stop start MAZDA MODEL 6 2018 (in English) User Guide

Page 279 of 863

Always apply the parking brake when parking the vehicle:
Not applying the parking brake when parking the vehicle is dangerous as the vehicle may
move unexpectedly and result in an accident. When parking the vehicle, shift the selector
lever to the P position (automatic transaxle vehicle) and apply the parking brake.
&$87,21
If you stop operating the accelerator pedal before the vehicle starts moving, the force holding
the vehicle in the stopped position may weaken. Firmly depress the brake pedal or depress the
accelerator pedal to accelerate the vehicle.
NOTE
xUnder the following conditions, a problem with the AUTOHOLD is occurring. Have your
vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer as
soon as possible.
xThe brake pedal operation demand warning light (red) in the instrument cluster flashes
and the warning sound is activated for about 5 seconds while the AUTOHOLD is
operating or when you press the AUTOHOLD switch.
xA message is indicated on the multi-information display and a warning sound is
activated for about 5 seconds while the AUTOHOLD is operating or when your press
the AUTOHOLD switch.
xIf you switch the ignition OFF while the AUTOHOLD is operating, the parking brake is
applied automatically to assist you with parking the vehicle.
xThe AUTOHOLD is cancelled when the selector lever/shift lever is shifted to R position
while the vehicle is on level ground, or facing up a hill or grade (as shown below).
Level ground : Driving in reverse (selector lever/shift lever in R)
Vehicle tilts forward
Vehicle tilts rearward
AUTOHOLD :
OperatesAUTOHOLD :
Does not operate,
cancelled AUTOHOLD :
Does not operate,
cancelled
:KHQ'ULYLQJ
%UDNH


Page 283 of 863

+LOO/DXQFK$VVLVW +/$
+/$LVDIXQFWLRQZKLFKDVVLVWVWKHGULYHU
LQDFFHOHUDWLQJIURPDVWRSZKLOHRQD
VORSH:KHQWKHGULYHUUHOHDVHVWKHEUDNH
SHGDODQGGHSUHVVHVWKHDFFHOHUDWRUSHGDO
ZKLOHRQDVORSHWKHIXQFWLRQSUHYHQWVWKH
YHKLFOHIURPUROOLQJ7KHEUDNLQJIRUFHLV
PDLQWDLQHGDXWRPDWLFDOO\DIWHUWKHEUDNH
SHGDOLVUHOHDVHGRQDVWHHSJUDGH
)RUYHKLFOHVZLWKDPDQXDOWUDQVD[OH
+/$RSHUDWHVRQDGRZQZDUGVORSHZKHQ
WKHVKLIWOHYHULVLQWKHUHYHUVH 5
SRVLWLRQDQGRQDQXSZDUGVORSHZKHQWKH
VKLIWOHYHULVLQDSRVLWLRQRWKHUWKDQWKH
UHYHUVH 5 SRVLWLRQ
)RUYHKLFOHVZLWKDQDXWRPDWLFWUDQVD[OH
+/$RSHUDWHVRQDGRZQZDUGVORSHZKHQ
WKHVHOHFWRUOHYHULVLQWKHUHYHUVH 5
SRVLWLRQDQGRQDQXSZDUGVORSHZKHQWKH
VHOHFWRUOHYHULVLQDIRUZDUGJHDU
:$ 5 1 , 1 *
Do not rely completely on HLA:
HLA is an auxiliary device for accelerating
from a stop on a slope. The system only
operates for about 2 seconds and
therefore, relying only on the system, when
accelerating from a stop is dangerous
because the vehicle may move (roll)
unexpectedly and cause an accident.
The vehicle could roll depending on the
vehicle's load or if it is towing something. In
addition, for vehicles with a manual
transaxle, the vehicle could still roll
depending on how the clutch pedal or the
accelerator pedal is operated.
Always confirm the safety around the
vehicle before starting to drive the vehicle.
NOTE
xHLA does not operate on a gentle slope.
In addition, the gradient of the slope on
which the system will operate changes
depending on the vehicle's load.
xHLA does not operate if the parking
brake is applied, the vehicle has not
stopped completely, or the clutch pedal
is released.
xWhile HLA is operating, the brake pedal
may feel stiff and vibrate, however, this
does not indicate a malfunction.
xHLA does not operate while the
TCS/DSC indicator light is illuminated.
Refer to Contact Authorised Mazda
Repairer and Have Vehicle Inspected on
page 7-49.
xHLA does not turn off even if the DSC
OFF switch is pressed to turn off the
TCS/DSC.
x(Automatic Transaxle)
Although the HLA does not operate
during idling stop, the vehicle roll
prevention function operates to prevent
vehicle roll.
:KHQ'ULYLQJ
%UDNH


