chains and drive at
reduced speeds when roads are
covered with ice and snow.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 20 Saturday, September 7, 2002 12:58 PM

5-21
Driving Your Mazda
Starting and Driving
Form No. 8R29-EA-02I

TCS Indicator Light
This indicator light stays on for a few
seconds when the ignition switch is turned
to the ON position. If the TCS is
operating, the indicator light flashes.
If the light stays on, the TCS may have a
malfunction and it may not operate
correctly. Take your vehicle to an
Authorized Mazda Dealer.

TCS OFF Indicator Light
This indicator light stays on for a few
seconds when the ignition switch is turned
to the ON position.
It also comes on when the TCS OFF
switch is pressed and TCS is switched off.
If the light stays on when the TCS is not
switched off, take your vehicle to an
Authorized Mazda Dealer. The TCS may
have a malfunction.
NOTE
•
In addition to the indicator light
flashing, a slight lugging sound will
come from the engine. This
indicates that the TCS is operating
properly.
•
On slippery surfaces, such as fresh
snow, it will be impossible to
achieve high rpm when the TCS is
on.
NOTE
After starting the engine when the
coolant temperature is extremely low,
the TCS is automatically turned off. At
this time, the TCS OFF indicator light
will remain on, but this does not
indicate an abnormality. After the
engine has warmed, TCS will resume
normal operation and the indicator
light will go out.
shuseizumi_J56J_8R29_EA_02I.book Page 21 Saturday, September 7, 2002 12:58 PM

5-22
Driving Your Mazda
Starting and Driving
Form No. 8R29-EA-02I

TCS OFF Switch
Press the TCS OFF switch to turn off the
TCS. The TCS OFF indicator light will
illuminate.
Press the switch again to turn the TCS
back on. The TCS OFF indicator light
will go out.
NOTE
•
When TCS is on and you attempt to
free the vehicle when it is stuck, or
drive it out of freshly fallen snow,
the TCS will activate. Depressing
the accelerator will not increase
engine power and freeing the
vehicle may be difficult. When this
happens, turn off the TCS.
•
If the TCS is off when the engine is
turned off, it automatically activates
when the ignition switch is turned
on.
•
Leaving the TCS on will provide the
best traction.
shuseizumi_J56J_8R29_EA_02I.book Page 22 Saturday, September 7, 2002 12:58 PM

5-24
Driving Your Mazda
Instrument Cluster and Indicators
Form No. 8R29-EA-02I

Speedometer
The speedometer indicates the speed of
the vehicle.

Odometer and Trip Meter
The display mode can be changed
between trip meter A and trip meter B by
pressing the selector while they are
displayed. The selected mode will be
displayed.
Odometer
The odometer records the total distance
the vehicle has been driven.
Tr i p m e t e r
The trip meter can record the total
distance of two trips. One is recorded in
trip meter A, and the other is recorded in
trip meter B.
For instance, trip meter A can record the
distance from the point of origin, and trip
meter B can record the distance from
where the fuel tank is filled.
When trip meter A is selected, pressing
the selector again within one second will
change to trip meter B mode.
When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed.
Selector
Odometer
Trip meter
Odometer
Odometer Trip meter A
Press the selector
Press the selector Trip meter B
NOTE
(Standard meter)

The odometer and trip meter can be
displayed as follows even when the
ignition switch is in the ACC or LOCK
position.
The headlight switch must be in the
or position to see the display.
•
Displays for 10 minutes after the
ignition switch is turned to the ACC
or LOCK position from the ON
position.
•
Displays for 10 minutes after any
door is opened.
shuseizumi_J56J_8R29_EA_02I.book Page 24 Saturday, September 7, 2002 12:58 PM

5-26
Driving Your Mazda
Instrument Cluster and Indicators
Form No. 8R29-EA-02I

Fuel Gauge
The fuel gauge shows approximately how
much fuel is in the tank. We recommend
keeping the tank over 1/4 full. When the
low fuel warning light illuminates or
when the needle is near E, refuel as soon
as possible.

Dashboard Illumination
When the headlight switch is in the or
position, rotate the thumb-wheel to
adjust the brightness of the dashboard
lights.

Instrument Cluster Dimmer
Cancel Button (Black-out meter)
When the headlight switch is in the or
position, the instrument cluster
illumination dims.
When driving on snowy or foggy roads, or
in other situations when the instrument
cluster’s visibility is reduced due to glare
from surrounding brightness, the
instrument cluster dimmer cancel button
increases the illumination intensity.
Press the button to increase the intensity
of the instrument cluster illumination.
Press the button again to return to the
previous illumination.
Low fuel
warning light
Bright
Dim
Instrument cluster
dimmer cancel
button
shuseizumi_J56J_8R29_EA_02I.book Page 26 Saturday, September 7, 2002 12:58 PM

5-27
Driving Your Mazda
Form No. 8R29-EA-02I
Warning/Indicator Lights and Beeps
Warning/Indicator Lights
Signal Warning/Indicator Lights Page
Brake System Warning Light 5-29
Charging System Warning Light 5-30
Engine Oil Pressure Warning Light 5-30
Check Engine Light 5-31
ABS Warning Light 5-31
Air Bag/Front Seat Belt Pretensioner System Warning Light 5-32
Low Fuel Warning Light 5-32
Warning/Indicator lights will appear in any of the highlighted areas
shuseizumi_J56J_8R29_EA_02I.book Page 27 Saturday, September 7, 2002 12:58 PM