Page 284 of 863

$QWLORFN%UDNH6\VWHP
$%6
7KH$%6FRQWUROXQLWFRQWLQXRXVO\
PRQLWRUVWKHVSHHGRIHDFKZKHHO,IRQH
ZKHHOLVDERXWWRORFNXSWKH$%6
UHVSRQGVE\DXWRPDWLFDOO\UHOHDVLQJDQG
UHDSSO\LQJWKDWZKHHO
VEUDNH

7KHGULYHUZLOOIHHODVOLJKWYLEUDWLRQLQ
WKHEUDNHSHGDODQGPD\KHDUDFKDWWHULQJ
QRLVHIURPWKHEUDNHV\VWHP7KLVLV
QRUPDO$%6V\VWHPRSHUDWLRQ&RQWLQXH
WRGHSUHVVWKHEUDNHSHGDOZLWKRXW
SXPSLQJWKHEUDNHV

7KHZDUQLQJOLJKWWXUQVRQZKHQWKH
V\VWHPKDVDPDOIXQFWLRQ
5HIHUWR&RQWDFW$XWKRULVHG0D]GD
5HSDLUHUDQG+DYH9HKLFOH,QVSHFWHGRQ
SDJH
:$ 5 1 , 1 *
Do not rely on ABS as a substitute for safe
driving:
The ABS cannot compensate for unsafe
and reckless driving, excessive speed,
tailgating (following another vehicle too
closely), driving on ice and snow, and
hydroplaning (reduced tyre friction and
road contact because of water on the road
surface). You can still have an accident.
NOTE
xBraking distances may be longer on
loose surfaces (snow or gravel, for
example) which usually have a hard
foundation. A vehicle with a normal
braking system may require less
distance to stop under these conditions
because the tyres will build up a wedge
of surface layer when the wheels skid.
xThe sound of the ABS operating may be
heard when starting the engine or
immediately after starting the vehicle,
however, it does not indicate a
malfunction.
:KHQ'ULYLQJ
$%67&6'6&


Page 353 of 863

¾Roads where frequent and repetitive acceleration and deceleration occur (Driving under
these conditions using the MRCC with Stop & Go function system is not possible).
¾When entering and exiting interchanges, service areas, and parking areas of highways (If
you exit a highway while headway control is in use, the vehicle ahead will no longer be
tracked and your vehicle may accelerate to the set speed).
¾Slippery roads such as ice or snow-bound roads (Tyres could spin causing you to lose
vehicle control, or the stop hold control may not operate.)
¾Long, descending slopes (to maintain distance between vehicles, the system automatically
and continuously applies the brakes which could result in the loss of brake power.)
¾Slopes with a steep gradient (The vehicle ahead may not be detected correctly, your vehicle
may slide while stopped by the stop hold control, and it may accelerate suddenly after it
starts moving.)
For safety purposes, switch the MRCC with Stop & Go function system off when it is not being
used.
Do not get out of the vehicle while the stop hold control is operating:
Getting out of the vehicle while the stop hold control is operating is dangerous as the vehicle
may move unexpectedly and result in an accident. Before getting out of the vehicle, switch the
MRCC with Stop & Go function system off, shift the selector lever to the P position, and apply
the parking brake.
&$87,21
If your vehicle is towed or you are towing something, switch the MRCC with Stop & Go
function system off to prevent a mis-operation.
NOTE
xThe MRCC with Stop & Go function system does not detect the following as physical
objects.
xVehicles approaching in the opposite direction
xPedestrians
xStationary objects (stopped vehicles, obstructions)
xIf a vehicle ahead is travelling at an extremely low speed, the system may not detect it
correctly.
xDuring headway control travel, do not set the system for detection of two-wheeled
vehicles such as motorcycles and bicycles.
xDo not use the MRCC with Stop & Go function system under conditions in which close
proximity warnings are frequently activated.
:KHQ'ULYLQJ
L$&7,96(16(


Page 356 of 863

,QVWUXPHQWFOXVWHU 7\SH%
Multi-information Display
MRCC Distance
between vehicle
display
MRCC Set vehicle speed Vehicle ahead display
Vehicle ahead display
MRCC Distance
between vehicle
display
MRCC Set
vehicle speed
Active driving display
,IWKHUHLVDSUREOHPZLWKWKH05&&ZLWK6WRS *RIXQFWLRQV\VWHPDPHVVDJHLV
GLVSOD\HGRQWKHPXOWLLQIRUPDWLRQGLVSOD\&KHFNWKHFHQWUHGLVSOD\WRYHULI\WKHSUREOHP
DQGWKHQKDYH\RXUYHKLFOHLQVSHFWHGE\DQH[SHUWUHSDLUHUZHUHFRPPHQGDQ$XWKRULVHG
0D]GD5HSDLUHU
5HIHUWR0HVVDJH,QGLFDWHGRQ'LVSOD\RQSDJH
▼▼&ORVH3UR[LPLW\:DUQLQJ
,I\RXUYHKLFOHUDSLGO\FORVHVLQRQWKHYHKLFOHDKHDGEHFDXVHWKHYHKLFOHDKHDGDSSOLHVWKH
EUDNHVVXGGHQO\ZKLOH\RXDUHWUDYHOOLQJLQKHDGZD\FRQWUROWKHZDUQLQJVRXQGDFWLYDWHV
DQGWKHEUDNHZDUQLQJLVLQGLFDWHGLQWKHGLVSOD\$OZD\VYHULI\WKHVDIHW\RIWKH
VXUURXQGLQJDUHDDQGGHSUHVVWKHEUDNHSHGDOZKLOHNHHSLQJDVDIHUGLVWDQFHIURPWKH
YHKLFOHDKHDG$GGLWLRQDOO\NHHSDVDIHUGLVWDQFHIURPWKHYHKLFOHVEHKLQG\RX
NOTE
In the following cases, the warnings and brakes may not operate even if your vehicle starts
closing in on the vehicle ahead.
xYou are driving your vehicle at the same speed as the vehicle ahead.
xDirectly after the MRCC with Stop & Go function system has been set.
xDirectly after the accelerator pedal is released.
xAnother vehicle cuts into the driving lane.
:KHQ'ULYLQJ
L$&7,96(16(


Page 357 of 863

▼6HWWLQJWKH6\VWHP
7KH05&&ZLWK6WRS *RIXQFWLRQV\VWHPRSHUDWHVZKHQDOORIWKHIROORZLQJFRQGLWLRQV
DUHPHW
x7KHYHKLFOHVSHHGLVDVIROORZV
x (XURSHDQPRGHOV
$ERXWNPK PSK WRNPK PSK
x ([FHSW(XURSHDQPRGHOV
$ERXWNPK PSK WRNPK PSK
x7KH05&&ZLWK6WRS *RIXQFWLRQLVWXUQHGRQ
x7KHEUDNHSHGDOLVQRWGHSUHVVHG
x7KHSDUNLQJEUDNHLVUHOHDVHG (OHFWULF3DUNLQJ%UDNH (3% LQGLFDWRUOLJKWLVWXUQHGRII 
x7KHUHLVQRSUREOHPZLWKWKH'6&
x$OOWKHGRRUVDUHFORVHG
x7KHGULYHU
VVHDWEHOWLVIDVWHQHG
x7KHVHOHFWRUOHYHULVLQWKHGULYH ' SRVLWLRQRUPDQXDO 0 SRVLWLRQ PDQXDOPRGH 
NOTE
xIn the following cases, the MRCC with Stop & Go function system is cancelled when the
vehicle is travelling at 30 km/h (19 mph) or less and “Mazda Radar Cruise Control
disabled under 30 km/h” is displayed in the multi-information display.
xThe Forward Sensing Camera (FSC) cannot detect target objects (There is problem
with the Forward Sensing Camera (FSC) or windscreen is dirty).
xThere is a problem with the stop hold control function.
xThere is a problem with the Electric Parking Brake (EPB).
xIt may not be possible to set the MRCC with Stop & Go function system directly after
starting the engine, while the DSC operation is being checked.
x(With Selective Catalytic Reduction (SCR) system)
It is not possible to set the MRCC with Stop & Go function system while the vehicle speed
is limited by the Selective Catalytic Reduction (SCR) system.
:KHQ'ULYLQJ
L$&7,96(16(


Page 363 of 863

▼6WRS+ROG&RQWURO
:KLOHLQKHDGZD\FRQWUROXVLQJWKH05&&ZLWK6WRS *RIXQFWLRQV\VWHP\RXUYHKLFOH
ZLOOVWRSZKHQDYHKLFOHDKHDGVWRSV:KHQWKHYHKLFOHLVVWRSSHGDQGWKHVWRSKROGFRQWURO
RSHUDWHVWKH05&&ZLWK6WRS *RIXQFWLRQLQGLFDWRUOLJKWWXUQVRQ
NOTE
xIf the MRCC with Stop & Go function system is cancelled during stop hold control, the
vehicle is held in its stopped position. The stop hold control can be cancelled by
performing one the following actions.
xPress the accelerator pedal and resume driving the vehicle.
xWhile forcefully depressing the brake, switch the MRCC with Stop & Go function
system off.
xThe parking brake is automatically applied and the vehicle is held in its stopped position
when 10 minutes have elapsed since the stop hold control operated. At this time, the
MRCC with Stop & Go function system is cancelled.
xIf the i-stop operation conditions are met during stop hold control, the engine stops even
though the brake pedal is not depressed.
Refer to i-stop on page 4-12.
xThe brake lights turn on during stop hold control.
7RUHVXPHGULYLQJ
$IWHUWKHYHKLFOHDKHDGVWDUWVPRYLQJZKLOH\RXUYHKLFOHLVVWRSSHGXQGHUVWRSKROGFRQWURO
SUHVVWKH5(6VZLWFKRUGHSUHVVWKHDFFHOHUDWRUSHGDOWRFDQFHOWKHVWRSKROGFRQWURODQG
UHVXPHGULYLQJ
NOTE
xWhen you resume driving by pressing the RES switch, your vehicle does not start moving
until the distance between your vehicle and the vehicle ahead lengthens to the specified
distance or farther.
xThe engine restarts automatically when any of the actions to resume driving are
performed while i-stop is operating.
xIf the MRCC with Stop & Go function is temporarily cancelled during stop hold control,
you cannot resume driving by pressing the RES switch when there are no vehicles in front
of your vehicle. Depress the accelerator pedal and resume driving the vehicle.
:KHQ'ULYLQJ
L$&7,96(16(


Page 364 of 863

xIf the vehicle ahead starts moving within 3 seconds after your vehicle is stopped by the
stop hold control, headway control will resume even if you do not resume driving your
vehicle, such as by depressing the accelerator pedal.
5HVXPHGULYLQJLQIRUPDWLRQ
,I\RXGRQRWUHVXPHGULYLQJZLWKLQDIHZVHFRQGVDIWHUWKHYHKLFOHDKHDGVWDUWVPRYLQJWKH
PXOWLLQIRUPDWLRQGLVSOD\YHKLFOHDKHDGLQGLFDWLRQIODVKHVWRXUJHWKHGULYHUWRUHVXPH
GULYLQJ
▼&UXLVH&RQWURO)XQFWLRQ
:KLOHWKLVIXQFWLRQLVRSHUDWLQJWKH
KHDGZD\FRQWURORSHUDWLRQLVFDQFHOOHG
DQGRQO\WKHFUXLVHFRQWUROIXQFWLRQ
RSHUDWHV
7KHYHKLFOHVSHHGFDQEHVHWPRUHWKDQ
DERXWNPK PSK 
8VHWKHFUXLVHFRQWUROIXQFWLRQRQ
H[SUHVVZD\VDQGRWKHUKLJKZD\VZKLFKGR
QRWUHTXLUHDORWRIUHSHDWHGDFFHOHUDWLRQ
DQGGHFHOHUDWLRQ
:$ 5 1 , 1 *
Do not use the cruise control function in
the following locations:
Otherwise, it could lead to an accident.
¾Roads with sharp curves and where
vehicle
traffic is heavy and there is
insufficient space between vehicles.
(Driving under these conditions using the
cruise control function is not possible)
¾Steep down slopes (Set speed may be
exceeded because sufficient engine
braking cannot be applied)
¾Slippery roads such as ice or snow-bound
roads (Tyres could spin causing you to
lose vehicle control)
Always drive carefully:
The warnings and brake control will not
operate after the headway control function
is cancelled and the system is switched to
only the cruise control function. Depress
the brake pedal to decelerate according to
the surrounding conditions while keeping a
safer distance from the vehicle ahead and
always driving carefully.
6ZLWFKLQJWRFUXLVHFRQWUROIXQFWLRQ
:KHQWKH02'(VZLWFKLVSUHVVHGXQWLO
WKHV\VWHPVZLWFKHVWRWKHFUXLVHPDLQ
LQGLFDWLRQ ZKLWH ZKLOHWKH05&&ZLWK
6WRS *RIXQFWLRQV\VWHPLVWXUQHGRQ
WKHV\VWHPVZLWFKHVWRWKHFUXLVHFRQWURO
IXQFWLRQ
:KHQWKHV\VWHPVZLWFKHVWRWKHFUXLVH
FRQWUROIXQFWLRQWKHLQGLFDWRUDQG
PXOWLLQIRUPDWLRQGLVSOD\QRWLI\WKHGULYHU
DVIROORZV
x7KH05&&ZLWK6WRS *RIXQFWLRQVHW
LQGLFDWLRQ JUHHQ RUWKH05&&ZLWK
6WRS *RIXQFWLRQPDLQLQGLFDWLRQ
ZKLWH LVWXUQHGRIIDQGWKHFUXLVHPDLQ
LQGLFDWLRQ ZKLWH LVWXUQHGRQ
x$PHVVDJHLVGLVSOD\HGLQWKH
PXOWLLQIRUPDWLRQGLVSOD\
:KHQ'ULYLQJ
L$&7,96(16(


Page 409 of 863

¾The front doors or the liftgate/boot is not fully closed.
¾The vehicle is on a road incline.
¾The door mirrors are retracted.
¾Do not hit the front/rear camera, front bumper, and door mirrors forcefully. The camera
position or installation angle may shift.
¾The cameras are of a waterproof structure. Do not disassemble, modify, or remove a
camera.
¾The camera cover is made of hard plastic, therefore do not apply oil film remover, organic
solvents, wax, or coating agents. If any such agent gets on the camera cover, wipe it off
using a soft cloth immediately.
¾Do not rub the camera lens forcefully, or clean it with an abrasive or hard brush. Otherwise,
it could scratch the camera lens and negatively affect the images.
¾Consult an Authorised Mazda Repairer for repair, painting, or replacement of the front/rear
camera, front bumper and door mirrors.
¾Heed the following cautions to assure that the 360°View Monitor operates normally.
¾Do not modify the suspensions.
¾Always use wheels of the specified type and size for the front and rear wheels. Consult an
Authorised Mazda Repairer for tyre replacement.
¾When the display is cold, images may leave trails or the screen might be darker than usual,
making it difficult to check the vehicle surroundings. Always confirm the safety at the front
and around the vehicle visually when driving.
¾The method for parking/stopping the vehicle using the 360°View Monitor differs depending
on the road circumstances/conditions and the vehicle conditions. When and how much you
turn the steering wheel will differ depending on the situation, , therefore always check the
vehicle surroundings directly with your eyes while using the system.
Also, before using the system, always make sure that the vehicle can be parked/stopped in
the parking/stopping space.
NOTE
xIf there are water droplets, snow, or mud on the camera lens, wipe it off using a soft cloth.
If the camera lens is especially dirty, wash it off with mild detergent.
xIf the area where the camera is installed, such as the liftgate/boot or door mirrors, has
been damaged in a vehicle accident, the camera (position, installation angle) may have
shifted. Always consult an Authorised Mazda Repairer to have the vehicle inspected.
xIf the camera is subjected to excessive changes in temperature such as by pouring hot
water on the camera during cold weather, the 360°View Monitor may not operate
normally.
xIf the battery voltage is low or the engine is restarted by the i-stop function, the screen
might be temporarily difficult to view, however, this does not indicate a problem.
:KHQ'ULYLQJ
L$&7,96(16(


Page 453 of 863

As an added safety feature, your vehicle has been equipped with a tyre pressure monitoring
system (TPMS) that illuminates a low tyre pressure telltale when one or more of your tyres is
significantly under-inflated. Accordingly, when the low tyre pressure telltale illuminates,
you should stop and check your tyres as soon as possible, and inflate them to the proper
pressure. Driving on a significantly under-inflated tyre causes the tyre to overheat and can
lead to tyre failure. Under-inflation also reduces fuel efficiency and tyre tread life, and may
affect the vehicle's handling and stopping ability.
Please note that the TPMS is not a substitute for proper tyre maintenance, and it is the
driver's responsibility to maintain correct tyre pressure, even if under-inflation has not
reached the level to trigger illumination of the TPMS low tyre pressure telltale.
Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when
the system is not operating properly.
The TPMS malfunction indicator is combined with the low tyre pressure telltale. When the
system detects a malfunction, the telltale will flash for approximately one minute and then
remain continuously illuminated. This sequence will continue upon subsequent vehicle
start-ups as long as the malfunction exists. When the malfunction indicator is illuminated,
the system may not be able to detect or signal low tyre pressure as intended. TPMS
malfunctions may occur for a variety of reasons, including the installation of replacement
or alternate tyres or wheels on the vehicle that prevent the TPMS from functioning properly.
Always check the TPMS malfunction telltale after replacing one or more tyres or wheels on
your vehicle to ensure that the replacement or alternate tyres and wheels allow the TPMS to
continue to function properly.
¾To avoid false readings, the system samples for a little while before indicating a problem. As
a result it will not instantaneously register a rapid tyre deflation or blow out.
▼6\VWHP(UURU$FWLYDWLRQ
:KHQWKHZDUQLQJOLJKWIODVKHVWKHUHPD\
EHDV\VWHPPDOIXQFWLRQ&RQVXOWDQ
$XWKRULVHG0D]GD'HDOHU
$V\VWHPHUURUDFWLYDWLRQPD\RFFXULQWKH
IROORZLQJFDVHV
x:KHQWKHUHLVHTXLSPHQWRUDGHYLFH
QHDUWKHYHKLFOHXVLQJWKHVDPHUDGLR
IUHTXHQF\DVWKDWRIWKHW\UHSUHVVXUH
VHQVRUV
x:KHQDPHWDOOLFGHYLFHVXFKDVD
QRQJHQXLQHQDYLJDWLRQV\VWHPLV
HTXLSSHGQHDUWKHFHQWUHRIWKH
LQVWUXPHQWSDQHOZKLFKPD\EORFN
UDGLRVLJQDOVIURPWKHW\UHSUHVVXUH
VHQVRUWRWKHUHFHLYHUXQLW
x:KHQXVLQJWKHIROORZLQJGHYLFHVLQWKH
YHKLFOHWKDWPD\FDXVHUDGLR
LQWHUIHUHQFHZLWKWKHUHFHLYHUXQLW
x$GLJLWDOGHYLFHVXFKDVDSHUVRQDO
FRPSXWHU
x$FXUUHQWFRQYHUWHUGHYLFHVXFKDVD
'&$&FRQYHUWHU
x:KHQH[FHVVVQRZRULFHDGKHUHVWRWKH
YHKLFOHHVSHFLDOO\DURXQGWKHZKHHOV
x:KHQWKHW\UHSUHVVXUHVHQVRUEDWWHULHV
DUHH[KDXVWHG
x:KHQXVLQJDZKHHOZLWKQRW\UH
SUHVVXUHVHQVRULQVWDOOHG
x:KHQXVLQJW\UHVZLWKVWHHOZLUH
UHLQIRUFHPHQWLQWKHVLGHZDOOV
x:KHQXVLQJW\UHFKDLQV
:KHQ'ULYLQJ
7\UH3UHVVXUH0RQLWRULQJ6\VWHP


Page:   < prev 1-10 11-20 21-30 next >